STEEL SQUARE 36X36MM (ROUND CORNER 0.5MM MAX.)X 600MM LONG (+3MM/-0MM) HOT ROLLED TO SPECN. BS970 PT-1, 1983, GRD.709 M-40 (EN-19) PERPENDICULARITY SHOULD BE LIMITED TO 0.5MM ON EACH PARTED FACE. MATERIAL TO BE SUPPLIED IN 'T' CONDITION WITH HARDNESS RANGE 250-280 HB (MAX.)
Specification
STEEL SQUARE 36X36MM (ROUND CORNER 0.5MM MAX.)X 600MM LONG (+3MM/-0MM) HOT ROLLED TO SPECN. BS970 PT-1, 1983, GRD.709 M-40 (EN-19) PERPENDICULARITY SHOULD BE LIMITED TO 0.5MM ON EACH PARTED FACE. MATERIAL TO BE SUPPLIED IN 'T' CONDITION WITH HARDNESS RANGE 250-280 HB (MAX.)
STEEL ROD 25MM DIA.(+0.3MM-0.0MM)TO SPCN.BS970 PT-I,1983,GRD709 M-40(EN-19)IN HR.,ANNEALED & PEELED COND IN EXACT LENGTHOF 442MM(+5MM-0.0MM)EACH PIECE,STRAIGHTNES 0.3MM OVER LENGTHVACUUM DEGASSED.MATERIAL REQUIRED FOR CYLINDER GAS TO DRG.NO1005-560066(LT.DC-25824-SA).FOR RIFLE 5.56MM.INSAS
Specification
STEEL ROD 25MM DIA.(+0.3MM-0.0MM)TO SPCN.BS970 PT-I,1983,GRD709 M-40(EN-19)IN HR.,ANNEALED & PEELED COND IN EXACT LENGTHOF 442MM(+5MM-0.0MM)EACH PIECE,STRAIGHTNES 0.3MM OVER LENGTHVACUUM DEGASSED.MATERIAL REQUIRED FOR CYLINDER GAS TO DRG.NO1005-560066(LT.DC-25824-SA).FOR RIFLE 5.56MM.INSAS
REGULATOR GAS. TO D S CAT NO.1005-007746 (DC-26518-SA)FOR RIFLE 5.56MM.INSAS.(TP TO CONFORM 300-350 HV AFTER H & T.MACRO ETCH TEST AS PERASTME 381-84 WITH ACCEPTANCE STD.C2,R2,S2 FOR PLATE -I & NILFOR PLATE II).
Specification
REGULATOR GAS. TO D S CAT NO.1005-007746 (DC-26518-SA)FOR RIFLE 5.56MM.INSAS.(TP TO CONFORM 300-350 HV AFTER H & T.MACRO ETCH TEST AS PERASTME 381-84 WITH ACCEPTANCE STD.C2,R2,S2 FOR PLATE -I & NILFOR PLATE II).
TRIGGER(FINISH) TO DS.CAT NO 1005-003184 (DC-25575-SA) [MACROETCH TEST WILL BE AS PER COL.(D) OF SL.NO.1 OF CQA(SA)NOTE SHEET NO.1] FOR PISTOL AUTO 9MM 1A.
Specification
TRIGGER(FINISH) TO DS.CAT NO 1005-003184 (DC-25575-SA) [MACROETCH TEST WILL BE AS PER COL.(D) OF SL.NO.1 OF CQA(SA)NOTE SHEET NO.1] FOR PISTOL AUTO 9MM 1A.
BAYONET 1A FOR RIFLE 5.56MM WEAPON TO 1005-007812 (DC-26521-SA) AND CQA(SA)SK-992(DC-26469-SA) & CQA(SA)SK-993 (DC-26469-SA).(COMPLETE ASSY.). FOR RIFLE 5.56MM INSAS.
Specification
BAYONET 1A FOR RIFLE 5.56MM WEAPON TO 1005-007812 (DC-26521-SA) AND CQA(SA)SK-992(DC-26469-SA) & CQA(SA)SK-993 (DC-26469-SA).(COMPLETE ASSY.). FOR RIFLE 5.56MM INSAS.
Drawing no.
TO 1005-007812 (DC-26521-SA) AND CQA(SA)SK-992(DC-26469-SA) & CQA(SA)SK-993 (DC-26469-SA).(COMPLETE ASSY.).
BLANK FOR BARREL EXTENSION(UPTO OPERATION STAGE-V)TO RFI SK.NO. 6379*6-S. FOR RIFLE 5.56MM.INSAS. (MATERIAL WILL BE PROVIDED BY RIFLE FACTORY, ISHAPORE)
Specification
BLANK FOR BARREL EXTENSION(UPTO OPERATION STAGE-V)TO RFI SK.NO. 6379*6-S. FOR RIFLE 5.56MM.INSAS. (MATERIAL WILL BE PROVIDED BY RIFLE FACTORY, ISHAPORE)
F/COMPT EJECTOR SMALL ARMS CARTRIDGE DRG.NO.2689/1,SHT-5 TODS CAT NO.1005-007905(DC-26518-SA)THROUGH MIM ROUTE FOR RIFLE 5.56MM INSAS.MACRO ETCH TEST TO CONFORM ASTM381-84STD.C2R2S2 FOR PLATE 1&NIL FOR PLATE 2.NMIR TEST AS PER IS4163-82WITH ACCEPT.STD.3FOR THIN SERIES & 1FOR THICK SERIES OF A,B,C,D
Specification
F/COMPT EJECTOR SMALL ARMS CARTRIDGE DRG.NO.2689/1,SHT-5 TODS CAT NO.1005-007905(DC-26518-SA)THROUGH MIM ROUTE FOR RIFLE 5.56MM INSAS.MACRO ETCH TEST TO CONFORM ASTM381-84STD.C2R2S2 FOR PLATE 1&NIL FOR PLATE 2.NMIR TEST AS PER IS4163-82WITH ACCEPT.STD.3FOR THIN SERIES & 1FOR THICK SERIES OF A,B,C,D
FLASH ABSORBER (WITHOUT PHOSPHATING)TO RFI.SK.-7770-S{DS CATNO.1005-007739(DC-24638-SA)}.NMIR TEST ASPER IS:4163-82 WITHACCEPTANCE STD.BETTER THAN 3(THIN)& 1(THICK)FOR A,B,C,D &MACRO ETCH TEST ASPER ASTME-381-84 WITH ACCPT.LIMIT C2 R2 S2FOR PLT.1&NILFOR PLT.2.TP TO BE CONFORM 250 TO300HV AFTER HT
Specification
FLASH ABSORBER (WITHOUT PHOSPHATING)TO RFI.SK.-7770-S{DS CATNO.1005-007739(DC-24638-SA)}.NMIR TEST ASPER IS:4163-82 WITHACCEPTANCE STD.BETTER THAN 3(THIN)& 1(THICK)FOR A,B,C,D &MACRO ETCH TEST ASPER ASTME-381-84 WITH ACCPT.LIMIT C2 R2 S2FOR PLT.1&NILFOR PLT.2.TP TO BE CONFORM 250 TO300HV AFTER HT
EXTRACTOR SMALL ARMS CARTRIDGE TO D.S. CAT NO.1005-007756 (DC-26658-SA DT.01/08/12 (THROUGH MIM ROUTE)MACRO ETCH TEST TO CONFORM ASTME 381-84 STD.C2R2S2 FOR PLATE 1&NIL FOR PLATE2.NMIR TEST AS PER IS:4163-82WITH ACCEPTANCE STD.3 FOR THIN & 1 FOR THICK SERIES OF A,B,C,D. FOR RIFLE 5.56MM.INSAS.
Specification
EXTRACTOR SMALL ARMS CARTRIDGE TO D.S. CAT NO.1005-007756 (DC-26658-SA DT.01/08/12 (THROUGH MIM ROUTE)MACRO ETCH TEST TO CONFORM ASTME 381-84 STD.C2R2S2 FOR PLATE 1&NIL FOR PLATE2.NMIR TEST AS PER IS:4163-82WITH ACCEPTANCE STD.3 FOR THIN & 1 FOR THICK SERIES OF A,B,C,D. FOR RIFLE 5.56MM.INSAS.
TUBE LOWER TO DRG.NO.ARDE SK 2975/11. FOR RIFLE 5.56MM INSAS FOLDABLE BUTT(STEEL).[AL.ALLOY TO IS:738-243451'W'(HT15-OLD DESIG)WITH PROTECTIVE FINISH ANODISED TO COLOUR BLACK].
Specification
TUBE LOWER TO DRG.NO.ARDE SK 2975/11. FOR RIFLE 5.56MM INSAS FOLDABLE BUTT(STEEL).[AL.ALLOY TO IS:738-243451'W'(HT15-OLD DESIG)WITH PROTECTIVE FINISH ANODISED TO COLOUR BLACK].