WIRE MGSHV 0.5 ZH AS PER SPECN. NO. TU16.505.437-82

WIRE MGSHV 0.5 ZH AS PER SPECN. NO. TU16.505.437-82

WIRE MGTF 0.35 AS PER SPECN. NO. TU16-505-185-71

WIRE MGTF 0.35 AS PER SPECN. NO. TU16-505-185-71

WIRE MPO 0.2 AS PER DRG. NO. TU16-505-339-79

WIRE MPO 0.2 AS PER DRG. NO. TU16-505-339-79

WIRE MGTFE 0.12 TO SPEC NO. TU16-505.185-71

WIRE MGTFE 0.12 TO SPEC NO. TU16-505.185-71

WIRE MGTF 0.2 TO SPEC NO. TU16-505.185-71

WIRE MGTF 0.2 TO SPEC NO. TU16-505.185-71

WIRE MGTF 0.07 AS PER SPECIN NO. TU16-505.185-71

WIRE MGTF 0.07 AS PER SPECIN NO. TU16-505.185-71

TU16-505.185-71

AS PER PARTICULARS: WIDTH: 36/(+2/-0)MM THICKNESS: 4.0MM(MAX MASS/MTR.:78GM(MAX). BREAKING STRENGTH: 2900KG(MIN) CONSTRUCTION OF YARN: WARP- 96.3X3 ie.96.3/1X3 TEX X FOLD: WEFT - 15.7X9. ENDS IN FULL WIDTH: 219 PICKS/DM: 66( BOTHLAYERS). TPM(RANGE):EARP-188-196, WEFT - 168-196. ELONGATION : 18-25%. WEAVE : TUBULAR PLAIN (3 ENDS WORKING AS ONE). HEAT SETTING : TAPE TUBULAR SHOULD HAVE PROPER HEAT SETTING.

AS PER PARTICULARS: WIDTH: 36/(+2/-0)MM THICKNESS: 4.0MM(MAX MASS/MTR.:78GM(MAX). BREAKING STRENGTH: 2900KG(MIN) CONSTRUCTION OF YARN: WARP- 96.3X3 ie.96.3/1X3 TEX X FOLD: WEFT - 15.7X9. ENDS IN FULL WIDTH: 219 PICKS/DM: 66( BOTHLAYERS). TPM(RANGE):EARP-188-196, WEFT - 168-196. ELONGATION : 18-25%. WEAVE : TUBULAR PLAIN (3 ENDS WORKING AS ONE). HEAT SETTING : TAPE TUBULAR SHOULD HAVE PROPER HEAT SETTING.

1- Width(mm) --- 25 mm. Appendix B of IS:3846:1984 2- Mass(gm/mt.)---12(max). Appendix C of IS:3846:1984 3- Ends(in full/width)------ 85+4/-0. IS:1963 4- Picks/cm.--- 20+2/-0 (total picks based on two thread working as one) IS:1963 5- Breaking load(20 cm X full width)("KN.") Minimum--2.4 IS:1969 6- Nature of material--100% Polyster. IS:667 7- pH Value(Cold Method)--6 to 8.5. IS:1390 8- % Water soluble matter(max)-- 1%. IS:3456 9- Weave-- 2/2 Twill weave. Visual

1- Width(mm) --- 25 mm. Appendix B of IS:3846:1984 2- Mass(gm/mt.)---12(max). Appendix C of IS:3846:1984 3- Ends(in full/width)------ 85+4/-0. IS:1963 4- Picks/cm.--- 20+2/-0 (total picks based on two thread working as one) IS:1963 5- Breaking load(20 cm X full width)("KN.") Minimum--2.4 IS:1969 6- Nature of material--100% Polyster. IS:667 7- pH Value(Cold Method)--6 to 8.5. IS:1390 8- % Water soluble matter(max)-- 1%. IS:3456 9- Weave-- 2/2 Twill weave. Visual

TAIL UNIT ASSY OF 100-120 KG AREAL BOMB, DRG NO- RFI SK 9980. CONSISTS OF 01 NO. OF CONE (RFI SK 9976), 04 NOS OF STABILISER FIN (RFI SK 9995), 01 NO OF STABILISER RING ASSY (RFI SK 9975) & 01 NO OF BASE BUSH (RFI SK 9996).

TAIL UNIT ASSY OF 100-120 KG AREAL BOMB, DRG NO- RFI SK 9980. CONSISTS OF 01 NO. OF CONE (RFI SK 9976), 04 NOS OF STABILISER FIN (RFI SK 9995), 01 NO OF STABILISER RING ASSY (RFI SK 9975) & 01 NO OF BASE BUSH (RFI SK 9996).

DRG NO- RFI SK 9980. CONSISTS OF 01 NO. OF CONE (RFI SK 9976), 04 NOS OF STABILISER FIN (RFI SK 9995), 01 NO OF STABILISER RING ASSY (RFI SK 9975) & 01 NO OF BASE BUSH (RFI SK 9996).

ARM SEAR CONNECTING (THROUGH MIM ROUTE) DRG. REF. NO. 1005-003196 AND DRG. NO. RFI. SK. 10118.

ARM SEAR CONNECTING (THROUGH MIM ROUTE) DRG. REF. NO. 1005-003196 AND DRG. NO. RFI. SK. 10118.

DRG. REF. NO. 1005-003196 AND DRG. NO. RFI. SK. 10118.

PLUNGER,LEVER,TRIPPING (THROUGH MIM ROUTE) DRG. REF. NO.1005-003181 AND DRG. NO. RFI. SK. 10127 FOR 9MM AUTO PISTOL

PLUNGER,LEVER,TRIPPING (THROUGH MIM ROUTE) DRG. REF. NO.1005-003181 AND DRG. NO. RFI. SK. 10127 FOR 9MM AUTO PISTOL

DRG. REF. NO.1005-003181 AND DRG. NO. RFI. SK. 10127

LINK,HAMMER (THROUGH MIM ROUTE) DRG. REF. NO. 3040-003489AND DRG. NO. RFI. SK. 10117 FOR 9MM AUTO PISTOL

LINK,HAMMER (THROUGH MIM ROUTE) DRG. REF. NO. 3040-003489AND DRG. NO. RFI. SK. 10117 FOR 9MM AUTO PISTOL

DRG. REF. NO. 3040-003489AND DRG. NO. RFI. SK. 10117

TRIGGER (THROUGH MIM ROUTE) DRG. REF. NO.1005-003184AND DRG. NO. RFI. SK. 10129.FOR 9MM AUTO PISTOL

TRIGGER (THROUGH MIM ROUTE) DRG. REF. NO.1005-003184AND DRG. NO. RFI. SK. 10129.FOR 9MM AUTO PISTOL

DRG. REF. NO.1005-003184AND DRG. NO. RFI. SK. 10129

PLATE LOCKING (THROUGH MIM ROUTE) DRG. REF. NO.1005-003205AND DRG. NO. RFI. SK. 10126

PLATE LOCKING (THROUGH MIM ROUTE) DRG. REF. NO.1005-003205AND DRG. NO. RFI. SK. 10126

DRG. REF. NO.1005-003205AND DRG. NO. RFI. SK. 10126

EJECTOR (THROUGH MIM ROUTE) DRG. REF. NO. 1005-003156 ANDDRG. NO. RFI. SK. 10121 FOR 9MM AUTO PISTOL

EJECTOR (THROUGH MIM ROUTE) DRG. REF. NO. 1005-003156 ANDDRG. NO. RFI. SK. 10121 FOR 9MM AUTO PISTOL

DRG. REF. NO. 1005-003156 ANDDRG. NO. RFI. SK. 10121

SEAR (THROUGH MIM ROUTE)DRG. REF. NO. 1005-003172 ANDDRG. NO. RFI. SK. 10125. FOR 9MM AUTO PISTOL

SEAR (THROUGH MIM ROUTE)DRG. REF. NO. 1005-003172 ANDDRG. NO. RFI. SK. 10125. FOR 9MM AUTO PISTOL

DRG. REF. NO. 1005-003172 ANDDRG. NO. RFI. SK. 10125.

CATCH MAGAZINE (THROUGH MIM ROUTE)DRG. REF. NO.1005-003148AND DRG. NO. RFI. SK. 10123 FOR 9MM AUTO PISTOL

CATCH MAGAZINE (THROUGH MIM ROUTE)DRG. REF. NO.1005-003148AND DRG. NO. RFI. SK. 10123 FOR 9MM AUTO PISTOL

DRG. REF. NO.1005-003148AND DRG. NO. RFI. SK. 10123

LEVER TRIPPING (THROUGH MIM ROUTE) DRG. REF. NO.5340-016094 AND DRG. NO. RFI. SK. 10122 FOR 9MM AUTO PISTOL

LEVER TRIPPING (THROUGH MIM ROUTE) DRG. REF. NO.5340-016094 AND DRG. NO. RFI. SK. 10122 FOR 9MM AUTO PISTOL

DRG. REF. NO.5340-016094 AND DRG. NO. RFI. SK. 10122

IC BLOCK GAS OF 7.62 MM ASSUALT RIFLE GHAATAK, RFI SK. NO.9727*AR (LT.DC. NO. 11E/026/17 DT.25/05/2017

IC BLOCK GAS OF 7.62 MM ASSUALT RIFLE GHAATAK, RFI SK. NO.9727*AR (LT.DC. NO. 11E/026/17 DT.25/05/2017

RFI SK. NO.9727*AR (LT.DC. NO. 11E/026/17 DT.25/05/2017

FORGING OF PISTON EXTENSION FOR 7.62 MM ASSAULT RIFLE AS PERDRG. NO. RFI SK NO.9521

FORGING OF PISTON EXTENSION FOR 7.62 MM ASSAULT RIFLE AS PERDRG. NO. RFI SK NO.9521

DRG. NO. RFI SK NO.9521

I/C BRACKET FORE SIGHT FOR 7.62 MM ASSAULT RIFLE (GHAATAK)DRG. NO. RFI SK-9919AR

I/C BRACKET FORE SIGHT FOR 7.62 MM ASSAULT RIFLE (GHAATAK)DRG. NO. RFI SK-9919AR

RFI SK-9919AR

PISTON (MODIFIED), DRG. NO. AR/07/2-RFI FOR 7.62 ASSAULT RIFLE (GHAATAK).

PISTON (MODIFIED), DRG. NO. AR/07/2-RFI FOR 7.62 ASSAULT RIFLE (GHAATAK).

DRG. NO. AR/07/2-RFI

No.IS:2771 WITH WATER ABSORPTION / COBB TEST

No.IS:2771 WITH WATER ABSORPTION / COBB TEST

• as per attached list (Manufacturing Technology Files )

• as per attached list (Testing / Inspection Facility Files )

Boxes Fibre Board Rigid Corrugated Triple Wall 7 Ply of Size 700mmx450mmx400mm CQA(GS)/US/460

CQA(GS)/US/460

• as per attached list (Manufacturing Technology Files )

• as per attached list (Testing / Inspection Facility Files )

HAND WHEEL ASSY TO DRG.NO.2A46 -CD21-10CD REQUIRED FOR HAND ELEVATING MECH.T-90 -SCOPE OF WORK ATTACHED

HAND WHEEL ASSY TO DRG.NO.2A46 -CD21-10CD REQUIRED FOR HAND ELEVATING MECH.T-90 -SCOPE OF WORK ATTACHED

DRG.NO.2A46 -CD21-10CD

Electronic Point Detonation Fuze for 155 mm as per Annexure ‘A‘ & ‘B’

Electronic Point Detonation Fuze for 155 mm as per Annexure ‘A‘ & ‘B’

IND/TC/4675 & Approved Samples

IND/TC/4675 & Approved Samples

Rope Polypropylene 3 Strands H/Log 6 mm Dia

IND/TC/2324(b)

DC DC CONVERTER TE-SD-100B-12V

DC DC CONVERTER TE-SD-100B-12V

FISCHER CONNECTORS MAKE CA S 104 A092-140+ TERMINATION 1 OTHER END OPEN CABLE SHIELDED 19*28 AWG PUR JACKET COLOUR BLACK LENGTH 1.5 MTR.

FISCHER CONNECTORS MAKE CA S 104 A092-140+ TERMINATION 1 OTHER END OPEN CABLE SHIELDED 19*28 AWG PUR JACKET COLOUR BLACK LENGTH 1.5 MTR.

FISCHER CONNECTORS MAKE DBPU 104 A092-149 PANEL MOUNT RECEPTACLE WITH 19 FEMALE SOLDER BUCKET PINS

FISCHER CONNECTORS MAKE DBPU 104 A092-149 PANEL MOUNT RECEPTACLE WITH 19 FEMALE SOLDER BUCKET PINS

FISCHER CONNECTORS MAKE CA S103 A015-700+ TERMINATION 1 OTHER END FREE TRIAX CABLE LENGTH 3MTR. COLOUR BLACK

FISCHER CONNECTORS MAKE CA S103 A015-700+ TERMINATION 1 OTHER END FREE TRIAX CABLE LENGTH 3MTR. COLOUR BLACK

FISCHER CONNECTORS MAKE DEE 103 A015-700 PANEL MOUNT RECEPTACLE WITH FEMALE SOLDER BUCKET PINS.

FISCHER CONNECTORS MAKE DEE 103 A015-700 PANEL MOUNT RECEPTACLE WITH FEMALE SOLDER BUCKET PINS.

FISCHER CONNECTORS MAKE-4 PIN CONNECTOR CONSISTING OF (A) REAR MOUNTED PANEL RECEPTACLE (UR01W07 F004P BK1 E2AA), (B) SHORT CABLE PLUG (UP01L07 M004S BK1 Z2ZA) & (C) BEND RELIEF (UB07 A1BK DIA1.9)

FISCHER CONNECTORS MAKE-4 PIN CONNECTOR CONSISTING OF (A) REAR MOUNTED PANEL RECEPTACLE (UR01W07 F004P BK1 E2AA), (B) SHORT CABLE PLUG (UP01L07 M004S BK1 Z2ZA) & (C) BEND RELIEF (UB07 A1BK DIA1.9)

FISCHER CONNECTORS MAKE S 104 A092-140 + E3 104.2/5.7 + B19 PIN CONNECTOR.

FISCHER CONNECTORS MAKE S 104 A092-140 + E3 104.2/5.7 + B19 PIN CONNECTOR.

FISCHER CONNECTORS MAKE CA S 103 A015-700 + TERMINATION 1 OTHER END S 103 A015-700 + TRIAX CABLE LENGTH 3MTR COLOUR BLACK, LENGTH 3 METER

FISCHER CONNECTORS MAKE CA S 103 A015-700 + TERMINATION 1 OTHER END S 103 A015-700 + TRIAX CABLE LENGTH 3MTR COLOUR BLACK, LENGTH 3 METER

TEAR TAPE NYLON 44 MM,10000 N(TEARING STRENGTH=340-640 N)

ADRDE/SPECN/1980/4(b)

ADRDE/SPECN/1980/4(b)

• As Per Specification/Drawing

• As Per Specification/Drawing

ADRDE/1984/24

ADRDE/1984/24

TAPE NYLON 26 MM THIN 200 KG O.G.

ADDE/BP/1(B) WITH 20-30% ELONGATION & PROPER HEAT SETTING

• As per Specification/Drawing

• As per Specification/Drawing

SPECN-ADRDE/SPECN/1993/44

SPECN-ADRDE/SPECN/1993/44

ADRDE/1985/27 (b) with proper heat setting

ADRDE/1985/27 (b) with proper heat setting

ADRDE/1992/38 20-30% ELO.WITH PROPER HEAT SETTING

ADRDE/1992/38 20-30% ELO.WITH PROPER HEAT SETTING

ADRDE/1983/13

ADRDE/1983/13

ADDE/BP/1(b)with 20-30% elongation & proper heat setting.

ADDE/BP/1(b)with 20-30% elongation & proper heat setting.

ADDE/BP/1(b) with 20-30 % elongation & proper heat setting

ADDE/BP/1(b) with 20-30 % elongation & proper heat setting

ADDE/BP/1(b)with 20-30% elongation & proper heat setting

ADDE/BP/1(b)with 20-30% elongation & proper heat setting

ADDE/BP/1(b)with 20-30% elongation & proper heat setting

ADDE/BP/1(b)with 20-30% elongation & proper heat setting

ADDE/BP/1(b) with 20-30 % elongation & proper heat setting

ADDE/BP/1(b) with 20-30 % elongation & proper heat setting

TAPE NYLON 26 MM THIN 200 KG Undyed

ADDE/BP/1(b) with 20-30% elongation & proper heat setting

• As per Specification/drawing

• As per Specification/drawing

ADDE/BP/1(b)WITH 20-30% ELONGATION & PROPER HEAT SETTING.

ADDE/BP/1(b)WITH 20-30% ELONGATION & PROPER HEAT SETTING.

TAPE NYLON 26 MM 2150 kgf

Specn. No.- ADRDE/SPECN/70(b), variety No. 1 Page No. 15 of 25 as per No. ADRDE/QMS/TDTM/SPECN/85.

• As per Specn/Drg

• As per Specn/Drg

TAPE TUBULAR NYL 18 MM BS 700 KG U/D

ADRDE/SPECN/1992/38 (b)

• As per Specification/Drawing

• As per Specification/Drawing

AS PER PARTICULARS: WIDTH: 36/(+2/-0)MM THICKNESS: 4.0MM(MAX MASS/MTR.:78GM(MAX). BREAKING STRENGTH: 2900KG(MIN) CONSTRUCTION OF YARN: WARP- 96.3X3 ie.96.3/1X3 TEX X FOLD: WEFT - 15.7X9. ENDS IN FULL WIDTH: 219 PICKS/DM: 66( BOTHLAYERS). TPM(RANGE):EARP-188-196, WEFT - 168-196. ELONGATION : 18-25%. WEAVE : TUBULAR PLAIN (3 ENDS WORKING AS ONE). HEAT SETTING : TAPE TUBULAR SHOULD HAVE PROPER HEAT SETTING.

AS PER PARTICULARS: WIDTH: 36/(+2/-0)MM THICKNESS: 4.0MM(MAX MASS/MTR.:78GM(MAX). BREAKING STRENGTH: 2900KG(MIN) CONSTRUCTION OF YARN: WARP- 96.3X3 ie.96.3/1X3 TEX X FOLD: WEFT - 15.7X9. ENDS IN FULL WIDTH: 219 PICKS/DM: 66( BOTHLAYERS). TPM(RANGE):EARP-188-196, WEFT - 168-196. ELONGATION : 18-25%. WEAVE : TUBULAR PLAIN (3 ENDS WORKING AS ONE). HEAT SETTING : TAPE TUBULAR SHOULD HAVE PROPER HEAT SETTING.

specn.no:-ADRDE/QMS/TDTM/SPECN/93

specn.no:-ADRDE/QMS/TDTM/SPECN/93

ADRDE/1984/24

ADRDE/1984/24

ADDE/BP/1(b)WITH 20-30 % ELONGATION & PROPER HEAT SETTING.

ADDE/BP/1(b)WITH 20-30 % ELONGATION & PROPER HEAT SETTING.

ADRDE/1985/27(a) WITH PROPER HEAT SETTING

ADRDE/1985/27(a) WITH PROPER HEAT SETTING

ADRDE/BP/1(b) with 20-30 % elongation & proper heat setting

ADRDE/BP/1(b) with 20-30 % elongation & proper heat setting

HOLDER,OPTICAL ELEMENT AS PER DRG.NO.:IRDE-335/14

HOLDER,OPTICAL ELEMENT AS PER DRG.NO.:IRDE-335/14

IRDE-335/14

DOVETAIL FEMALE AS PER DRG. NO.CWC-231/2/1

DOVETAIL FEMALE AS PER DRG. NO.CWC-231/2/1

CWC-231/2/1

LOCKING PLATE AS PER DRG.NO.CWC/229/68/1

LOCKING PLATE AS PER DRG.NO.CWC/229/68/1

CWC/229/68/1

SLIDE REAR SIGHT FOR 30-06 SPORTING RIFLE, DRG. NO. TSP-314

BS:970 PT.1 GR 070 M55 OR En-9 TRATMENT:- HRD. & GRD. TO 300-350 H.V.

DRG. NO. TSP-314

L.C FERRO MANGANESE, GRADE:O2FeMn72 PARTICLE SIZE CLASS:5, AS PER IS: 1171-2011, %MN=70-74; %C=0.20 MAX, %SI=1.0 MAX; %S=0.05 MAX; %P=0.30 MAX; PARTICLE SIZE RANGE: 3.12 TO 25MM.

L.C FERRO MANGANESE, GRADE:O2FeMn72 PARTICLE SIZE CLASS:5, AS PER IS: 1171-2011, %MN=70-74; %C=0.20 MAX, %SI=1.0 MAX; %S=0.05 MAX; %P=0.30 MAX; PARTICLE SIZE RANGE: 3.12 TO 25MM.

STEEL ROUND BAR DIA 50 MM X STD LENGTH TO GRADE 40Cr4 Mo3. IS: 5517.

STEEL ROUND BAR DIA 50 MM X STD LENGTH TO GRADE 40Cr4 Mo3. IS: 5517.

Aviation Compressor-performance Testing Machine Terms and conditions as per Annexure A.

Aviation Compressor-performance Testing Machine Terms and conditions as per Annexure A.

AIR COMPRESSOR SET UP FOR TESTING COMPRESSOR

MFG AND SUPPLY OF ROUGH MACHINED BODY TO DRG NO 118 BODY 3400 AS PER SCOPE OF WORK MA 11 110 8 24 DT 15 06 2017

MFG AND SUPPLY OF ROUGH MACHINED BODY TO DRG NO 118 BODY 3400 AS PER SCOPE OF WORK MA 11 110 8 24 DT 15 06 2017

DRG NO 118 BODY 3400 AS PER SCOPE OF WORK MA 11 110 8 24 DT 15 06 2017

SPECN. NO. ADRDE/1159-A-2/SA-6

SPECN. NO. ADRDE/1159-A-2/SA-6

PACK OPENING SPRING ELASTIC 89 MM

ADRDE/781(d)EXCEPT FOR LENGTH

• As per Specification/Drawing

• As per Specification/Drawing

PACK OPENING SPRING ELASTIC 203 MM

ADRDE/781(d)EXCEPT FOR LENGTH

ADRDE/781(d)

• As per Specification/Drawing

• As per Specification/Drawing

PULLY SMALL Prov.Drg. NO. ADRDE/172(b).

Prov. Drg. NO. ADRDE/172(b).

Prov.Drg. NO. ADRDE/172(b).

CATCH ASSY TO PT. NO. ISV-1A

CATCH ASSY TO PT. NO. ISV-1A

CATCH ASSY TO PT. NO. ISV-1A

I/C OF BRACKET BACK SIGHT FOR 7.62MM ASSAULT RIFLE (GHAATAK)AS PER DRAWING NO. RFI SK NO. 9836

I/C OF BRACKET BACK SIGHT FOR 7.62MM ASSAULT RIFLE (GHAATAK)AS PER DRAWING NO. RFI SK NO. 9836

RFI SK NO. 9836

STEEL 32MM(+/-0.50MM)TO SPECN.BS:970 PT-I:1983,GD 708 M40'T'COND. OR EN-19A. V.D IN HR.PILLED & ANNEALED COND(240HV.MAX)MAINTAINED S&P COMBINED 0.022%MAX.TO LENGTH 530MM. WITH NMIRTEST AS PER IS:4163-82. FOR BARREL(NPB),12 BORE(NPB)PAG.

STEEL 32MM(+/-0.50MM)TO SPECN.BS:970 PT-I:1983,GD 708 M40'T'COND. OR EN-19A. V.D IN HR.PILLED & ANNEALED COND(240HV.MAX)MAINTAINED S&P COMBINED 0.022%MAX.TO LENGTH 530MM. WITH NMIRTEST AS PER IS:4163-82. FOR BARREL(NPB),12 BORE(NPB)PAG.

STOCK SIDE RIGHT FOR 9MM AUTO PISTOL 1A, DRG. NO. DS CAT NO-1005-003177

MOULDING POWDER, MOULDING PLASTICS (PHENOLIC) TO SPECN. NO. JSS 1097 GRD. 'Z' WITH A MINIMUM IMPECT STRENGTH OF 0.81 JOULE AND MINIMUM TENSILE STRENGTH OF 41.37 MPa, OR NYLON 66 GP COLOUR BLACK TO SPECN DEF/STAN 93-8/1 WITHOUT GLASS FIBRE FINISH OF END PRODUCT OF STOCK SIDE RIGHT SHALL BE COLOUR BLACK (MATT. FINISH)

DRG. NO. DS CAT NO-1005-003177

STOCK SIDE LEFT FOR 9MM AUTO PISTOL 1A, DRG. NO. DS CAT NO-1005-003176

MOULDING POWDER, MOULDINGPLASTICS (PHENOLIC) TO SPECCN NO. JSS 1097 GRD. "Z" WITH A MINIMUM IMPECT STRENGTH OF 0.81 JOULE AND MINIMUM TENSILE STRENGTH OF 41.37 MPa/ or nylon 66 gp colour black to specn deef/ stan 93-8/1 without glass fibre. finish of end product of stock side left shall be colour black (matt. finish)

DRG. NO. DS CAT NO-1005-003176

MAGAZINE ASSY. FOR 9MM AUTO PISTOL 1A, DRG. NO. DS CAT NO-1005-003190, 1005-003191, 1005-003192

AS PER DRAWING

DRG. NO. DS CAT NO-1005-003190, 1005-003191, 1005-003192

GUIDE SPRING MAIN ASSY FOR 9MM AUTO PISTOL 1A, DRG. NO. DS CAT NO-5360-007390

CROMIUM ALLOY STEEL BALL TO SPECN. IS:2898-1976 H.T./HARDNESS

DRG. NO. DS CAT NO-5360-007390

SLING SUB ASSY. FOR 12 BORE PUMP ACTION GUN, DRG. NO. DS CAT NO-1005-007815, 1005-007994, 1005-007995

AS PER DRAWING

DRG. NO. DS CAT NO-1005-007815, 1005-007994, 1005-007995

SEAR FOR 9MM AUTO PISTOL 1A, DRG. NO. DS CAT NO-1005-003172

IS:3748 : 1990 DESIGNATION 75 T-6

DRG. NO. DS CAT NO-1005-003172

CATCH MAGAZINE FINISH FOR 9MM AUTO PISTOL 1A, DRG. NO. DS CAT NO-1005-003148

BS:970 M40 IS:3748-1990 DESIGNATION 75. T-6

DRG. NO. DS CAT NO-1005-003148