No. PROV/S/2599/TC-11/2009/01, Except That Clause No. 6.1 & 6.2 Which shall be suitable yarn count may be used in warp & weft in 3/1 twill weave to meet the functional & other constructional parameter along with feel & Finish & Clause no.16.1 which shall be as per schedule No.CQA(T&C)/P&M/35(d), except that the fabric shall be supplied in roll form only.
Specification
No. PROV/S/2599/TC-11/2009/01, Except That Clause No. 6.1 & 6.2 Which shall be suitable yarn count may be used in warp & weft in 3/1 twill weave to meet the functional & other constructional parameter along with feel & Finish & Clause no.16.1 which shall be as per schedule No.CQA(T&C)/P&M/35(d), except that the fabric shall be supplied in roll form only.
Drawing no.
Manufacturing Technology
Testing / Inspection Facility
21
38106
Metre
16243
3183000870
Small Arms Factory
The General Manager,
Kanpur
Kanpur
Kanpur, Uttar Pradesh
208009
NON FERROUS MATERIAL - ALUMINIUM.-TITANIUM- BORON MASTER ALLOY ROD 9.5 MM DIA (COIL FORM).
ITEM CODE : 0620173002 (VIRGIN MATERIAL)
Specification
AL.-TI. BORON MASTER ALLOY ROD 9.5 MM DIA (COIL FORM) IN RUNNING LENGTH.CHEMICAL COMPOSITION AS PER DESIGNATED "AA" HARDENER H 2252 WITH TITANIUM 4.5% TO 5.5%,BORON 0.8% TO 1.2%,SI-0.20% MAX,FE-0.30% MAX,V-0.20% MAX OTHER TRACE ELEMENTS i.e. Zn, Mg SHOULD NOT BE EXCEED 0.10% IN TOTAL.TOTAL IMPURITIES NOT TO EXCEED 0.80% REMINDER ALUMINIUM. SIZE :- 9.5 +/- 0.5MM DIA ROD HAVING COIL INNER DIA 370 +/- 10 MM, COIL WIDTH 300 +/- 10 MM DIA.
Drawing no.
Manufacturing Technology
Testing / Inspection Facility
06
AS PER REQUIREMENT
Kilogram
16245
OPF/ADVANCE VR/EOI/JANUARY-19/TAPE-01
Ordnance Parachute Factory
The General Manager,
Kanpur
Kanpur
Kanpur, Uttar Pradesh
208004
AS PER PARTICULARS GIVEN IN SHEET NO.102 OF DRAWING NO. ADRDE/1164/A-7(a)
WIDTH - 25.4 MM,
THICKNESS - 2.35 MM (MAX)
MASS/METER - 36.5 GM (MAX.)
NO. OF ENDS - 316 +2 (GOLDEN THREAD AT CENTRE)
PICKS/CM - 10 INCLUDING BOTH LAYERS
B.S. - 1850 KG (MIN.)
WEAVE - TUBULAR PLAIN
Specification
AS PER PARTICULARS GIVEN IN SHEET NO.102 OF DRAWING NO. ADRDE/1164/A-7(a)
WIDTH - 25.4 MM,
THICKNESS - 2.35 MM (MAX)
MASS/METER - 36.5 GM (MAX.)
NO. OF ENDS - 316 +2 (GOLDEN THREAD AT CENTRE)
PICKS/CM - 10 INCLUDING BOTH LAYERS
B.S. - 1850 KG (MIN.)
WEAVE - TUBULAR PLAIN
Except that in apperance finish and all other respects not
defined in this specn., the material shall conform to the
sealed pattern held in the custody of controller CQAT&C
Kanpur.There shall be no presence of starch. Scouring loss
Mild method is to be followed in lieu of severe method and shall not exceed 2% picks/cm (-1) tolerance to be permittd. In addition the firm shall get their name or trade mark woven/stamped alongwith seldvedges at a interval of one meter on either side of the tape.(2)Sampling plan and criteria of conformtty:as per QAI NO.CQAT&C/TC-8/11(b).(3)Packing Marking:As per relevant clause of specn.
Specification
Except that in apperance finish and all other respects not
defined in this specn., the material shall conform to the
sealed pattern held in the custody of controller CQAT&C
Kanpur.There shall be no presence of starch. Scouring loss
Mild method is to be followed in lieu of severe method and shall not exceed 2% picks/cm (-1) tolerance to be permittd. In addition the firm shall get their name or trade mark woven/stamped alongwith seldvedges at a interval of one meter on either side of the tape.(2)Sampling plan and criteria of conformtty:as per QAI NO.CQAT&C/TC-8/11(b).(3)Packing Marking:As per relevant clause of specn.
1-LENGTH PER ROLL(MIN) --100M ---IS:1954
2-WIDTH IN MM 28 + - 0.5 ---IS:1954
3-THICKNESS IN MM AT 200GM/CM^2 PRESSURE(MAX)--1.0--IS:7702
4-MASS,gm,MAX --17gm ---IS:4727
5-BREAKING LOAD "N" MIN. --7500 ---IS:1969
6-TOTAL NO.OF ENDS(FULL WIDTH) --135 ----IS:1963
7-PICKS/CM --14 -----IS:1963
8-LINEAR DENSITY OF YARN,TEX WARP ---93.3
WEFT ---23.3 X 2
9-WEAVE PLAIN ----VISUAL (2 PICKS/SHED)
Specification
1-LENGTH PER ROLL(MIN) --100M ---IS:1954
2-WIDTH IN MM 28 + - 0.5 ---IS:1954
3-THICKNESS IN MM AT 200GM/CM^2 PRESSURE(MAX)--1.0--IS:7702
4-MASS,gm,MAX --17gm ---IS:4727
5-BREAKING LOAD "N" MIN. --7500 ---IS:1969
6-TOTAL NO.OF ENDS(FULL WIDTH) --135 ----IS:1963
7-PICKS/CM --14 -----IS:1963
8-LINEAR DENSITY OF YARN,TEX WARP ---93.3
WEFT ---23.3 X 2
9-WEAVE PLAIN ----VISUAL (2 PICKS/SHED)
SPECN NO. AS PER PARTICULARS. 1.WIDTH (MM) 26+-1
2.THICKNESS AT 200 gms/SQ.CM PRESSURE,MM MAX 3.25
3.MASS/METERS,(gm) MAX 47
4-ENDS IN FULL WIDTH SUGGESTED 130
5.PICKS/CM SUGGESTED 12(INCLUDING BOTH LAYERS)
6.DENIER OF WARP/WEFT NOMINAL 840X3 /210X5
7.BREAKING STRENGTH kgf,min.N) 2000
8.TPM IN WARP/WEFT 100-200/100-200
Specification
SPECN NO. AS PER PARTICULARS. 1.WIDTH (MM) 26+-1
2.THICKNESS AT 200 gms/SQ.CM PRESSURE,MM MAX 3.25
3.MASS/METERS,(gm) MAX 47
4-ENDS IN FULL WIDTH SUGGESTED 130
5.PICKS/CM SUGGESTED 12(INCLUDING BOTH LAYERS)
6.DENIER OF WARP/WEFT NOMINAL 840X3 /210X5
7.BREAKING STRENGTH kgf,min.N) 2000
8.TPM IN WARP/WEFT 100-200/100-200
SPECN-ADRDE/SPECN/2002/57 THE TAPE SHALL BE IN CONTINUOUS LENGTH OF 105 M (EXCLUTING SAMPLING ) WITHOUT ANY FLAG OTHERWISE THAT ROLL WILL BE TREATED AS SHORT LENGTH.
Specification
SPECN-ADRDE/SPECN/2002/57 THE TAPE SHALL BE IN CONTINUOUS LENGTH OF 105 M (EXCLUTING SAMPLING ) WITHOUT ANY FLAG OTHERWISE THAT ROLL WILL BE TREATED AS SHORT LENGTH.
SPECN. NO IS: 3255-1979 Reaffirmed 2003. Except that:- a) In appearance finish and in other respectes not defined in this Specn.the material shall conform to the sealed pattern held in the custody of The Controller CQAT&C, Kanpur b)There shall be no presence of starch. (c) Scouring Loss Mild Method is to be followed in lieu of severe method & shall not exceed 2%. (d) (i) Ends in full width to be raised by 2.(ii) Picks/cms(-1) Tolerance to be permitted. (e) In addition the firm shall get their name or trade mark woven/stamped alongwith selvedges at a interval of one meter on either side of the tape (d)sampling plan and criteria AsPer QAI NO.CQATIC/TC-8/11(b)
Specification
SPECN. NO IS: 3255-1979 Reaffirmed 2003. Except that:- a) In appearance finish and in other respectes not defined in this Specn.the material shall conform to the sealed pattern held in the custody of The Controller CQAT&C, Kanpur b)There shall be no presence of starch. (c) Scouring Loss Mild Method is to be followed in lieu of severe method & shall not exceed 2%. (d) (i) Ends in full width to be raised by 2.(ii) Picks/cms(-1) Tolerance to be permitted. (e) In addition the firm shall get their name or trade mark woven/stamped alongwith selvedges at a interval of one meter on either side of the tape (d)sampling plan and criteria AsPer QAI NO.CQATIC/TC-8/11(b)
SPECIFICATION NO.: IS: 3255-1979 Except that :- i) In appearance shade finish and in other respects not
defined in this Specn. the material shall conform to the
sealed pattern held in the custody of the Controller,
CQAT&C, KANPUR. (ii) There shall be no presence of starch (iii) Scouring loss mild method is to be followed in lieu of severe method & shall not exceed 2% (Two percent). (iv) Sampling plan as per annexure (B) attached.
Packing and marking as per schedule No.CIT&C/PMS/65.
Specification
SPECIFICATION NO.: IS: 3255-1979 Except that :- i) In appearance shade finish and in other respects not
defined in this Specn. the material shall conform to the
sealed pattern held in the custody of the Controller,
CQAT&C, KANPUR. (ii) There shall be no presence of starch (iii) Scouring loss mild method is to be followed in lieu of severe method & shall not exceed 2% (Two percent). (iv) Sampling plan as per annexure (B) attached.
Packing and marking as per schedule No.CIT&C/PMS/65
TAPE COTTON 19 MM OG SPECIAL IS : 3255-1979 Except that :-
(i) The specified Picks Density is minimum.
(ii) The Density of Weft Yarn may be halved and Picks density (minimum) double in case of Needle Loom manufacturing.
(iii) In appearance shade, finish & in all other respect not defined in this IS Specn. The material shall conform to the sealed pattern held in the custody of the Controller, CQAT&C, Kanpur.
(iv) There shall be no presence of starch.
(v) Scouring loss Mild method is to be followed in lieu of severs method and shall not exceed 2.0% (Two percent).
(vi) 100% Sampling Testing & Inspection will be resorted to. Sampling plan as per annexure (a) attached. Packing and marking as per schedule CIT&C/PMS/65.
SPECIFICATION NO. : ADRDE/SPECN/1993/44(a) ROLL LENGTH 100 MTR. EXCLUDING SAMPLING.
Except that : - Shade should be as per approved sample held with QCM/OPF.
SPECN.NO.: IS:3255-1979 except that :-
(i)In appearance shade finish and in other respects not defined in this Specn. the material shall conform to the
sealed pattern held of the custody of the controller,CQAT&C, Kanpur. (ii)There shall be no presence of strach. (iii)End in full width to be raised by 2. (iv)Pick/cm(-1) Tolerance to be premitted. (v)100% Sampling/testing/inspection shall be resorted to. (vi) Scouring loss-Mild method is to be followed in view of severe method & shall not except 2%(two percent).
(vii) Sampling plan as per annexure (A) attached.
Specification
SPECN.NO.: IS:3255-1979 except that :-
(i)In appearance shade finish and in other respects not defined in this Specn. the material shall conform to the
sealed pattern held of the custody of the controller,CQAT&C, Kanpur. (ii)There shall be no presence of strach. (iii)End in full width to be raised by 2. (iv)Pick/cm(-1) Tolerance to be premitted. (v)100% Sampling/testing/inspection shall be resorted to. (vi) Scouring loss-Mild method is to be followed in view of severe method & shall not except 2%(two percent).
(vii) Sampling plan as per annexure (A) attached.
