Specification : CORRUGATED FIBRE BOARD BOXES(PROVI)OF INTERNAL DIMENSIONS 400 MM X 400 MM X 600 MM,SPCN.NO.OFI/ 100/NIGU/SPCN,ISSUE NO-2 (TWO) DT. 27-11-2010 & AS PER DRG. NO.OFI/2010/NIGU/297 R1.
R
Estab
Category : ddp
Grade : 1
Size :
S
1Ordnance Equipment Factory
[ENR Registration]
Name
Specification
Use
Status
1) BOX CORRUGATED VARIOUS
Description : BOX CORRUGATED VARIOUS()
Specification : AS PER REQUIREMENT & SPECIFICATION
4) CASE ASSY OF 9MM MAGAZINE IN FINISHED CONDITION
Description : CASE ASSY OF 9MM MAGAZINE IN FINISHED CONDITION()
Specification : CASE ASSY OF 9MM MAGAZINE IN FINISHED CONDITION AS PER DRG DS CAT NO. 1005-000970 (INCLUDING COMPONENT PLATE BACK 1005-000971, PLATE FRONT 1005-000972, PLATE SIDE L/H 1005-000973, PLATE SIDE R/H 1005-000974, STOP 1005-000975 DC (I) 25681
C
Estab
5) WASHER KEY FOR MAG
Description : WASHER KEY FOR MAG()
1) STEEL BLANK OF CYLINDER GAS TO DRG NO SKM 889 WITHOUT HEAT TREATMENT
Description : STEEL BLANK OF CYLINDER GAS TO DRG NO SKM 889 WITHOUT HEAT TREATMENT()
Specification : STEEL BLANK OF CYLINDER GAS TO DRG. NO. SKM- 889 WITHOUT HEAT TREATMENT (STEEL FORGING SKM- 306*3 LF NO. 0144079003 TO BE ISSUED BY SAF AGAINST B/G)
1) ST STRIP FOR LMG
Description : ST STRIP FOR LMG()
Specification : ST. STRIP 1.8 MM THICK X 72 MM X 1050 MM LENGTH WITH GRAINS IN LENGTH-WISE DIRECTION TO SPECN. STEEL IS:7226-1974,DESIGNATION C 40 (FOR BRACKET FRONT).
Specification : STARCH GR II AMMUNITION TO SPECN :IND/ME/459 (C) 2496-ME DT 4-2-84.
R
Estab
2) SILICA GEL BAGS WEIGHING 4 POINT 5 GMS PLUS MINUS ZERO POINT FIVE GMS ITEM CODE 1003250138
Description : SILICA GEL BAGS WEIGHING 4 POINT 5 GMS PLUS MINUS ZERO POINT FIVE GMS ITEM CODE 1003250138()
Specification : SILICA GEL BAGS WEIGHING 4.5GMS (+/-) 0.5GMS CONTAINING SILICA CRYSTALS/GEL OF SIZE 1.00 MM TO 2.00 MM TO SPECN. IS-3401-1992 (THIRD REVISION) (REAFFIRMED 1997) NORMAL TYPE DIMENSION OF BAGS AS PER DRG.NO. khPK-210025 a (ITEM 6)
Specification : PACKING FITMENTS CONSISTING OF ONE NO.EACH OF THE FOLLOWING:1.BOTTOM TO DRG. PT. NO: ISV-1976 DC-36073-A DT 31/01/96.2.TOP TO DRG. PT. NO. : ISV-1975 DC-36073-A DT 31/01/96.
Specification : BRASS STRIP 28 +/-0.2 MM WIDE X 0.5+0.02 MM THICK IN COIL OF CONTINUOUS LENGTH TO SPECN.BS-2870-1980,DESIG.CZ102,1/2H.HARDNESS 100-115 VPN.MAT.MUST BE HOMOGENEOUS,FREE FROM BURRS BOWINESS (MAX) 2MM/MTR.COIL WT.35-40KG,ID WITH NYLON RING30
Specification : BRASS STRIP 20+/-0.50 MM WIDE X 0.497+/- 0.020 MM THICK IN COIL OF 8 METERS MINIMUM. TO SPECN:-BS-2870-1980, CZ-102,HALF HARD, HARDNESS 100-115 VPN
Specification : BRASS STRIP 24 X 0.457 (+/-0.02) MM TO SPECN.IS:410-1977 (THIRD REVISION)(REAFFIRMED 2006) AMENDMENT NO.1 APRIL 1981DESIG.Cu Zn 30 IN ANNEALD CONDITION.
Specification : BRASS STRIP 14.5+/-0.5MM WIDE X 0.69 -0.02MM THICK TO SPECN.BS-2870 CZ-106 1/4 HARD. MATERIAL TO BE SUPPLIED IN COILS OF CONTINOUS LENGTH WEIGHT OF EACH COIL TO BE BETWEEN 10 TO 15KGS WITH INSIDE DIA OF COIL 150MM(MAX.) HARDNESS HV 75 TO
R
Estab
5) BRASS STRIP 22X1.02 MM (ITEM CODE: 0710664345)
Description : BRASS STRIP 22X1.02 MM (ITEM CODE: 0710664345)()
Specification : BRASS STRIP 22+/-0.5MM WIDE x1.02+/-0.025MM THICK TO SPECN BS-2870-CZ-106 1/4 HARD. MATERIAL TOBE SUPPLIED IN COILS OFCONTINOUS LENGTH WEIGHT OF EACH COIL TO BE BETWEEN 10 T0 15 KG WITH INSIDE DIA OF COIL 70 TO 100MM,HARDNESS H.V.75 TO 90
Specification : BRASS STRIP 24+/-0.20 MM WIDE X 0.70+0.02 MM THICK IN COIL OF CONTINUOUS LENGTH TO SPECN:JSS-9535-02-2008(REV.NO.3)HARDNESS 75-90HV.MAT.MUST BE HOMOGENEOUS,FREE FROM BURRS,BOWINESS (MAX) 2MM/MTR.COIL WT 35-40KG,ID WITH NYLON RING300MM MIN
Specification : BRASS STRIP 22+/-0.50 MM WIDE X 0.7 +0.02/-0.03 MM THICK IN COILS OF CONTINUOUS LENGTH WEIGHING 10 TO 15 KG AND INSIDE DIA. OF COIL 100 TO 150 MM TO SPECN BS-2870 CZ 106 1/4 HARD
Specification : BRASS STRIP 48 +/-0.40mm WIDE X 1.1 +/-0.02mm THICK IN COLD ROLLED CONDITION LENGTH 3 METRES IN COIL MIN SPECN : BS-2870 CZ-108, BRINELL HARDNESS : 80 - 120
R
Estab
11) BRASS STRIP 132X0.4MM IS410 ZN30 O (0712590132)
Description : BRASS STRIP 132X0.4MM IS410 ZN30 O (0712590132)()
Specification : BRASS STRIP 132+/- 0.5 MM WIDE X 0.4 +/-0.025MM THICK TO SPECN.IS 410-1977 (REAFFIRMED 2006) (THIRD REVISION) WITHAMENDMENT NO.1 APRIL 1981 Cu Zn 30 CONDITION ANNEALED INCOIL. WEIGHT OF COIL NOT THAN 30 KG. I/D MINIMUM 100 MM.
R
Estab
12) BRASS STRIP 127X0.4MM IS410 ZN30 O (0712590159)
Description : BRASS STRIP 127X0.4MM IS410 ZN30 O (0712590159)()
Specification : BRASS STRIP 127+/-0.5 MM WIDE X 0.4+/- 0.025MM THICK IN COILS OF 3 MTR LENGTH MIN. I/D OF COIL BE 75 MM SPECN:IS-410-1977 (Reaffirmed 2006) (THIRD REVISION) WITH AMENDMENT NO.1APRIL-1981, CU ZN 30 CONDITION O (ANNEALED)
Specification : COPPER ALLOY STRIP 31.75 +/ -0.50 MM WIDE X 1.448+/- 0.025MMTHICK IN LENGTH OF 3 METERS IN COILS TO SPECN.IS -3167-1982(FIRST REVISION) REAFFIRMED DEC-98.HARDNESS 55-75 HV.
Specification : BRASS STRIP 28.0+/-0.5 X 0.57+/-0.02 MM THICK TO SPECN. JSS-9535-02-2008(REVISION NO.3) HARDNESS 135-155 HV IN THEFORM OF COIL OF 60MM INT.DIA.
Specification : BRASS STRIP 102 +/-0.5 MM WIDE X 3.66 +/-0.05 MM THICK IN LENGTH OF 2.5 TO 3 METERS TO SPECN:BS2871 PART 2:1972:CZ126 CONDITION M (STRESS RELIEVED) OR JSS 9535-02:2008(REVISION NO.3)(ANNEALED).
Specification : BRASS STRIP 70+/-0.8 MM WIDE x 2.29+/-0.05 MMTHICK IN LENGTHOF 3 METERS IN COILS TO SPECN.JSS-9535-02-2008 REVISON NO.3IN ANNEALED COND.
R
Estab
19) BRASS STRIP 25.4X0.63 MM (0717560949)
Description : BRASS STRIP 25.4X0.63 MM (0717560949)()
Specification : BRASS STRIP 25.4+/-0.50mm WIDEx0.63+/-0.038mm THICK(1"x24BG)TO SPECN:JSS-9535-02-2008 (Rev. NO-3),(i)GRAIN SIZE 0.065MMMax.(ii)STRIP TO BE IN ANNEALED CONDITION HAVING HARDNEES BETWEEN 70 - 90 VPN, (iii)MAT TO BE SUPPLIED IN COILS OF ID 1
Specification : BRASS STRIP 60.32 + 0.50 MM WIDE X 0.315 +/- 0.0254 MM THICK ANNEALED HARDNESS 78 VPN MARK TO SPECN:IS-410-1977,CuZn 30CONDITION (a)(REAFFIRMED 2006)(THIRD REVISION)WITH AMENDMENT NO.1 APRIL 1981.
10) PSL FOR IDENTIFICATION OF PACK COVER OF ECAD PARAPRINTED 142 CM V.NO.4
Description : CLOTH DRILL COTTON DISRUPTIVE PATTERN VAT PRINTED 142 CM V.NO.4()
Specification : AS PER SPECIFICATION
R
Estab
11) PSL FOR IDENTIFICATION COMPLETE WITH PACK OF ECAD()
Specification : AS PER SPECIFICATION
R
Estab
12) WASHING INSTRUCTION LABEL()
Specification : AS PER SPECIFICATION
R
Estab
13) P.S.L BILINGUAL FOR NET MOSQUITO RM POLYESTER FR
Description : Fabrication of Net Mosquito Flam Retardant White()
Specification : AS PER SPECIFICATION
R
Estab
14) POLYTHENE BAG SIZE W-39 CM X L- 73 CM, 0.04 MM THICK()
1) PAINT PRIMING REDOXIDE ZINC CHROME AMMN AIR DRYING MATT FINISH BRUSHING or SPRAYING
Description : PAINT PRIMING REDOXIDE ZINC CHROME AMMN AIR DRYING MATT FINISH BRUSHING or SPRAYING()
2) READY MIXED PAINT AIR DRYING SEMI GLOOSY TYPE SPRAYING TO SPECN. IS:168:1993 (REAFFIRMED 2002) WITH INDIAN STANDARD COLOUR NO.359, COLOUR SHADE-MIDDLE BUFF TO SPEC.IS:5-2004
Description : READY MIXED PAINT AIR DRYING SEMI GLOOSY TYPE SPRAYING TO SPECN. IS:168:1993 (REAFFIRMED 2002) WITH INDIAN STANDARD COLOUR NO.359, COLOUR SHADE-MIDDLE BUFF TO SPEC.IS:5-2004()
Specification : READY MIXED PAINT AIR DRYING SEMI GLOOSY TYPE SPRAYING TO SPECN. IS:168:1993 (REAFFIRMED 2002) WITH INDIAN STANDARD COLOUR NO.359, COLOUR SHADE-MIDDLE BUFF TO SPEC.IS:5-2004
E
Estab
3) APC 221 AS PER SPECIFICATION 1011704021
Description : APC 221 AS PER SPECIFICATION 1011704021()
Specification : APC 221 to Specn JSS 8010-28:2015(Rev-No.3) OR
Specn JSS 8010-68:2014(Rev.No.3) Paint Ready Mixed Priming Red Oxide Zinc Chrome, Ammn., Air drying Matt Finish, Brushing/Spraying.
E
Estab
4) PAINT RFU BLACK ACID PROOF
Description : PAINT RFU BLACK ACID PROOF()
1) STEEL ROUND TO SPECN IS 7283 1992 WITH PROPERTIES AS PER SPECN IS 2062 2006 AND SIZE 115 MM DIA
Description : STEEL ROUND TO SPECN IS 7283 1992 WITH PROPERTIES AS PER SPECN IS 2062 2006 AND SIZE 115 MM DIA()
Specification : STEEL ROUND TO SPECN. IS:7283-1992 WITH PROPERTIES AS PER SPECN IS 2062-2006 DESIGNATION (FE 410 W) QUALITY-A HAVING STRAIGHT LENGTH OF 2 TO 3 METERS. SIZE: - 115.00 +2.00 MM DIA
R
Estab
Category : ddp
Grade : 1
Size :
S
1Field Gun Factory Kanpur
[ENR Registration]
Name
Specification
Use
Status
1) BRONZE FORGING FOR SHELL & SAFETY ARM
Description : BRONZE FORGING FOR SHELL & SAFETY ARM()
Specification : AL-BRONZE FORGING 75MM X 45MM IN MULTI
1) AMPOULE RESERVE BATTERY AS PER MTPF DRG NO 770 22 33 00 I AMPOULE BATTERY VITZROCELL VCG1525 10 XX
Description : AMPOULE RESERVE BATTERY AS PER MTPF DRG NO 770 22 33 00 I AMPOULE BATTERY VITZROCELL VCG1525 10 XX()
Specification : AMPOULE RESERVE BATTERY AS PER MTPF DRG.NO.770-22-33-00 i.e. AMPOULE BATTERY VITZROCELL VCG1525 10-XX
C
Estab
Category : ddp
Grade : 1
Size :
L
4399
SK Dynamics Pvt.Ltd.
B 5 Industrial Estate Near Ram Nagar Roorkee Uttarakhand
PIN1 : 247667
Phone No. : 263616 GSTIN :
05AAKCS1322G1ZP
33) FINISH MACHINING OF VARIOUS COMPONENTS INVOLVING PRECISION MACHINING AND SUBASSEMBIES, SSEMBLIES THE
Description : FINISH MACHINING OF VARIOUS COMPONENTS INVOLVING PRECISION MACHINING AND SUBASSEMBIES, SSEMBLIES THE()
