COLD ROLLED LOW CARBON STEEL SHEET 1.00 MM THICK .AS PER SPECN.IS-513-1994 D OR DD ( DRAWING QUALITY) SIZE-4X8 FEETS. BEST SURFACE,PROPERLY GREASED & PACKED TO AVOID RUSTING DURING TRANSIT. (PACK.SHOULD BE UP TO 2 TONS ONLY)
Specification
COLD ROLLED LOW CARBON STEEL SHEET 1.00 MM THICK .AS PER SPECN.IS-513-1994 D OR DD ( DRAWING QUALITY) SIZE-4X8 FEETS. BEST SURFACE,PROPERLY GREASED & PACKED TO AVOID RUSTING DURING TRANSIT. (PACK.SHOULD BE UP TO 2 TONS ONLY)
STEEL RD 22MM DIA IN HOT ROLLED AND ANNEALED CONDITION TO SPECN.BS:970 PT.1:1983 GD.817M40 OR 826M40.TEST PIECE TO BE TESTED AS PER SPECN.MACROETCH & NMIR TEST AS PER STORE DRG. CLEANLINESS TEST A SEPERATE TP TO BE HEAT TREATED TO ACHIEVE HARDNESS 45-61 HRC.T0 BE ULTRASONICALLY TESTED.(REQD.PISTON)
STEEL RD 12MM DIA IN ANNEALED AND COLD DRAWN CONDITION TO SPECN.BS:970.PT-I:1983 GD.817M40 OR 826M40 TEST PIECE TO TESTED AS PER ANNEXURE-A NATURE-C. (REQD.FOR EXTRACTOR PLUNGER OF MAG 7.62MM)
DRG.NO.SKM-281*2 'NI' SPOT TEST WILL BE CARRIED OUT ON 100% FORGINGS. MACRO ETCH AS PER ASTME-381 WITH ACCEPTANCE STANDARD AS C2, R2,S2 & NMIR TEST AS PER IS-4163-82.
Specification
DRG.NO.SKM-281*2 'NI' SPOT TEST WILL BE CARRIED OUT ON 100% FORGINGS. MACRO ETCH AS PER ASTME-381 WITH ACCEPTANCE STANDARD AS C2, R2,S2 & NMIR TEST AS PER IS-4163-82.
STEEL FLAT 25X32MM(1"X1-1/4")TO SPECN.BS:970:PT-1:1983 GD.080M40 IN HOT ROLLED & NORMALISED CONDITION. MATL TO BE TESTED AS PER ANNEXURE-C (REQD.FOR BAND FRONT SIGHT OF MAG 7.62MM)
Specification
STEEL FLAT 25X32MM(1"X1-1/4")TO SPECN.BS:970:PT-1:1983 GD.080M40 IN HOT ROLLED & NORMALISED CONDITION. MATL TO BE TESTED AS PER ANNEXURE-C (REQD.FOR BAND FRONT SIGHT OF MAG 7.62MM)
MILD STEEL SHEET 1.6 MM THICK AS PER IS-513/1994 GRDE-DHALF HARD,BEST SURFACE FEET. THE SHEETS SHOULD BE RUST FREE, PROPRELY GREASED & PACKED TO AVOID RUST- ING DURING TRANSIT.COLD ROLLED AND ANNEALED.
Specification
MILD STEEL SHEET 1.6 MM THICK AS PER IS-513/1994 GRDE-DHALF HARD,BEST SURFACE FEET. THE SHEETS SHOULD BE RUST FREE, PROPRELY GREASED & PACKED TO AVOID RUST- ING DURING TRANSIT.COLD ROLLED AND ANNEALED.
STEEL FLAT 17X47MM IN HOT ROLLED AND ANNEALED AT 650'C TO SPECN.BS:970:PT-3:1991 GD.945M38 T.P.TESTED IN `T'CONDITION MACRO ETCH TEST & NMIR TEST AS PER ANNEXURE-A NATURE-C. (REQD.FOR-SHOULDER LOCKING LEFT & RIGHT DS CAT 1005-007907)
Specification
STEEL FLAT 17X47MM IN HOT ROLLED AND ANNEALED AT 650'C TO SPECN.BS:970:PT-3:1991 GD.945M38 T.P.TESTED IN `T'CONDITION MACRO ETCH TEST & NMIR TEST AS PER ANNEXURE-A NATURE-C. (REQD.FOR-SHOULDER LOCKING LEFT & RIGHT DS CAT 1005-007907)
ST.FLAT 70X34MM IN HOT ROLLED & ANNEALED CONDITION TO SPECN. BS:970:PT-3:1991.GD.410S21 OR 420S29.TEST PIECE TO BE TESTED AS PER RULINF SECTION. MATL.SHOULD SATISFY MACRO-ETCH TEST & MICROSCOPIC NON-METALIC INCLUSION RATING(II) AS PER NATURE-C A SEPARATE T.P.TO BE HARDNED TO ACHIEVE HARDNESS 265-300 BHN
Specification
ST.FLAT 70X34MM IN HOT ROLLED & ANNEALED CONDITION TO SPECN. BS:970:PT-3:1991.GD.410S21 OR 420S29.TEST PIECE TO BE TESTED AS PER RULINF SECTION. MATL.SHOULD SATISFY MACRO-ETCH TEST & MICROSCOPIC NON-METALIC INCLUSION RATING(II) AS PER NATURE-C A SEPARATE T.P.TO BE HARDNED TO ACHIEVE HARDNESS 265-300 BHN
ST. BLANK OF RECEIVER PLATE LEFT & RIGHT TO DRG. SKM-960* WITH FIRM'S MAT. THE PROFILE & REF HOLES (SHOULDER LOCKING HOLE DIA 13 .39 (+_0.02) & BUSH MOUNTING FRONT HOLE DIA 18.025 (+_0.02) TO BE DONE SIMULT IN BOTH PLATES KEPT TOGETHER ONE ABOVE AND THER & NO. TO MAKE SET DRG. SKM 884*2 & SKM-884/1*3 ENCL
SLEEVE BOLT COVER IN FINISHED CONDITION DS CAT NO.1005-006624 DC (I) NO.26159-SA,DT.09-02-06 (MATL.ST.ROD 1/2" DIA GD.605M36 FROM L.F NO.0283001013/02830 00012 WILL BE SUP.BY.SAF .ON B/G.
Specification
SLEEVE BOLT COVER IN FINISHED CONDITION DS CAT NO.1005-006624 DC (I) NO.26159-SA,DT.09-02-06 (MATL.ST.ROD 1/2" DIA GD.605M36 FROM L.F NO.0283001013/02830 00012 WILL BE SUP.BY.SAF .ON B/G.
DS CAT NO.5310-002662 DC(I) 25349-SA DT.30.4.02 (MATL.ST.RD.19.05 MM DIA GD.605M36 FROM L.F.NO.0283000019 WILL BE SUPPLIED BY S.A.F.ON B/G.)AS PER DRG
Specification
DS CAT NO.5310-002662 DC(I) 25349-SA DT.30.4.02 (MATL.ST.RD.19.05 MM DIA GD.605M36 FROM L.F.NO.0283000019 WILL BE SUPPLIED BY S.A.F.ON B/G.)AS PER DRGAS PER DRG
SECONDRY REFIND AOD/VOD QUALITY STEEL ROD 46 MM DIA CONFORMING G TO THE SPECIFICTION JSS 9510-06:2000 (REV NO.3)CODE REF "B" IN HOT ROLLED,ANNEALED AND PEELED CONDT. IN MULTIPLE OF 413MM LENGTH TEST PIECETO BE TESTED IN T-1 CONDTION.MACROET- CH TESTING TO CON IS 13015:1991 & NMIR TEST (ANNEXURE-A ENCL)
Specification
SECONDRY REFIND AOD/VOD QUALITY STEEL ROD 46MM DIA CONFORMING G TO THE SPECIFICTION JSS 9510-06:2000 (REV NO.3)CODE REF "B" IN HOT ROLLED,ANNEALED AND PEELED CONDT. IN MULTIPLE OF 413MM LENGTH TEST PIECETO BE TESTED IN T-1 CONDTION.MACROET- CH TESTING TO CON IS 13015:1991 & NMIR TEST (ANNEXURE-A ENCL)
SCREW MACHINE FOR PLUG OBTURATIVE HOLE FOR INFRARED RAY PROTECTOR SUPPORT SCREW FOR MAG DS CAT NO. 5305-011218 DC (I) NO.27020-SA DT. 28.01.17 IN FINISHED CONDITION.
Specification
SCREW MACHINE FOR PLUG OBTURATIVE HOLE FOR INFRARED RAY PROTECTOR SUPPORT SCREW FOR MAG DS CAT NO. 5305-011218 DC (I) NO.27020-SA DT. 28.01.17 IN FINISHED CONDITION.
DS CAT NO.3120-004657 IN FINISHED CONDITION DC NO. 25298-SA , DT.19-03-02 (MAT.ST.RD.10 MM DIA GD.535A99 WILL BE SUPPLIED BY SAF ON B/G FROM L.F.NO.0352001010
Specification
DS CAT NO.3120-004657 IN FINISHED CONDITION DC NO. 25298-SA , DT.19-03-02 (MAT.ST.RD.10 MM DIA GD.535A99 WILL BE SUPPLIED BY SAF ON B/G FROM L.F.NO.0352001010
DS CAT NO. 3120-004658,DC NO.27108-SA,DT.23-06-17 IN FINISHED CONDITION (MATL.ST ROD.10 MM DIA WILL BE SUPPLIED BY S.A.F.ON B/G FROM L.F.NO.0352001010AS PER DRG.
Specification
DS CAT NO. 3120-004658, DC NO.27108-SA,DT.23-06-17 IN FINISHED CONDITION (MATL.ST ROD.10 MM DIA WILL BE SUPPLIED BY S.A.F.ON B/G FROM L.F.NO.0352001010AS PER DRG.AS PER DRG.