Firm should have suitable infrastructure, manufacturing, inspection and testing facility to manufacture this item. Manufacturing facilities includes machines, capacity, trained manpower etc for the manufacturing of the subjected item(s). The firm should have manufacturing facilities like, CNC turning, milling and heat treatment facilities to meet the manufacturing requirements as applicable. OFT may carry out capacity verification of Bidder(s), if felt necessary.
Testing and inspection facilities: The firm should have CMM/UMM, Height Gauge, Profile Projector to meet the dimensional inspection of components as applicable. Firm must submit documentary proof to substantiate the same.
Firm should have suitable infrastructure, manufacturing, inspection and testing facility to manufacture this item. Manufacturing facilities includes machines, capacity, trained manpower etc for the manufacturing of the subjected item(s). The firm should have manufacturing facilities like, CNC turning, milling and heat treatment facilities to meet the manufacturing requirements as applicable. OFT may carry out capacity verification of Bidder(s), if felt necessary.
Testing and inspection facilities: The firm should have CMM/UMM, Height Gauge, Profile Projector to meet the dimensional inspection of components as applicable. Firm must submit documentary proof to substantiate the same.
1) Chemical & Mechanical properties as per std. given Specification.
2) Dimensional inspection for all dimension given in the drawing & other parameter which are mentioned in relevant specification.
1-Chemical and mechanical properties as per std. given drawing.
2- Dimensional inspection, for all dimensions given in the drawing a other parameter which are mentioned in relevant drawing
1-Chemical and mechanical properties as per std. given drawing.
2- Dimensional inspection, for all dimensions given in the drawing a other parameter which are mentioned in relevant drawing
FABRIC NYLON 58 GM U/D 105 CM MIN. WIDTH EXCLUDING SELVEDGE
Specification
SPECN NO. AS PER TECH. PARTICULARS
(a) MASS/SQ MET : 58 GM (MAX)
(b) BREAKING STRENGTH, BOTH WAYS : 60 KGF (MIN)
(C) TEARING STRENGTH, BOTH WAYS : 1.7 KGF (MIN)
(d) AIR POROSITY : 7-10 CU.FT/SQ.FT/SEC.
(e) THICKNESS:0.11M, MAX AT A PRESSUE OF 200GM/SQCM.
(f) WIDTH : 105CM MIN. WIDTH EXCLUDING SELVEDGE
(g) YARN LENIER DENSITY, BOTHWAYS : 45 DENIER (Nominal)
(h) TWIST OF YARN : WARP:200 TPM, WEFT: 150TPM
(i) THREAD DENSITY, BOTHWAYS :48-50/CM.
(j) WEAVE:2/1 TWILL
NOTE -THERE SHOULD NOT BE ANY TYPE OF YARN DISTORTION/SLIPPAG
1-Chemical and mechanical properties as per std. given drawing.
2- Dimensional inspection, for all dimensions given in the drawing a other parameter which are mentioned in relevant drawing
ST.FLAT 70X34MM IN HOT ROLLED & ANNEALED CONDITION TO SPECN. BS:970:PT-3:1991.GD.410S21 OR 420S29.TEST PIECE TO BE TESTED AS PER RULINF SECTION. MATL.SHOULD SATISFY MACRO-ETCH TEST & MICROSCOPIC NON-METALIC INCLUSION RATING(II) AS PER NATURE-C A SEPARATE T.P.TO BE HARDNED TO ACHIEVE HARDNESS 265-300 BHN
Specification
ST.FLAT 70X34MM IN HOT ROLLED & ANNEALED CONDITION TO SPECN. BS:970:PT-3:1991.GD.410S21 OR 420S29.TEST PIECE TO BE TESTED AS PER RULINF SECTION. MATL.SHOULD SATISFY MACRO-ETCH TEST & MICROSCOPIC NON-METALIC INCLUSION RATING(II) AS PER NATURE-C A SEPARATE T.P.TO BE HARDNED TO ACHIEVE HARDNESS 265-300 BHN
STEEL FLAT 17X47MM IN HOT ROLLED AND ANNEALED AT 650'C TO SPECN.BS:970:PT-3:1991 GD.945M38 T.P.TESTED IN `T'CONDITION MACRO ETCH TEST & NMIR TEST AS PER ANNEXURE-A NATURE-C. (REQD.FOR-SHOULDER LOCKING LEFT & RIGHT DS CAT 1005-007907)
Specification
STEEL FLAT 17X47MM IN HOT ROLLED AND ANNEALED AT 650'C TO SPECN.BS:970:PT-3:1991 GD.945M38 T.P.TESTED IN `T'CONDITION MACRO ETCH TEST & NMIR TEST AS PER ANNEXURE-A NATURE-C. (REQD.FOR-SHOULDER LOCKING LEFT & RIGHT DS CAT 1005-007907)
1) Chemical & Mechanical properties as per std. given drawing /Specification.
2) Dimensional inspection for all dimension given in the drawing & other parameter which are mentioned in relevant drawing/specification.
