SPECN-ADRDE/SPECN/2002/57 THE TAPE SHALL BE IN CONTINUOUS LENGTH OF 105 M (EXCLUTING SAMPLING ) WITHOUT ANY FLAG OTHERWISE THAT ROLL WILL BE TREATED AS SHORT LENGTH.
Specification
SPECN-ADRDE/SPECN/2002/57 THE TAPE SHALL BE IN CONTINUOUS LENGTH OF 105 M (EXCLUTING SAMPLING ) WITHOUT ANY FLAG OTHERWISE THAT ROLL WILL BE TREATED AS SHORT LENGTH.
SPECN. NO IS: 3255-1979 Reaffirmed 2003. Except that:- a) In appearance finish and in other respectes not defined in this Specn.the material shall conform to the sealed pattern held in the custody of The Controller CQAT&C, Kanpur b)There shall be no presence of starch. (c) Scouring Loss Mild Method is to be followed in lieu of severe method & shall not exceed 2%. (d) (i) Ends in full width to be raised by 2.(ii) Picks/cms(-1) Tolerance to be permitted. (e) In addition the firm shall get their name or trade mark woven/stamped alongwith selvedges at a interval of one meter on either side of the tape (d)sampling plan and criteria AsPer QAI NO.CQATIC/TC-8/11(b)
Specification
SPECN. NO IS: 3255-1979 Reaffirmed 2003. Except that:- a) In appearance finish and in other respectes not defined in this Specn.the material shall conform to the sealed pattern held in the custody of The Controller CQAT&C, Kanpur b)There shall be no presence of starch. (c) Scouring Loss Mild Method is to be followed in lieu of severe method & shall not exceed 2%. (d) (i) Ends in full width to be raised by 2.(ii) Picks/cms(-1) Tolerance to be permitted. (e) In addition the firm shall get their name or trade mark woven/stamped alongwith selvedges at a interval of one meter on either side of the tape (d)sampling plan and criteria AsPer QAI NO.CQATIC/TC-8/11(b)
SPECIFICATION NO.: IS: 3255-1979 Except that :- i) In appearance shade finish and in other respects not
defined in this Specn. the material shall conform to the
sealed pattern held in the custody of the Controller,
CQAT&C, KANPUR. (ii) There shall be no presence of starch (iii) Scouring loss mild method is to be followed in lieu of severe method & shall not exceed 2% (Two percent). (iv) Sampling plan as per annexure (B) attached.
Packing and marking as per schedule No.CIT&C/PMS/65.
Specification
SPECIFICATION NO.: IS: 3255-1979 Except that :- i) In appearance shade finish and in other respects not
defined in this Specn. the material shall conform to the
sealed pattern held in the custody of the Controller,
CQAT&C, KANPUR. (ii) There shall be no presence of starch (iii) Scouring loss mild method is to be followed in lieu of severe method & shall not exceed 2% (Two percent). (iv) Sampling plan as per annexure (B) attached.
Packing and marking as per schedule No.CIT&C/PMS/65
IS : 3255-2024 Except that :-
(i) In appearance shade, finish & in all other respect not defined in this IS Specn. The material shall conform to the sealed pattern held in the custody of the Controller, CQAT&C, Kanpur.
(ii) There shall be no presence of starch.
(iii) Scouring loss Mild method is to be followed in lieu of severs method and shall not exceed 2.0% (Two percent).
(iv) 100% Sampling Testing & Inspection will be resorted to. Sampling plan as per annexure (a) att ached.
Packing and marking as per schedule CIT&C/PMS/65.
SPECIFICATION NO. : ADRDE/SPECN/1993/44(a) ROLL LENGTH 100 MTR. EXCLUDING SAMPLING.
Except that : - Shade should be as per approved sample held with QCM/OPF.
SPECN.NO.: IS:3255-1979 except that :-
(i)In appearance shade finish and in other respects not defined in this Specn. the material shall conform to the
sealed pattern held of the custody of the controller,CQAT&C, Kanpur. (ii)There shall be no presence of strach. (iii)End in full width to be raised by 2. (iv)Pick/cm(-1) Tolerance to be premitted. (v)100% Sampling/testing/inspection shall be resorted to. (vi) Scouring loss-Mild method is to be followed in view of severe method & shall not except 2%(two percent).
(vii) Sampling plan as per annexure (A) attached.
Specification
SPECN.NO.: IS:3255-1979 except that :-
(i)In appearance shade finish and in other respects not defined in this Specn. the material shall conform to the
sealed pattern held of the custody of the controller,CQAT&C, Kanpur. (ii)There shall be no presence of strach. (iii)End in full width to be raised by 2. (iv)Pick/cm(-1) Tolerance to be premitted. (v)100% Sampling/testing/inspection shall be resorted to. (vi) Scouring loss-Mild method is to be followed in view of severe method & shall not except 2%(two percent).
(vii) Sampling plan as per annexure (A) attached.
1--Width(mm) ---12.7 mm. Appendix B of IS:3846:1984
2--Mass(gm/mt.)--- 8(max). Appendix C of IS:3846:1984
3--Ends in full/width)--- 60+3/-0. IS:1963
4--Picks/cm --- 20+2/-0 (total picks based on two thread working as one. IS:1963
5--Breaking load(20 cm X Full width)("KN.") Minimum-- 1.5 IS:1969
6--Nature of material-- 100% Polyster. IS:667
7--pH Value (Cold Method)--6 to 8.5. IS:1390
8--% Water soluble matter (max)---1%. IS: 3456
9--Weave--- 2/2 Twill weave. Visual
Specification
1--Width(mm) ---12.7 mm. Appendix B of IS:3846:1984
2--Mass(gm/mt.)--- 8(max). Appendix C of IS:3846:1984
3--Ends in full/width)--- 60+3/-0. IS:1963
4--Picks/cm --- 20+2/-0 (total picks based on two thread working as one. IS:1963
5--Breaking load(20 cm X Full width)("KN.") Minimum-- 1.5 IS:1969
6--Nature of material-- 100% Polyster. IS:667
7--pH Value (Cold Method)--6 to 8.5. IS:1390
8--% Water soluble matter (max)---1%. IS: 3456
9--Weave--- 2/2 Twill weave. Visual
1- Width(mm) --- 25 mm. Appendix B of IS:3846:1984
2- Mass(gm/mt.)---12(max). Appendix C of IS:3846:1984
3- Ends(in full/width)------ 85+4/-0. IS:1963
4- Picks/cm.--- 20+2/-0 (total picks based on two thread working as one) IS:1963
5- Breaking load(20 cm X full width)("KN.") Minimum--2.4 IS:1969
6- Nature of material--100% Polyster. IS:667
7- pH Value(Cold Method)--6 to 8.5. IS:1390
8- % Water soluble matter(max)-- 1%. IS:3456
9- Weave-- 2/2 Twill weave. Visual
Specification
1- Width(mm) --- 25 mm. Appendix B of IS:3846:1984
2- Mass(gm/mt.)---12(max). Appendix C of IS:3846:1984
3- Ends(in full/width)------ 85+4/-0. IS:1963
4- Picks/cm.--- 20+2/-0 (total picks based on two thread working as one) IS:1963
5- Breaking load(20 cm X full width)("KN.") Minimum--2.4 IS:1969
6- Nature of material--100% Polyster. IS:667
7- pH Value(Cold Method)--6 to 8.5. IS:1390
8- % Water soluble matter(max)-- 1%. IS:3456
9- Weave-- 2/2 Twill weave. Visual
HEIDENHAIN MAKE ENCODER TYPE ERN 1387.001-2048 B4 5V +/- 5%, ID.NR.312 215-14, 1.1V SS OR COMPATIBLE UNIT TYPE: ERN 1387X2048 ID:385487-51 OR EQUIVALENT SIEMENS MAKE ACCEPTABLE
Specification
HEIDENHAIN MAKE ENCODER TYPE ERN 1387.001-2048 B4 5V +/- 5%, ID.NR.312 215-14, 1.1V SS OR COMPATIBLE UNIT TYPE: ERN 1387X2048 ID:385487-51 OR EQUIVALENT SIEMENS MAKE ACCEPTABLE
HEIDENHAIN MAKE ENCODER TYPE ERN 1381.001-2048, W8 5V +/- 5% ID.NR.313 453-02,1V SS OR COMPATIBLE UNIT TYPE:ERN 1381X2048 ID:385489-56 OR EQUIVALENT SIEMENS MAKE ACCEPTABLE .
Specification
HEIDENHAIN MAKE ENCODER TYPE ERN 1381.001-2048, W8 5V +/- 5% ID.NR.313 453-02,1V SS OR COMPATIBLE UNIT TYPE:ERN 1381X2048 ID:385489-56 OR EQUIVALENT SIEMENS MAKE ACCEPTABLE .
ABSOLUTE SEALED LINEAR ENCODER/SCALE, TYPE LC493F; 50NM, ID 557644-04, MEASURING LENGTH 220MM, ACCURACY GRADE, MEASURING STEP1: 12.5000NM, MEASURING STEP2: 50.0000NM, OR SUCCESSOR LC495F, ID 760932-04, WITH SCANNING HEAD AND END BLOCK+MOUNT ING SPAR, MAKE: HEIDENHAIN
Specification
ABSOLUTE SEALED LINEAR ENCODER/SCALE, TYPE LC493F; 50NM, ID 557644-04, MEASURING LENGTH 220MM, ACCURACY GRADE, MEASURING STEP1: 12.5000NM, MEASURING STEP2: 50.0000NM, OR SUCCESSOR LC495F, ID 760932-04, WITH SCANNING HEAD AND END BLOCK+MOUNT ING SPAR, MAKE: HEIDENHAIN
HYDRAULIC OIL FILTER LF.1001 ELEMENT INTERNORMAN MODEL: 01. .NR 1000.6VG.10.B.P. PART NO:305449 EQUIVALLENT MAKE OF HYDA C, INTERNORMAN, PARKAR ARE ACCEPTABLE, SUBJECTED TO FITMENT GUARANTEE ON MACHINE
Specification
HYDRAULIC OIL FILTER LF.1001 ELEMENT INTERNORMAN MODEL: 01. .NR 1000.6VG.10.B.P. PART NO:305449 EQUIVALLENT MAKE OF HYDA C, INTERNORMAN, PARKAR ARE ACCEPTABLE, SUBJECTED TO FITMENT GUARANTEE ON MACHINE
RETURN LINE HYDRAULIC OIL FILTER ELEMENT INTERNORMAN MODEL: 01.E.360.10VG.30.E.P. PART NO:300231, EQUIVALLENT MAKE OF HYDAC, INTERNORMAN, PARKAR ARE ACCEPTABLE, SUBJECTED TO FITM ENT GUARANTEE ON MACHIN
Specification
RETURN LINE HYDRAULIC OIL FILTER ELEMENT INTERNORMAN MODEL: 01.E.360.10VG.30.E.P. PART NO:300231, EQUIVALLENT MAKE OF HYDAC, INTERNORMAN, PARKAR ARE ACCEPTABLE, SUBJECTED TO FITM ENT GUARANTEE ON MACHIN
HIGH PRESSURE HYDRAULIC OIL FILTER HP.601.ELEMENT INTERNORME N MODEL- 01.E 600.10VG.30.E.P. PART NO-300265, EQUIVALLENT MAKE OF HYDAC, INTERNORMAN, PARKAR ARE ACCEPTABLE, SUBJECTED TO FITMENT GUARANTEE ON MACHINE
Specification
HIGH PRESSURE HYDRAULIC OIL FILTER HP.601.ELEMENT INTERNORME N MODEL- 01.E 600.10VG.30.E.P. PART NO-300265, EQUIVALLENT MAKE OF HYDAC, INTERNORMAN, PARKAR ARE ACCEPTABLE, SUBJECTED TO FITMENT GUARANTEE ON MACHINE
Drawing no.
Manufacturing Technology
Testing / Inspection Facility
20
30
Number
31445
RFI/REGD/ESTT./IC/2018
Rifle Factory Ishapur
The General Manager,
Ishapore
Ishapore
West Bengal
743144
INVESTMENT CASTING OF BRACKET(WITH HEAT TREATMENT)AS PER RFI SK.NO.6756*3-S(I.C TO BE SUPPLIED IN HARDNESS RANGE OF 248 TO 280 HB.) FOR RIFLE 5.56MM.INSAS.
Specification
bs
Drawing no.
AS PER RFI SK.NO.6756*3-S(I.C TO BE SUPPLIED IN HARDNESS RANGE OF 248 TO 280 HB.)