LEVER HOLDER FOR 12 BORE PUMP ACTION GUN, DRG. NO. PAG-0012

STEEL IS:1875-1978. 45 C8.

DRG. NO. PAG-0012

REAR SIGHT FOR 12 BORE PUMP ACTION GUN, DRG. NO. PAG-0063

EN-19 OR MSF CLIX/3

DRG. NO. PAG-0063

FORE SIGHT FOR 12 BORE PUMP ACTION GUN, DRG. NO. PAG-0062 B

STEEL BS 970 EN 9, HRD: 300-350 HB

DRG. NO. PAG-0062 B

SEAR FOR 30-06 SPORTING RIFLE DRG. NO. TSP-704

BS 970 EN 19 (T)

DRG. NO. TSP-704

ROCKER AEMS SIGHT FOR 30-06 SPORTING RIFLE DRG. NO. TSP-723

STEEL BS:970, 070 M55 (EN 9)

DRG. NO. TSP-723

TRIGGER FOR 30-06 SPORTING RIFLE DRG. NO. TSP-706

STEEL BS: 970, 070 M55 (EN 9)

DRG. NO. TSP-706

PLUNGER REAR SIGHT FOR 30-06 SPORTING RIFLE DRG. NO. TSP-315

BS: 970 PT.1 GR. 070 M55 OR EN 9

DRG. NO. TSP-315

BLADE FORE SIGHT FOR 30-06 SPORTING RIFLE DRG. NO. TSP-316

BS: 970 EN 9 OR (IS:5517-93.55 C 8)

DRG. NO. TSP-316

LEAF REAR SIGHT FOR 30-06 SPORTING RIFLE DRG. NO. TSP-310

BS: 970 PT.1 GR.070 M55 OR EN 9

DRG. NO. TSP-310

BAND FORE SIGHT FOR 30-06 SPORTING RIFLE DRG. NO. TSP-303

STEEL BS 970 EN 8

DRG. NO. TSP-303

BRACKET REAR SIGHT FOR 30-06 SPORTING RIFLE DRG.TSP-302

B.S. 970 PT.I GR, 070 M55

DRG.TSP-302

CATCH SAFETY FOR 0.315" SPORTING RIFLE DRG. NO. SP-46

STEEL B.S. 970 PT.1:1983 GR. 070 M-55

DRG. NO. SP-46

SEAR FOR 0.315" SPORTING RIFLE DRG. NO. SP-60

STEEL B.S.970 PT-I/1983 GR. 080-M40

DRG. NO. SP-60

SPRING BOLT LOCKING FOR 0.315" SPORTING RIFLE DRG. NO. SP-62

B.S.970 PT.5:1972 GR.250 A-58 HRD. & TEMP. (480-52 VPN REF.)

DRG. NO. SP-62

RETICLE BTS7210037

RETICLE BTS7210037 OF K-10T

BTS7210037

WOODEN PACKING BOX TO DRG NO. 998-PB-3396 REQUIRED FOR HATCH TRAV.MECH-62 AS PER SCOPE OF WORK

WOODEN PACKING BOX TO DRG NO. 998-PB-3396

DRG NO. 998-PB-3396

GUN POSITION SENDING UNIT TO DRAWING NO. BL5.132.045

GUN POSITION SENDING UNIT TO DRAWING NO. BL5.132.045

BL5.132.045

Sewing cotton 100 D Tex/6 Khaki in Tube of 1000 mtrs. Specification : IS:1720-1978 (VR. NO. 31) Second Revision (Reaffirmed 2012)

Sewing cotton 100 D Tex/6 Khaki in Tube of 1000 mtrs. Specification : IS:1720-1978 (VR. NO. 31) Second Revision (Reaffirmed 2012)

• as per attached list (Manufacturing Technology Files )

• as per attached list (Testing / Inspection Facility Files )

HDPE Dot coated Printed Fusible Interlining Fabric 150 cm

1) Raw Material : 100% Cotton 2) Count (Warp & Weft) : 30s 3) Ends per Inch : 76+/- 5 4) Picks per Inch : 76 +/- 5 5) Width : 150 cm (Min) 6) Weave : Plain 7) Coating : HDPE 8) Colour : White 9) GSM : 148 +5/-2.5% 10) Shrinkage % : As per Appendix A of IND/TC/2089(a) 11) Bond Strength (Kgs) : > 2.0 As per IND/TC/2089(a) 12) Packing & Marking : As per CQA(T&C) Kanpur Schedule No. CQA(T&C)/PMS/35(d). Except that : a. Fabric in roll form shall not be less than 40 Mtrs in running length without stitching/ basting in between. b. Roll weight shall not exceed 50 kgs. c. Each roll of fabric shall be wrapped separately with polypropylene plain sheet. final packing of 2 rolls in one W.P Gunny/HDPE sheet. d. Dimension for paper tubes of fabric roll: Outer Diameter-3.5 cm, Inner Diameter-2.5 cm Thickness-0.5 cm. e. Fabric selvedges shall be wound evenly at one edge. 13) Sampling plan : As per annexure.

Sampling Plan attached as Drawing file

STEEL SHEET 1.00 MM THICK X (1000 X 2500 MM LONG) TO SPECN IS:5986-2002 GD Fe 410 HOT ROLLED & ANNEALED OR IS:2062-19999 GD Fe410WA OR IS 1079-1988 GD ST42

STEEL SHEET 1.00 MM THICK X (1000 X 2500 MM LONG) TO SPECN IS:5986-2002 GD Fe 410 HOT ROLLED & ANNEALED OR IS:2062-19999 GD Fe410WA OR IS 1079-1988 GD ST42

IND/TC/4552 (M) & Approved Sample

IND/TC/4552 (M) & Approved Sample

SPECN-ADRDE/SPCN.2000/54(b)

SPECN-ADRDE/SPCN.2000/54(b)

SPECN.NO:-ADRDE/QMS/TDTM/SPECN/84.

SPECN.NO:-ADRDE/QMS/TDTM/SPECN/84.

Packing of Shell 130MM HE

Packing of Shell 130MM HE as per Terms & Condition as Per Annexure 001/Store Dt. 26.10.2013 Enclosed

PIN CATCH MAGAZINE (THROUGH MIM ROUTE) FOR 9MM AUTO PISTOL. DRG. REF NO. 5315 - 009186 AND DRG NO. RFI. SK. 10120.

PIN CATCH MAGAZINE (THROUGH MIM ROUTE) FOR 9MM AUTO PISTOL. DRG. REF NO. 5315 - 009186 AND DRG NO. RFI. SK. 10120.

DRG. REF NO. 5315 - 009186 AND DRG NO. RFI. SK. 10120.

LEVER SLIDE LOCKING (THROUGH MIM ROUTE) DRG. REF. NO. 1005-003189 AND DRG. NO. RFI SK. 10128

LEVER SLIDE LOCKING (THROUGH MIM ROUTE) DRG. REF. NO. 1005-003189 AND DRG. NO. RFI SK. 10128

DRG. REF. NO. 1005-003189 AND DRG. NO. RFI SK. 10128

PIN ARM (THROUGH MIM ROUTE) DRG. REF. NO. 1005-003203 AND DRG. NO. RFI SK. 10124

PIN ARM (THROUGH MIM ROUTE) DRG. REF. NO. 1005-003203 AND DRG. NO. RFI SK. 10124

DRG. REF. NO. 1005-003203 AND DRG. NO. RFI SK. 10124

HAMMER MK-2 (THROUGH MIM ROUTE) DRG. REF. NO. 1005-003160 AND DRG. NO. RFI SK. 10119

HAMMER MK-2 (THROUGH MIM ROUTE) DRG. REF. NO. 1005-003160 AND DRG. NO. RFI SK. 10119

DRG. REF. NO. 1005-003160 AND DRG. NO. RFI SK. 10119

ADDE/BP/1(b) with 20-30 % elongation & proper heat setting

ADDE/BP/1(b) with 20-30 % elongation & proper heat setting

EQUILIBRATOR ASSY TO DRG. NO. 1015-000413

EQUILIBRATOR ASSY TO DRG. NO. 1015-000413

DRG. NO. 1015-000413

AS PER PARTICULARS: WIDTH: 36/(+2/-0)MM THICKNESS: 4.0MM(MAX MASS/MTR.:78GM(MAX). BREAKING STRENGTH: 2900KG(MIN) CONSTRUCTION OF YARN: WARP- 96.3X3 ie.96.3/1X3 TEX X FOLD: WEFT - 15.7X9. ENDS IN FULL WIDTH: 219 PICKS/DM: 66( BOTHLAYERS). TPM(RANGE):EARP-188-196, WEFT - 168-196. ELONGATION : 18-25%. WEAVE : TUBULAR PLAIN (3 ENDS WORKING AS ONE). HEAT SETTING : TAPE TUBULAR SHOULD HAVE PROPER HEAT SETTING.

AS PER PARTICULARS: WIDTH: 36/(+2/-0)MM THICKNESS: 4.0MM(MAX MASS/MTR.:78GM(MAX). BREAKING STRENGTH: 2900KG(MIN) CONSTRUCTION OF YARN: WARP- 96.3X3 ie.96.3/1X3 TEX X FOLD: WEFT - 15.7X9. ENDS IN FULL WIDTH: 219 PICKS/DM: 66( BOTHLAYERS). TPM(RANGE):EARP-188-196, WEFT - 168-196. ELONGATION : 18-25%. WEAVE : TUBULAR PLAIN (3 ENDS WORKING AS ONE). HEAT SETTING : TAPE TUBULAR SHOULD HAVE PROPER HEAT SETTING.

1- Width(mm) --- 25 mm. Appendix B of IS:3846:1984 2- Mass(gm/mt.)---12(max). Appendix C of IS:3846:1984 3- Ends(in full/width)------ 85+4/-0. IS:1963 4- Picks/cm.--- 20+2/-0 (total picks based on two thread working as one) IS:1963 5- Breaking load(20 cm X full width)("KN.") Minimum--2.4 IS:1969 6- Nature of material--100% Polyster. IS:667 7- pH Value(Cold Method)--6 to 8.5. IS:1390 8- % Water soluble matter(max)-- 1%. IS:3456 9- Weave-- 2/2 Twill weave. Visual

1- Width(mm) --- 25 mm. Appendix B of IS:3846:1984 2- Mass(gm/mt.)---12(max). Appendix C of IS:3846:1984 3- Ends(in full/width)------ 85+4/-0. IS:1963 4- Picks/cm.--- 20+2/-0 (total picks based on two thread working as one) IS:1963 5- Breaking load(20 cm X full width)("KN.") Minimum--2.4 IS:1969 6- Nature of material--100% Polyster. IS:667 7- pH Value(Cold Method)--6 to 8.5. IS:1390 8- % Water soluble matter(max)-- 1%. IS:3456 9- Weave-- 2/2 Twill weave. Visual

B251-800 IPG INTERNAL PIEZO GUAGE

B251-800 IPG INTERNAL PIEZO GUAGE

SPECN.NO.AS PER PARTICULAR 1.WIDTH : 25.4MM 2.THICKNESS : 2.35MM 3.Wt/mtr IN gms : 36.5 gms ( MAX.) 4.NO. OF ENDS : 316 +_ 2 GOLDEN THREADS AT CENTER (INCLUDING BOTH LAYERS ) 5.PICKS/CM : 11/12 6.DENIER OF YARN : 840 7.BREAKING LOAD : 1850 KG 8.WEAVE TUBULAR PLAIN 9.ELONGATION : 25% TO 35%

SPECN.NO.AS PER PARTICULAR 1.WIDTH : 25.4MM 2.THICKNESS : 2.35MM 3.Wt/mtr IN gms : 36.5 gms ( MAX.) 4.NO. OF ENDS : 316 +_ 2 GOLDEN THREADS AT CENTER (INCLUDING BOTH LAYERS ) 5.PICKS/CM : 11/12 6.DENIER OF YARN : 840 7.BREAKING LOAD : 1850 KG 8.WEAVE TUBULAR PLAIN 9.ELONGATION : 25% TO 35%

TAPE TEXTILE NYLON 43 MM U/D (BS=9000 N)

SPECIFICATION NO. ADRDE/SPECN/1985/27(b) Except that : – Twist (TPM) yarn as per clause No. 4.1 only Roll length 55 mtr. Excluding sampling.

ADRDE/SPECN/1985/27(b)

• As per Specification/Drawing

• As per Specification/Drawing

SPECN. NO IS: 3255-1979 Reaffirmed 2003. Except that:- a) In appearance finish and in other respectes not defined in this Specn.the material shall conform to the sealed pattern held in the custody of The Controller CQAT&C, Kanpur b)There shall be no presence of starch. (c) Scouring Loss Mild Method is to be followed in lieu of severe method & shall not exceed 2%. (d) (i) Ends in full width to be raised by 2.(ii) Picks/cms(-1) Tolerance to be permitted. (e) In addition the firm shall get their name or trade mark woven/stamped alongwith selvedges at a interval of one meter on either side of the tape (d)sampling plan and criteria AsPer QAI NO.CQATIC/TC-8/11(b)

SPECN. NO IS: 3255-1979 Reaffirmed 2003. Except that:- a) In appearance finish and in other respectes not defined in this Specn.the material shall conform to the sealed pattern held in the custody of The Controller CQAT&C, Kanpur b)There shall be no presence of starch. (c) Scouring Loss Mild Method is to be followed in lieu of severe method & shall not exceed 2%. (d) (i) Ends in full width to be raised by 2.(ii) Picks/cms(-1) Tolerance to be permitted. (e) In addition the firm shall get their name or trade mark woven/stamped alongwith selvedges at a interval of one meter on either side of the tape (d)sampling plan and criteria AsPer QAI NO.CQATIC/TC-8/11(b)

SPECIFICATION NO. : ADDE/BP/1(b).ROLL LENGTH 100 MTR.INCLUDING SAMPLING

SPECIFICATION NO. : ADDE/BP/1(b).ROLL LENGTH 100 MTR.INCLUDING SAMPLING

SPECIFICATION NO. : ADRDE/SPECN/68. ROLL LENGTH 90 MTR.EXCLUDING SAMPLING.

SPECIFICATION NO. : ADRDE/SPECN/68. ROLL LENGTH 90 MTR.EXCLUDING SAMPLING.

SPECIFICATION NO. : ADDE/BP/1(b).ROLL LENGTH 55 MTR. INCLUDING SAMPLING

SPECIFICATION NO. : ADDE/BP/1(b).ROLL LENGTH 55 MTR. INCLUDING SAMPLING

SPECN-ADRDE/SPCN.2000/54(b)

SPECN-ADRDE/SPCN.2000/54(b)

TAPE NYLON 66, 26mm TUBULAR BS 1850 KG ADRDE/SPECN/2000/54(c)

ADRDE/SPECN/2000/54(c)

TAPE NYLON 66,43 MM.B.S. 9000 N U/D

ADRDE/SPECN/1985/27(b)

• As Per Specification/Drawing

• As Per Specification/Drawing

SPECN.NO:-ADRDE/SPECN/2000/54(b)

SPECN.NO:-ADRDE/SPECN/2000/54(b)

ADRDE/SPCN/2000/54(b)

ADRDE/SPCN/2000/54(b)

SPECIFICATION NO.: IS: 3255-1979 Except that :- i) In appearance shade finish and in other respects not defined in this Specn. the material shall conform to the sealed pattern held in the custody of the Controller, CQAT&C, KANPUR. (ii) There shall be no presence of starch (iii) Scouring loss mild method is to be followed in lieu of severe method & shall not exceed 2% (Two percent). (iv) Sampling plan as per annexure (B) attached. Packing and marking as per schedule No.CIT&C/PMS/65.

SPECIFICATION NO.: IS: 3255-1979 Except that :- i) In appearance shade finish and in other respects not defined in this Specn. the material shall conform to the sealed pattern held in the custody of the Controller, CQAT&C, KANPUR. (ii) There shall be no presence of starch (iii) Scouring loss mild method is to be followed in lieu of severe method & shall not exceed 2% (Two percent). (iv) Sampling plan as per annexure (B) attached. Packing and marking as per schedule No.CIT&C/PMS/65

SPECN.NO. IS:4228-1979

SPECN.NO. IS:4228-1979

SPECIFICATION NO. : IS:9686-1980 PACKING & MARKING: CIT&C/PMS/130 SUITABLY.

SPECIFICATION NO. : IS:9686-1980 PACKING & MARKING: CIT&C/PMS/130 SUITABLY.

TAPE COTTON 19 MM OG SPECIAL

IS : 3255-2024 Except that :- (i) In appearance shade, finish & in all other respect not defined in this IS Specn. The material shall conform to the sealed pattern held in the custody of the Controller, CQAT&C, Kanpur. (ii) There shall be no presence of starch. (iii) Scouring loss Mild method is to be followed in lieu of severs method and shall not exceed 2.0% (Two percent). (iv) 100% Sampling Testing & Inspection will be resorted to. Sampling plan as per annexure (a) att ached. Packing and marking as per schedule CIT&C/PMS/65.

• As per Specification/Drawing

• As per Specification/Drawing

AS PER ADRDE SPCN.NO.ADDE/BP/1(b).

AS PER ADRDE SPCN.NO.ADDE/BP/1(b).

SPECN.NO.JSS:8315-6.

SPECN.NO.JSS:8315-6.

SPECN. NO. Best Trade Quality

SPECN. NO. Best Trade Quality

TAPE NYLON 30 MM O.G. BS 580 KG

SPECIFICATION NO. : ADRDE/SPECN/1993/44(a) ROLL LENGTH 100 MTR. EXCLUDING SAMPLING. Except that : - Shade should be as per approved sample held with QCM/OPF.

• AS PER SPECIFICATION/DRAWING

• AS PER SPECIFICATION/DRAWING

SPCN.: IS:3687-1987

SPCN.: IS:3687-1987

PCB CONTROL MODULE AS PER DRG. NO. 7084.32.03.100

PCB CONTROL MODULE AS PER DRG. NO. 7084.32.03.100

7084.32.03.100

HORIZONTAL GIDANCE POWER SUPPLY AS PER SPECN. NO. 7084.32.06.100

HORIZONTAL GIDANCE POWER SUPPLY AS PER SPECN. NO. 7084.32.06.100

7084.32.06.100

PCB PHASE SENSITIVE RECTIFIER AS PER DRG. NO. 7084.32.02.400-01

PCB PHASE SENSITIVE RECTIFIER AS PER DRG. NO. 7084.32.02.400-01

7084.32.02.400-01

PCB ADAPTER AS PER DRG. NO. 7064.03.03.000

PCB ADAPTER AS PER DRG. NO. 7064.03.03.000

DRG. NO. 7064.03.03.000

PCB ADJUSTMENT BOARD AS PER DRG. NO. 7064.03.01.600

PCB ADJUSTMENT BOARD AS PER DRG. NO. 7064.03.01.600

DRG. NO. 7064.03.01.600

PCB CONTROL MODULE OF SMALL SIZE GYRO AS PER DRG. NO. 7194.03.01.000

PCB CONTROL MODULE OF SMALL SIZE GYRO AS PER DRG. NO. 7194.03.01.000

7194.03.01.000

HOSE TO DRG. NO. AK-630 SB-114-17 IN FINISHED CONDITION

AS PER DRAWING

AK-630 SB 114-17

• AS PER ATTACHMENT

• AS PER ATTACHMENT

HOSE TO DRG. NO. AK-630 SB 114-16 IN FINISHED CONDITION

AS PER DRAWING

AK-630 SB 114-16

• As per attachment

• As per attachment

HOSE TO DRG. NO. AK-630 SB 114-14 IN FINISHED CONDITION

AS PER DRAWING

AK-630 SB-114-14

• AS PER ATTACHMENT

• AS PER ATTACHMENT

AS PER DRG. & SPECIFICATION

AS PER DRG. & SPECIFICATION

• As per attachment

• as per attachment

BELLEVILLE SPRING DRG.NO.AK-630.120-4

AS PER DRG

AK 630 120-4

COLLECTOR/MANIFOLD ASSY. AK-630 SB 108 SB

AS PER DRAWING

• As per attached file

• As per attached file

RECEIVER TO DRG, NO. CTM-0108/1 TO CTM-0108/6

AS PER DRAWING

CTM-0108/1 TO CTM-0108/6

SURFACE TREATMENT OPERATION VIZ: NICKEL PLATING (WITH COPPER - UNDER COAT ) TO SPEC BS: 1224-1970 FOLLOWED BY ELECTRO PHORETIC LAQUERING WITH BLACKISH TINGE WITH SOLID CONTENT 9.9 TO 13% AND PH: 5.2 TO 5.6. THICKNESS OF LAQUER 5 TO 6 MICRON ON COMP PB1, PB3, PB6, PB7, PB9, PB10, PB 15, PB23, PB 32, PB39, PB41 & CTM 0099

SURFACE TREATMENT OPERATION VIZ: NICKEL PLATING (WITH COPPER - UNDER COAT ) TO SPEC BS: 1224-1970 FOLLOWED BY ELECTRO PHORETIC LAQUERING WITH BLACKISH TINGE WITH SOLID CONTENT 9.9 TO 13% AND PH: 5.2 TO 5.6. THICKNESS OF LAQUER 5 TO 6 MICRON

• AS PER ATTACHMENT

• AS PER ATTACHMENT

TORSION SPRING TO DRG. NO. CTM-0114 IN F/C

AS PER DRG

CTM-0114

HAMMER TO DRG. NO. CTM-0110/1 TO CTM-0110/6 FOR MODIFIED PISTOL

AS PER DRAWING

CTM-0110 TO CTM-0110/6

SET OF STOCK RT & LT DRG. NO. CTM-0118 & CTM-0117

AS PER DRAWING

CTM-0117 & CTM-0118

MAGAZINE SUB ASSY. TO DRG. NO. CTM-0112 IN F/C

AS PER DRAWING

CTM-0112

RADIATOR & COOLERS 765-03-K6 CONSISTS OF COOLER OIL VEHICULAR 765-03-Cb161, WATER RADIATOR 765-03-Cb178 & COOLER OIL VEHICULAR 765-03-Cb162

765-03-K6

LFG ORDNANCE COMPONENTS AS PER ANNEXURE "G"

LFG ORDNANCE COMPONENTS AS PER ANNEXURE "G"

SPRING FOR LFG ORDNANCE AS PER ANNEXURE "C"

SPRING FOR LFG ORDNANCE AS PER ANNEXURE "C"

STOCK BUTT TO DRG.NO.: 29 P 0038*2 required for 0.315" Sporting Rifle

AS PER DRG.NO.: 29 P 0038*2 required for 0.315" Sporting Rifle

29 P 0038*2

• AS PER DRAWING

• INSPECTION WILL BE CARRIED OUT AFTER RECEIPT OF MATERIAL AT OFT BY GM OR HIS AUTHORIZED REPRESENTATIVE

CONVERSION OF BOLT BREECH FROM FORGING TO TEND DRG.NO 2369 required for 0.315" Sporting Rifle

AS PER TEND DRG.NO 2369 required for 0.315" Sporting Rifle

TEND 2369

SPRING MAIN TO DRG. NO.32-0106 MATERIAL SPRING STEEL, Gr- 4, IS: 4454 (Pt-1)-81

SPRING MAIN TO DRG. NO.32-0106 MATERIAL SPRING STEEL, Gr- 4, IS: 4454 (Pt-1)-81

32-0106

TRIGGER TO DRG. NO. 32-0701 MK-III ALT VERSION 2 MATERIAL: BS 970 Pt.1: 1983 GD. 070 M-55 (BS 970 EN-9)/ALT.MTL.(I.C.)BS3146 PT.-1,1974 TYPE CLASS-8 ALT. MATERIAL FOR MIM COMPONENTS:MIM 4650. C:0.3-0.6%, NI:1.5-2.5%,Cr-0.5% MAX.,Si-0.5%, Mo:0.5% MAX.,Mn:0.3%,

TRIGGER TO DRG. NO. 32-0701 MK-III ALT VERSION 2 MATERIAL: BS 970 Pt.1: 1983 GD. 070 M-55 (BS 970 EN-9)/ALT.MTL.(I.C.)BS3146 PT.-1,1974 TYPE CLASS-8 ALT. MATERIAL FOR MIM COMPONENTS:MIM 4650. C:0.3-0.6%, NI:1.5-2.5%,Cr-0.5% MAX.,Si-0.5%, Mo:0.5% MAX.,Mn:0.3%,

32-0701

HAMMER TO DRG. NO. 32-0601 MK-III,MATERIAL BS 970 PT I 1983 GD:070 M-55(B.S 970 EN-9) ALT.MATERIAL: FROM I.C ROUTE I.C DRG NO.SK-5377R BS 3146 Pt.1-1974. TYPE CLASS-12 Gr.A.

HAMMER TO DRG. NO. 32-0601 MK-III,MATERIAL BS 970 PT I 1983 GD:070 M-55(B.S 970 EN-9) ALT.MATERIAL: FROM I.C ROUTE I.C DRG NO.SK-5377R BS 3146 Pt.1-1974. TYPE CLASS-12 Gr.A.

32-0601

PLATE BODY TO DRG. NO. 32-0501 MK-III MATERIAL:-BS 970 Pt.1: 1983 Gd. 070 M-55 (BS 970 EN-9), FINISH:-ELECTROSTATIC POWDER COATING AFTER ASSY. ALT MATERIAL FROM IC ROUTE:-BS 3146 PT.1 1974 TYPE CLASS-8.

PLATE BODY TO DRG. NO. 32-0501 MK-III MATERIAL:-BS 970 Pt.1: 1983 Gd. 070 M-55 (BS 970 EN-9), FINISH:-ELECTROSTATIC POWDER COATING AFTER ASSY. ALT MATERIAL FROM IC ROUTE:-BS 3146 PT.1 1974 TYPE CLASS-8.

32-0501