Specification : STEEL ROUND 18.00 MM TO SPECN. BS:970PT.1:1983
GD.655 M13 (EN 36B).(FOR STUD CHANGE LEVER).
R
Estab
Category : s
Grade : 3
Size :
S
1Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) STEEL SHEET
Description : STEEL SHEET()
Specification : STEEL SHEET 13 SWG (2.337MM)X1000X2500MM IN COLD ROLLED
AND ANNEALED CONDITION TO SPECN. BS:1449:PT.1:1983.GR.CS-3
SEC.2 OR IS:513:1994 GR.DD.
R
Estab
Category : s
Grade : 3
Size :
S
1Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) STEEL SHEET Point 9MM 20SWG X 1000 X 1500MM
Description : STEEL SHEET Point 9MM 20SWG X 1000 X 1500MM()
Specification : STEEL SHEET 0.9MM (20SWG) X 1000 X 1500MM ,STEEL IS:1570 (PART-2/SEC-1): 1979 10C4 OR BS:1449
PART-3A) : 1964 GD HS-12 FOR STRIKER AS PER DRG NO. NAD
7606/2.
R
Estab
2) SM SHEET CR
Description : SM SHEET CR()
Specification : SM SHEET CR 1.25X1250X2500MM BS:1449:PT.1:1983 CR-3 SEC.2
OR IS:513:1994 REQD.FOR STOP D S CAT NO 1005-000975 9MM
MAGZINE CARBINE 1A1/CARBURIZING BOX.
R
Estab
3) SM SHEET CR 16 SWG
Description : SM SHEET CR 16 SWG()
Specification : SM SHEET CR 16 SWG TO SPECIFICATION BS 1449:PT.1:1983 CS-3 SEC.2 OR IS:513:1994 DD (SIZE 1.6X1287X2500 OFCR SHEET)
R
Estab
Category : s
Grade : 3
Size :
S
1Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) Steel Round Dia 10mm
Description : Steel Round Dia 10mm()
Specification : STEEL ROUND DIA 10MM SPEC. IS:7283-1974 GD C40
Specification : STEEL ROUND 18.00 MM TO SPECN. BS:970PT.1:1983
GD.655 M13 (EN 36B).(FOR STUD CHANGE LEVER).
R
Estab
Category : s
Grade : 3
Size :
S
1Ordnance Factory Kanpur
Name
Specification
Use
Status
1) C.R. Bright Annealed steel strip size 1.05mm (+0.02) thick X 206mm (+(0.0/-1.00) wide X 1045mm (+0.00/-5.00) long specn. Steel to IS :513-1986 latest issue DD quality semi killed fine finish and best surface.()
Specification : C.R. Bright Annealed steel strip size 1.05mm (+0.02) thick X 206mm (+(0.0/-1.00) wide X 1045mm (+0.00/-5.00) long specn. Steel to IS :513-1986 latest issue DD quality semi killed fine finish and best surface.
Specification : STEEL SQUARE 45MM TO SPEC.BS:970 PT.1 1983 GR.708 M40 (OR) EN-19A FOR TRUNNION-TAR (K-4002) OR STEEL SQUARE 45MM TO SPEC.BS:970 PT.1 1983 GR.709 M40 (OR) EN-19 FOR TRUNNION-TAR (K-4002) OR STEEL SQUARE 45MM TO SPEC.BS:970 PT.1 1983 GR.817
R
Estab
Category : ddp
Grade : 3
Size :
S
1Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) Steel Round 16mm Dia 1983 GD 420 S37 EN 56 C
Description : Steel Round 16mm Dia 1983 GD 420 S37 EN 56 C()
Specification : Steel Round 16mm Dia. 1983 GD. 420 S37. (EN 56 C)
R
Estab
Category : ddp
Grade : 3
Size :
S
1Ordnance Factory Khamaria
Name
Specification
Use
Status
1) BRASS ROD 23 MM BS 2872 CZ 128 LF 0711900023[07]()
Specification : BRASS ROD 23 MM DIA X 2.5 TO 3.0 METRE LONG.TO SPECN| BS|2872-89 GDE-CZ 128.
R
Nonestab
2) BRASS TUBE 13 85X10 95X185L IS 407 LF 0717255200[07]()
Specification : BRASS TUBE SIZE 13.85 +0.1 OD X 10.95 -0.05 ID X 185(-0.3)MMLONG IS-407-1981 (THIRD REV.)(REAFFIRMED 2006) GRD.CU Zn 30AS "TA" COND WITH PROP RM-300/332 MPa HARDNESS 50 TO 62 HRB.
R
Nonestab
3) BRASS ROD 11MM BS2874 CZ122 M LF 0712203011[07]()
Specification : BRASS ROD 11+/- 0.10 MM DIA IN LENGTH OF 2 METRES MIN SPECN BS -2874 -1986, CZ-114 M OR CZ 122M.
R
Nonestab
4) BRASS ROD 17MM SPECN IS 319 89 GR 2 LF 0712100017[07]()
Specification : BRASS ROD SIZE 17.00 MM OD TO SPECN.IS-319-2007 (FIFTH REV.)GR-2 HB- COND WITH PROP.TENSILE STRENGTH -380 MPa MIN.ELONGATION-10% MIN.ON /5.65 SQ.YEILD STRENGTH - 170 MPa MIN.HARDNESS - 60 TO 80 R.C "B" IN LENGTH OF ROD 2.5 TO 3 MTRS.
R
Nonestab
5) CUPRO NI TUBE 46.8X40.3 MM BMK-07G-55 (0744358500)[07]()
Specification : CUPRO NICKEL TUBING WITH HARDNESS 55 TO 65 Hb IN STRAIGHT LENGTH OF 2 TO 3 MTRS.PACKED PROPERLY TO ENSURE STRAIGHTNESSSIZE 46.8+/-0.20 MM O/D x 40.3+/-0.10 MM I/D (PERMISSIBLEVARIATION IN WALL THICKNESS 0.3MM Max) TO BOFORS SPECN:BMK-07-G
Specification : BRASS TUBING 7.11 +/-0.1 MM I/D X 7.93+/-0.076 MM O/D IN RANDUM LENGTH OF 1 MTR. MIN. EXTRUTED AND DRAWN CONDITIONSPECN: BS:2871 PT-2 OF 1972 CZ-126.
R
Nonestab
7) BRASS ROD 11 MM BS 2874 CZ122 H LF 0712200012[07]()
Specification : BRASS ROD 11 +/-0.10 MM DIA IN THE LENGTH OF 2 METER MIN TO SPECN.BS-2874 CZ-122 H
R
Nonestab
8) BRASS ROD 4MM BSEN12166 CUZN35PB2 LF 0717501004[07]()
Specification : BRASS ROD 4 +/-0.05 MM DIA IN ST. LENGTH OF 2 METERS MIN.TO SPECN.BS EN 12166:2011 DESIGN.CuZn35Pb2 MATERIAL CONDITIONR540 WITH UTS=54-65 Kgf/MM2 & ELONGATION=5% MIN
R
Nonestab
9) BRASS ROD 14 MM BS 2874 CZ124 LF 0711900014[07]()
Specification : BRASS ROD 14+/-0.05 MM DIA X 2.5 TO 3.0 METRE LONG.TO SPECN.LEADED BRASS CZ-124 SEPCN.BS-2874 (1969).
R
Nonestab
10) BRASS ROD 4MM BSEN12166 CUZN39PB2 LF 0717501005[07]()
Specification : BRASS ROD 4MM BSEN12166 CUZN39PB2
R
Nonestab
11) BRASS ROD 8 5 MM IS 4170 CU ZN 40 LF 0711906010[07]()
Specification : BRASS ROD 8.5 MM DIA X 2.5 TO 3.0 METRE LONG.TO SPECN| IS|4170,CU ZN 40.
R
Nonestab
12) BRASS ROD 6 35MM IS 319 GRD 1 HB LF 0711904006[07]()
Specification : BRASS ROD 6.35 +0.025-0.075 MM DIA IN LENGTH OF 2 MTR (MIN) & 2.5 MTRS (MAX) TO SPECN. IS-319-2007 (FIFTH REVISION)GRADE-1 CONDITION - HB.
R
Nonestab
13) BRASS ROD 9 5MM OD IS 319 89 GR 2 LF 0712100010[07]()
Specification : BRASS ROD SIZE 9.5MM DIA TO SPECN.IS-319-2007 GR-2 (FIFTH - REVISION) HB.COND WITH PROP.TENSILE STRENGTH-380 Mpa MIN.ALONGATION-10% MIN ON 5.65 /5.65 SQ.YEILD STRENGTH - 170 MPaMIN . HARDNESS- 60 TO 80 R.C "B".
R
Nonestab
14) BRASS ROD 8MM BS2874 CZ122 M LF 0712100008[07]()
Specification : BRASS TUBE 14.20 +0.1 O/DX10.80 MM ID X240 MM LONG.DRAWN BRASS TUBING,TYPE CZ 108 TO SPECN|BS|2871(1972)PART.II-INCLUDING AMDT.1(1976).CONDITION M.
R
Nonestab
16) BRASS ROD 17MM BS2874 CZ121 PB3 LF 0712100933[07]()
Specification : COPPER TUBE O/D 46.8 (+/-)0.20MM X I/D 40.3 (+/-)0.10MM IN STRAIGHT LENGTH OF 1.5 Mtr. TO 3 Mtr. TO SPECN- JSS-4710-01-2007 (REV NO.4)GRADE-I
Specification : COPPER TUBE 35.2044 MM +/-0.1016 MM OUTER DIA X 3.2512 MM +/-0.1524 MM WALL THICKNESS IN LENGTH OF 3.0480 TO 3.6576METER TO SPECIFICATION JSS-4710-01-2007 (REV.NO.4) GRADE-1.
Specification : COPPER TUBE O/D 92.5MM +/- 0.25 MM x I/D 83.7+0.30 MM IN ST.LENGTH OF 300MM TO 400MM TO SPECN.JSS-4710-01-2007(REV.NO.4)GR.1 NOTE: WALL THICKNESS VARIATION SHOULD NOT BE MORE THAN0.3MM WITHIN SAME TUBE. MATERIAL TO BE SUPPLIED IN AS DRAWN
R
Nonestab
20) COPPER TUBE 35X2 5MM W T JSS 4710 1 lf 0707255389[07]()
Specification : COPPER TUBE 35+/-0.5 MM O/D X 2.5+/-0.25 MM WALL THICKNESS IN LENGTH OF 1.5 TO 3 METS. MIN. TO SPECN:-JSS-4710-01:2007(REVISION NO.4) GRADE 1 IN HARD DRAWN CONDITION.
R
Nonestab
21) BRASS ROD 37 5MM BS2874 CZ122M 0712200038[07]()
Specification : BRASS ROD 37.5 [+0.075/-0.13] MM DIA EXTRUDED DRAWN & REALED IN ST. LENGTH OF 2 - 3 METRES TO SPECN: BS-2874-1986 CZ-122 "M" COND. (LEAD CONTENT 1.0 TO 1.75%, ANTIMONY 0.02% MAX.
R
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Khamaria
[ENR Registration]
Name
Specification
Use
Status
1) Steel strip cold rolled closed annealed bright finished 3 56mm thick X 80mm wide in length of 2 mtrs LF0122223036
Description : Steel strip cold rolled closed annealed bright finished 3 56mm thick X 80mm wide in length of 2 mtrs LF0122223036()
Specification : Steel strip cold rolled closed annealed bright finished 3.56(+0.10/-0.00) mm thick X 80 +/-0.25mm wide in length of 2 mtrs to specn:- IS-513:2008 (Fifth Revision) Grade "DD" Temper 5(Annealed)
R
Nonestab
Category : s
Grade : 3
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) STEEL ROD 32MM DIA[04]()
Specification : STEEL ROD 32.00MM DIA-0.1MM HOT ROLLED PEELED BAR IN EXACT LENGTH OF 760MM +2MM EACH PIECE TO SPECN.BS 970 PT:1:1983. GD 835 M15 WITH RESTRICTION OF S%=0.01 MAX,P%=0.015MA X,(S+P)%=0.022MAX,VACUAM DEGASED & DEVOID OF UNDESIRABLE ELEMENT A
R
Nonestab
2) STEEL FLAT 125X 8X 530 MM LONG IN CUT LENGTH[01]()
Specification : ST.FLAT 125 X 8 X 530 MM LONG IN CUT LENGTH IN H.R & NORM. CONDN. TO SPECN.IS:5517-1993 DESIGNATION 55C8 TEST PIECE TO BE TESTED AS PER SPECN.TOLLERANCE ON WIDTH +/-2MM,ON THICKNE
SS +/-0.25MM.
R
Nonestab
3) STEEL ROD 4 MM DIA[03]()
Specification : STEEL ROD 4.0MM DIA TO SPECN STEEL BS 970 PT 1:1983 GRADE 835M30.
R
Nonestab
4) DIA 6MM SS WIRE ROD IS6528 1972 GR 04 CR 18 NI 10 FULLY SOFTENED FOR FIRING DEVICE[01]()
Specification : DIA 6MM SS WIRE ROD IS6528-1972 GR 04 CR 18 NI 10 FULLY SOFTENED
R
Nonestab
5) SQUARE DRAWN 1 upon 4 Inch ROD FOR FIRING DEVICE[01]()
Specification : SQUARE DRAWN ROD OF 1/4" (6.35MM) BRASS, BS, 2874:1969 CZ 122 H
R
Nonestab
6) STEEL STRIP FOR FIRING DEVICE[01]()
Specification : STEEL STRIP TO SPECN : BS:1449:PT:1:1983 HR 15 STEEL SIZE 3.25MM X 70MM X 1250MM FOR BAR TO DRG.NO IUX-615 FOR CI (A) KIRKEE, (IFD)
R
Nonestab
7) SS WIRE ROD DIA 10MM[01]()
Specification : SS WIRE ROD DIA 10MM SPEC. IS 6527-1978 GR 04 CR 18 NI 10
R
Nonestab
8) Steel Round Dia 28mm[14]()
Specification : STEEL ROUND DIA 28MM SPEC. BS 970 PT-1: 1983-GR-070 M 20
R
Nonestab
9) STEEL SHEET POINT 9MM 20SWG X 1000 X 1500MM FOR STIRKER MECHANISM[01]()
Specification : STEEL SHEET 0.9MM (20SWG) X 1000 X 1500MM, STEEL IS:1570 (PART-2/SEC-1): 1979 10C4 OR BS:1449 PART-3A) : 1964 GD HS-12 FOR STRIKER AS PER DRG NO. NAD 7606/2.
R
Nonestab
10) STEEL SHEET POINT 9MM 20SWG X1000X1500MM MATL FOR STIKER MECHANISM[01]()
Specification : STEEL SHEET 0.9MM (20SWG) X1000X1500MM.MATL. SPECTV.STA,5V2, V2A,V2B,OR IS:1570 (PART-2/SEC-1)- 1979, 15C4 OR BS:1449 (PART 3A):1964.GD HS-12 FOR FLY OFF LEVER AS PER DRG.NO.NAD 7606/4.
R
Nonestab
11) BRASS TUBE FOR STRIKER MECHANISM[07]()
Specification : BRASS TUBE 5.7(-0.1)MM O/D WALL THICKNESS 0.7MM (22SWG)X 4000MM STA 7 CZ 4 OR CZ 5 OR IS:2501-1963 OR BS:2871-1957,CZ 105, 378-1963, 855- 1963 OR 267-1963 FOR SLEEVE AS PER DRG NO. NAD 7606/7.
R
Nonestab
12) SPRING STEEL WIRE DIA 1 POINT 1 MM FOR STRIKER MECHANISM[01]()
Specification : SPRING STEEL WIRE DIA 1.1MM MATERIAL SPECIV.STA 3 OR 4 OR IS: 4454:2001,SL OR BS:1408:1964, 1408-C FOR SPRING AS PER DRG.ANO.NAD 7606/5
R
Nonestab
13) STEEL ROD DIA 4 MM X4000MM FOR STRIKER MECHANISM[01]()
Specification : STEEL ROD DIA 4.0MM X4000MM AS PER SPECI.STA 5 VIB OR V3 OR IS: 1570 PART 22/SEC-1) :1961 14CI4SI4 OR 20C8 OR BS:970- 1955, EN 7A OR BS:970 (PART-1): 983,070M20 FOR PIN HINGE AS PER DRG.NO. NAD 7606/3.
R
Nonestab
14) STEEL FLAT RECTANGULAR SIZE 40 plus 5 MM X 65 plus 5 MM for TAR[01]()
Specification : STEEL FLAT RECTANGULAR SIZE (40+5)MMX(65+5)MM IN THE LENGTH OF 1.5 TO 3MTR TO SPECN. BS:970 PT1 1983,GR 817 M40 HOT ROLLED AND NORMALISED CONDITION.TEST PIECE HARDNESS TO ACHIEVE 425-475 HV.
R
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Khamaria
[ENR Registration]
Name
Specification
Use
Status
1) STEEL ROD 18MM BS970 080M50 CD ANL Lf 0133001165
Description : STEEL ROD 18MM BS970 080M50 CD ANL Lf 0133001165()
Specification : STEEL ROD 18+0.05/-0.10 MM DIA TO SPECN:BS-970-PT-I/1983 GR-080M-50 COLD DRAWN & SOFTENED COND.IN ST.LENGTH OF 2.5 TO 3MTRS HARDNESS 207HB(max) MATERIAL TO BE SUPPLIED WITH COLOURCODE,BASE COLOUR-BLACK,1st-BAND WHITE TO SPECN:IS-2049-78(R
Specification : MILD STEEL STRIP 100+/-1 MM WIDE x 26 BG (0.50MM) THICK IN ROLLS COLD DRAWN ANNEALED BEST SURFACE TYPE D MATT FINISHTO SPECN:-IS-513-2008 (FIFTH REVISION) WEIGHT OF EACH ROLLSHOULD BE BETWEEN 50 KG TO 100 KG.
Specification : STEEL STRIP 200+/-0.5 MM WIDE X 1.1+/-0.05 MM THICK TO SPECN IS-513-TYPE DD OR BS-1449 PT-I GR-3,CS OR CR
R
Nonestab
Category : s
Grade : 3
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) STEEL ALLOY BAR SAE 4130 PER SAE AMS S 6758 OR SAE 4340 PER SAE AMS S 5000 ROD DIA 90X154L IN MM ALL RELEVANT TEST CERTIFICATE FROM NABL LAB TO BE SUBMITTED for SRCG[02]()
Specification : STEEL ALLOY BAR SAE 4130 PER SAE-AMS-S-6758 OR SAE 4340 PER SAE-AMS-S-5000. ROD DIA 90X154L IN MM ALL RELEVANT TEST CERTIFICATE FROM NABL LAB TO BE SUBMITTED. for SRCG
R
Nonestab
2) CRES PLATE 316 PER ASTM A 240 SIZE20TX25WX90L IN MM ALL RELEVANT TEST CERTIFICATE FROM NABL ACCREDITED LAB TO BE SUBMITTED[03]()
Specification : CRES PLATE 316 PER ASTM-A-240. SIZE:20TX25WX90L (IN MM). ALL RELEVANT TEST CERTIFICATE FROM NABL ACCREDITED LAB TO BE SUBMITTED.
R
Nonestab
3) ALLOY STEEL PLATE THICK 16 MM SAE 4130 PER SAE AMS 6345 PLATE SIZE 16T X 90L X80W IN MM ALL RELEVANT TEST CERTIFICATE FROM NABL LAB TO BE SUBMITTED FOR SRCG[02]()
Specification : FOR ALLOYSTEELPLATETHICK16MMSAE4130PERSAE-AMS-6345. PLATE SIZE: 16T X 90L X80W (IN MM). ALLRELEVANTTESTCERTIFICATEFROMNABLLABTO BE SUBMITTED.FORSRCG
R
Nonestab
4) CRES ROD 304L PER ASTM A 276 ROD DIA 14MM ALL RELEVANT TEST CERTIFICATE FROM NABL LAB TO BE SUBMITTED[03]()
Specification : CRES ROD 304L PER ASTM-A-276. ROD DIA 14MM. ALL RELEVANT TEST CERTIFICATE FROM NABL LAB TO BE SUBMITTED.
Specification : Steel Sq. 25mm to Specn. BS:970 Part-1:1991 GRD.835 M15 in forged & annealed Condition
R
Estab
Category : ddp
Grade : 3
Size :
S
1Ordnance Factory Khamaria
[ENR Registration]
Name
Specification
Use
Status
1) STEEL STRIP 12 5 X 0 28 MM IS 6911 1992 LF 0323060012
Description : STEEL STRIP 12 5 X 0 28 MM IS 6911 1992 LF 0323060012()
Specification : STEEL STRIP 12.5 +/- 0.5MM WIDE X 0.28-0.02MM THICK IN FORM OF COILS OF CONTINUOUS LENGTH TO SPECIFICATION IS-6911-2017 (2nd REVISION) AMENDMENT NO. 1 & 2 , Gr X04 Cr 19 Ni 9. EACH COIL WEIGHT 5-10 KG
R
Nonestab
2) STEEL STRIP 90X2MM IS 513 BS1449 LF 0101061544
Description : STEEL STRIP 90X2MM IS 513 BS1449 LF 0101061544()
Specification : STEEL STRIP 90+/-0.5mm WIDE X 2mm THICK TO SPECN-IS-513-2008(FIFTH REV.)GRD. DD OR EDD IN ANNEALED/SKIN PASSED CONDITIONOR BS-1449 Pt-I GR. 1 OR 2 OR 3 (CR/CS) IN ANNEALED/SKINPASSED COND. ALTERNATIVE GR.1 OR 2 OR 3 OF BS-1449-Pt-I IN(HR/
R
Nonestab
Category : s
Grade : 3
Size :
S
1Ordnance Factory Khamaria
[ENR Registration]
Name
Specification
Use
Status
1) STEEL ROD 18 MM JSS 9510 01 SS D32 LF 0135300018
Description : STEEL ROD 18 MM JSS 9510 01 SS D32 LF 0135300018()
Specification : STEEL ROD 18+0.05/-0.10MM DIA,TO SPECN.SS/D32 TO JSS-9510-01IN NORMALISED CONDITION OR BS-970-PT-1-1983 GRADE O8OM5O INNORMALISED CONDITION,IN ST.LENGTH OF3+/-0.1MTR,HARDNESS 187HB TO 207 HB.MATERIAL TO BE SUPPLIED WITH COLOUR CODE BASECO
R
Nonestab
Category : s
Grade : 3
Size :
S
1Gun and Shell Factory
[ENR Registration]
Name
Specification
Use
Status
1) BRASS RODS 38point1 plus minus 0point1mm DIA TO SPEC BS 2874 1986 CZ 122 PB 3 IN M CONDITION
Description : BRASS RODS 38point1 plus minus 0point1mm DIA TO SPEC BS 2874 1986 CZ 122 PB 3 IN M CONDITION()
Specification : BRASS RODS 38.1+/- 0.1mm DIA BS 2874:1986 -CZ 122 PB-3 IN "M" CONDITION.
R
Estab
Category : p
Grade : 3
Size :
S
1Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) STEEL FLAT SIZE 6 X 22 MM IN HOT ROLLED AND NORMALISED CONDN FOR MAG
Description : STEEL FLAT SIZE 6 X 22 MM IN HOT ROLLED AND NORMALISED CONDN FOR MAG()
Specification : STEEL FLAT SIZE:- 6 X 22MM IN HOT ROLLED & NORMALISED CONDN.TO SPECIFICATION BS:970:PT.3:1991:GR.070M55 MATERIAL TO BE TESTED IN HARDENED & TEMPERED CONDITION AS PER RULING SECTION & SEPERATE TEST PIECE NEED TO BE HEAT TREATED TO ACHIEVE
Specification : STEEL STRIP 85+/- 0.5 MM WIDE X 2 MM THICK TO SPECN:-IS-513 GRADE DD OR EDD IN ANNEALED/SKIN PASSED CONDITION OR BS-1449-Pt-I GR.1 OR 2 OR 3 (CR/CS) IN ANNEALED & SKIN PASSED COND. ALTERNATIVE GR.1 OR 2 OR 3 OF BS-1449-Pt-I IN (HR/HS) CON
Specification : STC RD 1"(25MM) DIA TEMP-B WITH THE FOLLOWING CHEMICAL COMPOSITION:-C%=1.15 TO 1.25 SI%=0.25 MAX., MN%-0.45 MAX., S&P%=0.035 MAX. OR AS PER IS-3749-1978 GRADE T-118
R
Estab
Category : ddp
Grade : 3
Size :
S
1Gun Carriage Factory
Name
Specification
Use
Status
1) 0720300095 PB ROUND 95MM DIA STD LENGTH TOM SPECIFICATION IS 7811 1985[70]()
Specification : 0720300095 P.B.ROUND 95MM DIA STD.LENGTH TOM SPECN: IS: 7811-1985.
R
Nonestab
2) 0720201038 PB ROUND 38 MM DIA IN STD LENGTH TO SPECN IS 7811 1985[70]()
Specification : 0720201038 PB.ROUND 38.00 MM DIA IN STD.LENGTH TO SPECN.IS:7811-1985
R
Nonestab
3) 0720201100 PB ROUND 100MM DIA TO SPECIFICATION IS 28 1985 GRII CONTINOUS CAST IN LENGTH OF 1 METRES OR ITS MULTIPLE LENGTH[70]()
Specification : 0720201100 P.B.ROUND 100MM DIA.TO SPECN.IS:28-1985-GRII(CONTINOUS-CAST) IN LENGTH OF 1.00 METRES OR ITS MULTIPLE LENGTH
R
Nonestab
4) P B ROUND EXTRUDED 140 MM DIA x 1200 MM LONG OR ITS MULTIPLE TO SPECN BS 2874 86 DESIGNATION PB 102 OR IS1385 PCU Sn6[70]()
Specification : P.B.ROUND EXTRUDED 140 MM DIA X 1200 MM LONG OR ITS MULTIPLE TO SPECN.BS:2874-86,DESIGNATION PB-102.OR IS:1385,PCU Sn6.
R
Nonestab
5) P B Rod 127 MM Dai x 1 Mtr Long Or its Multiple to Spec BS 2874 1986 Designation PB 102[70]()
Specification : P B Rod 127 MM Dai x 1 Mtr Long Or its Multiple to Spec BS 2874 1986 Designation PB 102
R
Nonestab
6) 0725577121 PB HOLLOW BAR 135MM OD X 95MM ID IS 28 1985 GRADE 2 CONTINUOUS CAST[70]()
Specification : 0725577121 PB HOLLOW BAR 135MM O/D X 95MM I/D IS:28-1985 GRADE 2 CONTINUOUS CAST
R
Nonestab
7) PHOSPHOR BRONZE ROD 127MM DIA X 1 MTR LONG OR ITS MULTIPLE TO SPECN BS 2874 1986 DESIGNATION PB 102[70]()
Specification : PHOSPHOR BRONZE ROD 127MM DIA X 1 MTR LONG OR ITS MULTIPLE TO SPECN: BS:2874-1986, DESIGNATION PB-102
R
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Khamaria
[ENR Registration]
Name
Specification
Use
Status
1) Brass rod 8 5mm bs 2874 cz129 m LF 0741100004
Description : Brass rod 8 5mm bs 2874 cz129 m LF 0741100004()
Specification : Brass rod 8 5mm(-0.050)mm Dia in straight length of 3.0meter(-0.2m max) to specn:BS-2874-CZ-129 cond. 'M' circular ovality 0.020mm max; straightness 01mm in 01 meter & rod should be packed in a suitable box to prevent bending during trans
Specification : STEEL ROD 32 [+0.00/-0.10] mm DIA STEEL 53 x m10 TO SPECN: TY-14-1-2232-77. IN STRAIGHT LENGTH OF 2 TO 2.5 MTRS WITH CHEMICAL & PHYSICAL PROPERTIES AS PER STEEL SPEC.NO.ML:003SHT 1 OF 1 DATE 17/11/95. EACH ROD SHOULD HAVE ONE END MACHINED
R
Nonestab
2) STEEL ROD 21MM IS4431 GR 14 C14 S14 LF 0111000021[01]()
Specification : STEEL ROD 21(+0.05/-0.10) MM DIA TO SPECN:- IS-4431-1978 (REAFFIRMED 2014)(FIRST REV.) GR-14 C-14,S-14 IN CD FINISHIN STRAIGHT LENGTH OF 2 TO 2.5 MTRS.
R
Nonestab
3) STEEL ROD 41MM JSS:9510-01 SS/C24-A (0113000041)[01]()
Specification : STEEL FREE CUTTING BRIGHT TURNED, REELED GROUND BAR 41(+0.00/-0.10)MM DIA IN LENGTH OF 2.5TO 3MTR.SPECN-JSS-9510-01-2013(REV.NO.3)DESIG SS/C24-A.MATERIAL SHOULD BE FREE FROM CRACKSFLAWS ROLLING LAPS ETC & SHOULD BE SUBJECTED TO 100% CRACK
R
Nonestab
4) BRASS ROD 21MM BS2874 CZ122 M LF 0712202021[07]()
Specification : BRASS ROD 21+/-0.15 MM DIA EXTRUDED DRAWN & REELED IN ST. LENGTH OF 2 MTRS. MINIMUM TO SPECN:-BS-2874-1986, CZ-122CONDITION "M".
Specification : BRASS STRIP 20+/-0.5MM WIDE X0.71+/-0.02MM THICK TO SPECN: IS-410-1977,GR.CuZn37 COND"O" IN COIL OF 8 METER LENGTHMINIMUM.
R
Nonestab
6) BRASS ROD 14MM BS2874 CZ122 M LF 0717703904[07]()
Specification : BRASS ROD 14+/- 0.10 MM DIA IN ST LENGTH OF 1.5 TO 2 METRES MIN SPECN.BS 2874-1986 CZ-122 "M"
R
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Khamaria
Name
Specification
Use
Status
1) STEEL ROD 14 5MM IS 4431 14C14S14CD LF 0133001145[01]()
Specification : STEEL ROD 14.5(+0.05/-0.10]MM DIA IN ST.LENGTH OF 2TO 2.5MTRTO SPECN:IS-4431-1978(REAFFIRMED 2014)(1st REVESION)GRADE-14C14S14 IN COLD DRAWN COND.MATERIAL COLOUR CODE:BASE COLOUR-BROWN,Ist BAND-WHITE,COLOUR TO SPECN.IS-2049-78(REAFFIRMED
R
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) ALLOY STEEL FERROUS & NON-FERRIOUS OD DIFFERENT STANDARDS[10]()
Specification : AS PER SPECIFICATION
R
Estab
Category : S
Grade : III
Size :
1Small Arms Factory
Name
Specification
Use
Status
1) ALLOY STEEL FERROUS & NON-FERRIOUS OD DIFFERENT STANDARDS[01]()
Specification : AS PER SPECIFICATION
R
Nonestab
2) Sheet for JVPC[01]()
Specification : 1.0 mm thickness IS: 513-1994, GD EDD for plate form magazine
R
Nonestab
3) St Rd 3 point 25mm dia for JVPC[01]()
Specification : St. Rod 3.25MM dia to Specn. IS:5517-1993.40CB(EN-8) (Pin St. Hdls. Cocking Bracket & Gas block)
R
Nonestab
4) St Rd 4 point 47 MM dia for JVPC[01]()
Specification : St. Rd. 4.47MM dia to Specn. IS:5517-1993.GD-55CB(EN-9)(5 types of Pin)
R
Nonestab
5) St Rod 6 point 35 mm dia for JVPC[01]()
Specification : St. Rod 6.35 mm dia to Specn. IS: 3748-1990 T90MN6WCR2 (Rod Cocking)
R
Nonestab
6) St Rod 8 point 23 mm dia for JVPC[01]()
Specification : St. Rod 8.23mm dia for JVPC
R
Nonestab
7) Steel flat 36mm x 62mm for JVPC[01]()
Specification : BS:970 Pt.I 1983 GD 835 M 15 OR EN-39-B
R
Nonestab
8) STEEL ROD[01]()
Specification : STEEL ROD 31+0.5/-0.0MM DIA.,IN CUT LENGTH OF 380+2.5/-0.0MM TO SPECN. JSS:9510-06-2000,REV.3 CODE REF.B IN NORMALISED CONDITION. COMPOSITION RESTRICTED: S%=0.010MAX.,P%=0.015MAX.&
(S+P)%=0.022MAX. FOR RIFLE 5.56MM. FOR OTHER PARAMETERS
R
Nonestab
9) STEEL ROD 32MM DIA[01]()
Specification : STEEL ROD 32.00MM DIA-0.1MM HOT ROLLED PEELED BAR IN EXACT LENGTH OF 760MM +2MM EACH PIECE TO SPECN.BS 970 PT:1:1983. GD 835 M15 WITH RESTRICTION OF S%=0.01 MAX,P%=0.015MAX,(S+P)%=0.022MAX,VACUAM DEGASED & DEVOID OF UNDESIRABLE E
R
Estab
10) STEEL ROD DIA 8MM STEEL TO IS:5517-1993,GD-42CR4M02 0R EN-19[01]()
Specification : STEEL ROD DIA 8MM STEEL TO IS:5517-1993,GD-42CR4M02 0R EN-19
R
Nonestab
11) STEEL ROUND dia for JVPC[01]()
Specification : SPECN:IS:5517-1993 grade 40 NI 6CR4 Mo3(EN-24)
R
Nonestab
12) Steel wire Spring for JVPC[01]()
Specification : Steel wire Spring for JVPC steel to IS:4454(Part-I) 2001 DH
R
Nonestab
13) DIA 6MM SS WIRE ROD IS6528 1972 GR 04 CR 18 NI 10 FULLY SOFTENED FOR FIRING DEVICE[01]()
Specification : DIA 6MM SS WIRE ROD IS6528-1972 GR 04 CR 18 NI 10 FULLY SOFTENED
R
Nonestab
14) RAW MATERIAL OF BARREL ST. ROD 40.0 MM DIA TO SPEC. JSS:9510 -06-2012 CODE REF .B. T - I COND.[01]()
Specification : SPEC. JSS:9510 -06-2012 CODE REF .B. T - I COND.
R
Nonestab
15) SPG STEEL WIRE 1.216 MM (18SWG)[01]()
Specification : SPRING STEEL WIRE 18 SWG (0.048") DIA TO SPECIFICATION BS:5216-1991 GD ND-3 REQUIRED FOR SPRING MAIN OF 9MM CARBINE
R
Nonestab
16) SPRING STEEL WIRE FOR CARBINE 5 56[01]()
Specification : SPRING STEEL WIRE DIA. 1.30MM TO SPECN- IS:4454:PT-1:2001GD-DH WITH UTS VALUE MIN 2300N/MM2
R
Nonestab
17) SS WIRE ROD DIA 10MM[01]()
Specification : SS WIRE ROD DIA 10MM SPEC. IS 6527-1978 GR 04 CR 18 NI 10
R
Estab
18) ST FLAT SIZE 22 X 60MM[01]()
Specification : ST FLAT SIZE 22 X 60MM IN HOT ROLLED & ANNEALED CONDITIONTO SPECIFICATION BS:970:PT 1:1983 : GD 708M40,
R
Estab
19) ST RD 22MM DIA IN HOT ROLLED AND ANNEALED CONDITION[03]()
Specification : ST.RD.22MM DIA IN HOT ROLLED & ANNEALED CONDITION TO SPECN IS:6527:1995,DESIGNATION X30CR 13 (FOR PLUG GAS).
R
Estab
20) ST ROUND 8 MM DIA[03]()
Specification : ST ROUND 8.00 MM DIA. TO SPECN. BS-970 PT.IIOF 1970 GD. 708 M40 (REQD.FOR-PIN FIRING OF 9MM CARBINE) ACCEPTANCE STANDARDS:MACRO ETCH TEST AS PER ASTME381 & NMIR TEST AS PER IS:4163-82
R
Estab
21) ST SHEET 1.00X1250X2500MM DD QUALITY. (COLD ROLLED ) TO SPECIFICATION IS:513-(LATEST ISSUE).[01]()
Specification : ST.STRIP SIZE:- 1.8MM THICK X270MM WIDE X1600MM LONG TO SPECN. IS:7226-1974 GRADE C-40, COLD ROLLED & ANNEALED CONDN. NOTE:- GRAIN DIRECTION SHOULD BE ALONG THE LENGTH.
R
Nonestab
23) ST STRIP MM FOR REVOLVER[01]()
Specification : ST. STRIP 1.8 MM THICK X 72 MM X 1050 MM LENGTH WITH GRAINS IN LENGTH-WISE DIRECTION TO SPECN. STEEL IS:7226-1974,DESIGNATION C 40 (FOR BRACKET FRONT).
R
Estab
24) ST STRIP FOR LMG[01]()
Specification : ST. STRIP 1.8 MM THICK X 72 MM X 1050 MM LENGTH WITH GRAINS IN LENGTH-WISE DIRECTION TO SPECN. STEEL IS:7226-1974,DESIGNATION C 40 (FOR BRACKET FRONT).
R
Nonestab
25) ST.RD.25 MM DIA IN HOT ROLLED & ANNEALED/NORMLISED CONDTION TO SPECIFICATION BS:970.PT.1 1983 GD.605M36[01]()
27) STEEL FLAT 17X47MM IN HOT ROLLED AND ANNEALED AT 650 C[01]()
Specification : SPECN.BS:970:PT-3:1991 GD.945M38 T.P.TESTED IN `T'CONDITION MACRO ETCH TEST & NMIR TEST AS PER ANNEXURE-A NATURE-C.(REQD.FOR-SHOULDER LOCKING LEFT & RIGHT DS CAT 1005-007907)
C
Nonestab
28) STEEL FLAT 22X18MM FOR MAG[03]()
Specification : SPECN. IS: 5517:1993 DESIGNATION 40 NI 6 CR 4 MO2 (REQD.FOR LINK PISTON EXTN.OF MAG 7.62MM)
R
Estab
29) STEEL FLAT 25X32MM[03]()
Specification : STEEL FLAT 25X32MM(1"X1-1/4")TO SPECN.BS:970:PT-1:1983 GD.080M40 IN HOT ROLLED & NORMALISED CONDITION. MATL TO BE TESTED AS PER ANNEXURE-C (REQD.FOR BAND FRONT SIGHT OF MAG 7.62MM)
R
Nonestab
30) STEEL FLAT 32X11MM FOR MAG[03]()
Specification : STEEL FLAT 32X11MM TO SPECN: BS:970: PT-3 1991:GD.835M15 IN HOT ROLLED AND ANNEALED CONDITION REQD. FOR GUIDE FRONT LEFT
R
Estab
31) STEEL FLAT 70 X 34 MM IN HOT ROLLED and ANNEALED CONDITION[03]()
Specification : SPECN.BS:970:PT-3:1991.GD.410S21 OR 420S29.TEST PIECE TO BE TESTEDAS PER RULINF SECTION. MATL.SHOULD SATISFY MACRO-ETCH TEST &MICROSCOPIC NON-METALIC INCLUSION RATING AS PER NATURE-C A SEPARATE T.P.TO BE HARDNED TO ACHIEVE HARDNESS 265
33) STEEL RD 12MM DIA IN ANNEALED AND COLD DRAWN CONDITION TO SPECN.BS:970.PT-I:1983 GD.817M40 OR 826M40 (REQD.FOR EXTRACTOR PLUNGER OF MAG 7.62MM)[01]()
Specification : SPECN.BS:970.PT-I:1983 GD.817M40 OR 826M40
R
Estab
34) STEEL RD 13MM DIA IN ANNEALED AND COLD DRAWN CONDITION[03]()
Specification : STEEL RD 13MM DIA IN ANNEALED AND COLD DRAWN CONDITION TO SPECN.BS:970:PT.1:SEC-2-1983 GD 080M40 TEST PIECE TO BE TESTED AS PER SPECIFIC.MATERIAL SHOULD ALSO SATISFY THE TEST AS LAID DOWN IN THE ANNEXURE.
R
Nonestab
35) STEEL RD 22MM DIA IN HOT ROLLED AND ANNEALED CONDITION TO SPECN.BS:970 PT.1:1983 GD.817M40 OR 826M40.[01]()
Specification : SPECN.BS:970 PT.1:1983 GD.817M40 OR 826M40.
R
Estab
36) STEEL RD 25MM DIA FOR MAG[01]()
Specification : SPECN.BS:970:PT-3:1991 GD.420S29 OR 431S29HARDENED & TEMPERED BARS TO HARDNESS 265-300 BHN.MACRO ETCH & NMIR TEST TO BE CARRIED OUT AS PER ANNEXURE NATURE `C'. (REQUIRED FOR GAS REGULATOR D S CAT NO. 1005-006614)
R
Estab
37) STEEL RD 32MM DIA IN HOT ROLLED AND NORMALISED CONDITION TO SPECN.IS-1875-2005 DESIGNATION C8 CLASS 2 LATEST ISSUE[03]()
Specification : SPECN.IS-1875-2005 DESIGNATION C8 CLASS 2 LATEST ISSUE
R
Estab
38) STEEL RD 38MM DIA IN HOT ROLLED AND NORMALISED CONDITION TO SPECN. IS:5517 -1993, DESIGNATION 40 C8[03]()
39) STEEL RD 45MM DIA IN HOT ROLLED AND ANNELED CONDITION FOR MAG[01]()
Specification : SPECNIS:5517-1993 DESIG.42CR4MO2.TEST PIECE TO BE TESTED IN`V' CONDITION.MATL. SHOULD ALSO SATISFY MACRO ETCH & NMIR TEST AS ANNEXURE NATURE-C A SEPERATE T.P. IS TO BE QUENCHED & TEMPERED BEFORE MACHINING TO ACHIEVE HARDNESS 280-335HB.
R
Nonestab
40) STEEL RD 8MM DIA FOR MAG[01]()
Specification : BS 970 PT 1:1983 GR 431 S-29 OR 20 S-37 EN 56C
R
Estab
41) STEEL ROD 14 MM DIA IN HOT ROLLED NORMALIZED CONDITION[03]()
Specification : SPECN.BS:970 PT-3:1991.GD 817M40 OR 826M40 TEST PIECE TO BE TESTED IN `Z' CONDITION.
R
Estab
42) STEEL ROD 30MM DIA. TO SPECN.BS:970:PT.1:1983 GD.070M55 CONDN.'S' (REQD. FOR FLASH HIDER )[03]()
Specification : STEEL RD. 35MM DIA +/- 0.25MM IN HOT ROLLED REELED,PEELED & ANNEALED CONDITION TO SPECN JSS:9510:06:2000(REV. NO.3)CODE REF.'B'.TEST PIECE TO BE TESTED IN 'T' CONDITION.MATERIAL SHOULD ALSO SATISY THE TEST AS PER ANNEXURE 'A' NATURE A A
Specification : STEELROD 44+0.0/-0.50MM DIA.IN CUTLENGTHOF415+2.5/-00MM TO SP ECN.JSS:9510-06-2000,REV.NO.3 CODE REF.BIN T3 CONDITION WITH COMPOSITION RESTRICTED S%-0.010 MAX.P%-0.015 MAX.& (S+P)%-0. 022 MAX.FOR MAG 7.62MM.BARREL FOR OTHER PARAMETERS AS
R
Nonestab
46) STEEL ROUND 12MM DIA[03]()
Specification : STEEL ROUND 12MM.DIA TO SPECN.BS:970.PT:1.1983.GD 835-M-15 OR GD-655 M-13.(EN-39B OR 36B) REQUIRED FOR EXTRACTOR SMALL ARMS CARTRIDGE TO DRG NO.ARDE/SK-2689/250.
Specification : STEEL ROUND 20MM DIA TO SPECN.BS:970:PT.1:1983 GD.080M40 IN HOT ROLLED &NORMALISED CONDITION. TEST PIECE TO BE TESTED AS PER THE SPECIFICATION.
R
Estab
49) STEEL ROUND 27 MM[03]()
Specification : STEEL ROUND 27 MM TO SPECN.IS:5517-1993 DEGIGNATION 55C8 IN ANNEALED & COLD DRAWN CONDN. (FOR SLEEVE LOCKING BIPOD).
R
Nonestab
50) STEEL SQR 37MM FOR MAG[03]()
Specification : SPECN.BS:970:PT-1:1983 GD.945M38 IN HOT ROLLED & NORMALISED CONDITION TEST PIECE TO BE TESTED IN `T' CONDTION
Specification : STEEL STRIP TO SPECN : BS:1449:PT:1:1983 HR 15 STEEL SIZE 3.25MM X 70MM X 1250MM FOR BAR TO DRG.NO IUX-615 FOR CI (A) KIRKEE, (IFD)
R
Nonestab
Category : DDP,DP
Grade : II
Size :
1Small Arms Factory
Name
Specification
Use
Status
1) ALLOY STEEL FERROUS & NON-FERRIOUS OD DIFFERENT STANDARDS[01]()
Specification : AS PER SPECIFICATION
R
Estab
2) Sheet for JVPC[01]()
Specification : 1.0 mm thickness IS: 513-1994, GD EDD for plate form magazine
R
Nonestab
3) St Rd 3 point 25mm dia for JVPC[01]()
Specification : St. Rod 3.25MM dia to Specn. IS:5517-1993.40CB(EN-8) (Pin St. Hdls. Cocking Bracket & Gas block)
R
Nonestab
4) St Rd 4 point 47 MM dia for JVPC[01]()
Specification : St. Rd. 4.47MM dia to Specn. IS:5517-1993.GD-55CB(EN-9)(5 types of Pin)
R
Nonestab
5) St Rod 6 point 35 mm dia for JVPC[01]()
Specification : St. Rod 6.35 mm dia to Specn. IS: 3748-1990 T90MN6WCR2 (Rod Cocking)
R
Nonestab
6) St Rod 8 point 23 mm dia for JVPC[01]()
Specification : St. Rod 8.23mm dia for JVPC
R
Nonestab
7) Steel flat 36mm x 62mm for JVPC[01]()
Specification : BS:970 Pt.I 1983 GD 835 M 15 OR EN-39-B
R
Nonestab
8) STEEL ROD 31+0.5/-0.0MM DIA.,IN CUT LENGTH OF 380+2.5/-0.0MM TO SPECN. JSS:9510-06-2000,REV.3[01]()
Specification : STEEL ROD 31+0.5/-0.0MM DIA.,IN CUT LENGTH OF 380+2.5/-0.0MM TO SPECN. JSS:9510-06-2000,REV.3 CODE REF.B IN NORMALISED CONDITION. COMPOSITION RESTRICTED: S%=0.010MAX.,P%=0.015MAX.&
(S+P)%=0.022MAX. FOR RIFLE 5.56MM. FOR OTHER PARAMETERS A
R
Nonestab
9) STEEL ROD 32MM DIA[01]()
Specification : STEEL ROD 32.00MM DIA-0.1MM HOT ROLLED PEELED BAR IN EXACT LENGTH OF 760MM +2MM EACH PIECE TO SPECN.BS 970 PT:1:1983. GD 835 M15 WITH RESTRICTION OF S%=0.01 MAX,P%=0.015MAX,(S+P)%=0.022MAX,VACUAM DEGASED & DEVOID OF UNDESIRABLE EL
R
Nonestab
10) STEEL ROD DIA 8MM STEEL TO IS:5517-1993,GD-42CR4M02 0R EN-19[01]()
Specification : STEEL ROD DIA 8MM STEEL TO IS:5517-1993,GD-42CR4M02 0R EN-19
R
Nonestab
11) STEEL ROUND dia for JVPC[01]()
Specification : SPECN:IS:5517-1993 grade 40 NI 6CR4 Mo3(EN-24)
R
Nonestab
12) Steel wire Spring for JVPC[01]()
Specification : Steel wire Spring for JVPC steel to IS:4454(Part-I) 2001 DH
R
Nonestab
Category : DDP,DP
Grade : II
Size :
1Gun and Shell Factory
[Deemed Registration]
Name
Specification
Use
Status
1) BRASS ROUND 38 POINT 1 PLUS 0POINT25 MM DIA TO SPECN BS 2874 CZ 121 PB3 M IN THE LENGTH OF2 MTRS MINIMUM LONG BAR LATEST ISSUE
Description : BRASS ROUND 38 POINT 1 PLUS 0POINT25 MM DIA TO SPECN BS 2874 CZ 121 PB3 M IN THE LENGTH OF2 MTRS MINIMUM LONG BAR LATEST ISSUE()
Specification : BRASS ROUND 38.1 +0.25mm DIA TO SPECN BS-2874-CZ-121 PB3-"M" IN THE LENGTH OF2 MTRS (MINIMUM) LONG BAR. LATEST ISSUE
R
Estab
Category : p
Grade : 3
Size :
S
1Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) SPRING STEEL WIRE FOR CARBINE 5 56
Description : SPRING STEEL WIRE FOR CARBINE 5 56()
Specification : SPRING STEEL WIRE DIA. 1.30MM TO SPECN- IS:4454:PT-1:2001GD-DH WITH UTS VALUE MIN 2300N/MM2
R
Estab
2) ST.RD.25 MM DIA IN HOT ROLLED & ANNEALED/NORMLISED CONDTION TO SPECIFICATION BS:970.PT.1 1983 GD.605M36
Description : ST.RD.25 MM DIA IN HOT ROLLED & ANNEALED/NORMLISED CONDTION TO SPECIFICATION BS:970.PT.1 1983 GD.605M36()
3) ST ROUND 8 MM DIA
Description : ST ROUND 8 MM DIA()
Specification : ST ROUND 8.00 MM DIA. TO SPECN. BS-970 PT.IIOF 1970 GD. 708 M40 (REQD.FOR-PIN FIRING OF 9MM CARBINE) ACCEPTANCE STANDARDS:MACRO ETCH TEST AS PER ASTME381 & NMIR TEST AS PER IS:4163-82
Specification : STEEL ROUND 25 MM DIA.TO SPECN.IS 5517-1993 GD.42 CN4 MO2 LRS-63MM. IN HOT ROLLED AND ANNEALED CONDITION. TEST PIECE TO BE HEAT TREATED TO "T" CONDITION & MECHANICAL PROPERTIES TO BE CHECKED. ( REQD.FOR CYLINDER GAS )
R
Estab
5) STEEL FLAT 22X18MM FOR MAG
Description : STEEL FLAT 22X18MM FOR MAG()
Specification : SPECN. IS: 5517:1993 DESIGNATION 40 NI 6 CR 4 MO2 (REQD.FOR LINK PISTON EXTN.OF MAG 7.62MM)
Specification : STEEL ROUND 12MM.DIA TO SPECN.BS:970.PT:1.1983.GD 835-M-15 OR GD-655 M-13.(EN-39B OR 36B) REQUIRED FOR EXTRACTOR SMALL ARMS CARTRIDGE TO DRG NO.ARDE/SK-2689/250.
R
Estab
7) STEEL FLAT 32X11MM FOR MAG
Description : STEEL FLAT 32X11MM FOR MAG()
Specification : STEEL FLAT 32X11MM TO SPECN: BS:970: PT-3 1991:GD.835M15 IN HOT ROLLED AND ANNEALED CONDITION REQD. FOR GUIDE FRONT LEFT
R
Estab
8) LEADED PHOS BRONZE ROD 32MM DIA
Description : LEADED PHOS BRONZE ROD 32MM DIA()
Specification : LEADED PHOS.BRONZE ROD 32MM DIA TO SPECN.BS:2874:1969 PB102M
R
Estab
9) SS WIRE ROD DIA 10MM
Description : SS WIRE ROD DIA 10MM()
Specification : SS WIRE ROD DIA 10MM SPEC. IS 6527-1978 GR 04 CR 18 NI 10
R
Estab
Category : s
Grade : 3
Size :
S
1Ordnance Factory Kanpur
[ENR Registration]
Name
Specification
Use
Status
1) forged and annealed steel
Description : forged and annealed steel()
Specification : F & A STEEL ROD 50MM DIA MSF CL XIII/3
R
Estab
2) STEEL STRIP FOR MFG OF VANE
Description : STEEL STRIP FOR MFG OF VANE()
Specification : STEEL STRIP TO SIZE 0.62MM(+0.06MM-0.00)THICK X 121MM (+0.00,-2.0MM) WIDE X 1000(+5MM, -0.00MM) LONG MATERIAL SPECN. STEEL TO IS: 1570 C 15 QUALITY HAVING BEST SURFACE IN COLD ROLLED AND ANNEALED CONDITIOIN & CARBON PERCENTAGE 0.62% MAX
R
Estab
3) STEEL
Description : STEEL()
Specification : STEEL TO SPECN. IS: 7283-1974 WITH PROPERTIES CONFIRMING TO IS:226-1975 TO SIZE : 115(+-1.8)MM DIA.
R
Estab
4) STEEL ROD TO SPECN IS 1570 C 14
Description : STEEL ROD TO SPECN IS 1570 C 14()
Specification : STEEL ROD TO SPECN. IS:1570C14 SIZE 6.50MM (+0.125MM)DIA (STRIKER ROD ARM-1099 C2 , ITEM NO. 2) AS PER DRG NO. SK-9314
Specification : COLD ROLLED BRIGHT ANNEALED STEEL SHEET MADE FROM FULLY KILLED STEEL AS PER BS: 1449 PT 1 1983 GRADE -43/35 SIZE : 95MM+-0.25 WIDE THICKNESS 2.0MM+-0.06X920+15 MM LONG.( PART NO. ITV-46)
R
Estab
7) HOT ROLLED STEEL ROD 35MM
Description : HOT ROLLED STEEL ROD 35MM()
Specification : HOT ROLLED STEEL ROD 35MM (+0.07/-0.13) DIA SPECN. IS:1570 C-15 MN 75 FOR STRIKER HEAD AS PER DRG. NO. SK-6570/A MULTIPLE LENGTH OF 1 MTR
R
Estab
8) CD STEEL ROD 16MM DIA IS 1570 C 15
Description : CD STEEL ROD 16MM DIA IS 1570 C 15()
Specification : CD STEEL ROD 16MM DIA IS 1570 C 15
R
Estab
9) STEEL ROD
Description : STEEL ROD()
Specification : STEEL TO SPECN. IS: 1570 C-15 MN75 COLD DRAWN ROD 9/16" DIA (+0.005" - 0.00) IN LENGTH 12 TO 16FT. (FOR TRANSIT SAFETY PIN) (DRG. NO. ARM-1099-C-3 ITEM NO.7)
R
Estab
10) COLD DRAWN STEEL ROD 28 MM
Description : COLD DRAWN STEEL ROD 28 MM()
Specification : COLD DRAWN STEEL ROD 28 MM (+0.00/-0.13) DIA TO SPECN. IS: 1570, C20 IN 1 MTR LENGTH OR ITS MULTIPLE FOR LUG SUSPENSION (ITEM NO.8) OF ARM- 1099 C3/OFC DRG. NO. SK-6772.
R
Estab
11) STEEL ROD 5MM DIA
Description : STEEL ROD 5MM DIA()
Specification : COLD DRAWN STEEL ROD TO SPECN. IS: 1570, C-20 TO SIZE :5MM (+0.00, -0.125 ) DIA 2.5 MTRS.TO 4 MTRS LONG. HOOK FOR LUG SUSPENSION.
R
Estab
12) Steel rod 85mm dia
Description : Steel rod 85mm dia()
Specification : Steel to specn. IS 1570-13 S-25 or 11 S25 of IS:1570-1979 size 85 mm (+/-1.30) dia in standard length (center plug Arm-1099 C4 Item No. 17) as per Drg. No. SK-9758
R
Estab
13) STEEL STRIP
Description : STEEL STRIP()
Specification : STEEL STRIP TO SIZE: 0.62MM (+0.06MM/-0.00) THICK X218MM (+0MM/-2MM) WIDE X900MM (+5MM/-0MM) LONG MATERIAL SPECN. STEEL TO IS: 1570 C-15 QUALITY HAVING BEST SURFACE IN COLD ROLLED AND ANNEALED CONDITIONS AND C%0.20% MAX (FOR MANUFACTURING
R
Estab
14) BRASS TUBE
Description : BRASS TUBE()
Specification : BRASS TUBE TO SIZE : O/D 9.53+/-0.076MM X 0.71MM WT IN MULTIPLE LENGTH OF 115MM TO SPECN. IS:407-1966 ALLOY-1 IN ANNEALED CONDITION OF STD. FOR CENTRAL TUBE
(DRG. NO. ARM-1099C4 ITEM NO.19)
R
Estab
15) MS ROUND
Description : MS ROUND()
Specification : STEEL TO SPECN. IS:1570,C 20 COLD DRAWN ROD 1-1/4" (+0.004") IE 31.75MM DIA IN STANDARD LENGTH ( TAIL PLUG ARM -1099C4 ITEM NO. 20 AS PER OFC DRG. NO. SK-9757
R
Estab
16) FORGED TO DIA 229
Description : FORGED TO DIA 229()
Specification : FORGED TO DIA 229(+20MM) IN LENGTH OF 1 TO 1.5 METERS AS PER GR.MSF IX/3 (%C -0.95-1.15, SI -0.15-0.25, MN -2.0-2.5, S -0.03MAX, P-0.03MAX-CR.-0.3MAX) OR T90MN2W50CR45 AS PER IS:1570-1961)
Specification : STEEL FORGED ROUND 152MM DIA USUAL FORGING TOLERANCE IN LENGTH OF 1 TO 3 METERS MSF CL. IX/3 (%C-0.95-1.15, SI-0.15-0.25, MN-2.0-2.5, S-0.03 MAX P-0.03MAX, CR-0.3MAX) OR T90MN2W50CR45 AS PER IS: 1570-1961
R
Estab
18) STEEL ROD OF DIA 175MM
Description : STEEL ROD OF DIA 175MM()
Specification : STEEL ROD OF DIA 175MM X 60MM LENGTH OR ITS MULTIPLE LENGTH TO SPECN: IS:3749-1978 XT215 CR12 IN FORGED ANNEALED , SKIN TURN AND ULTRASONCALLY SOUND CONDITION, AS PER IS: 8791-1978
R
Estab
19) STEEL ROD 102
Description : STEEL ROD 102()
Specification : STEEL ROD 102 (+10)MM (4") DIA IN LENGTH OF 1 MTR TO 2 MTRS CLASS -IX/3 (%C-0.95-1.15, SI-0.15-0.25, MN -2.0-2.5,S-0.03MAX. P-0.03MAX, CR-0.03MAX) OR T90MN2W50CR45 AS PER IS: 1570-1961
R
Estab
20) STEEL ROD 200 DIA
Description : STEEL ROD 200 DIA()
Specification : STEEL ROD 200 DIA (+0/-5MM) (IS: 3749-1978-XT-215 CR12 IN 350MM LENGTH & ABOVE
R
Estab
21) STEEL ROD 108MM
Description : STEEL ROD 108MM()
Specification : STEEL ROD 108 MM (+10MM) DIA TO SPECIFICATION MSF CL. IX/3 OF T90MN2W50CR45 AS PER IS: 1570-1961 IN LENGTH OF 1-2 MTR (FORGED AND ANNEALED)
R
Estab
22) STEEL ROD 3 INCH DIA
Description : STEEL ROD 3 INCH DIA()
Specification : STEEL ROD IN FORGED & ANNEALED CONDITION AS PER SIZE: & SPECN. RD77MM(3") DIA TO MSF CL XIII/3 OR T103 AS PER IS: 1570-1961
R
Estab
23) STEEL F AND A ROD 210 DIA X70MM SAE H10
Description : STEEL F AND A ROD 210 DIA X70MM SAE H10()
Specification : STEEL FORGED & ANNEALED ROD 210 (+/-2 MM) DIA X 70 MM (+5MM) OR ITS MULTIPLE LENGTH OF 1 TO 2 METRE TO SPECN. SAEH -10 IN ROUGH MACHINED & ULTRASONICALLY SOUND CONDITION AS PER IS: 8791-1978 CLAUSE 9.1(A).
R
Estab
24) STEEL FLAT
Description : STEEL FLAT()
Specification : STEEL FLAT TO SIZE 12MM X 300MM TO SPECN. T-105CR5MN2 OF IS: 3749-1978 OR BS: 970 EN -31 IN LENGTH OF ONE TO TWO MTRS.
R
Estab
25) HSS ROUND 20 MM DIA ASP 30
Description : HSS ROUND 20 MM DIA ASP 30()
Specification : HIGH SPEED STEEL ROUND 20 MM DIA TO SPECN. ASP-30 TOLERANCE AS PER IS: 10604 (PART-I) 1983.
R
Estab
26) MS FLAT
Description : MS FLAT()
Specification : MS FLAT 8MM X 200MM X1250MM AS PER IS: 5517-1978
R
Estab
27) Steel Flat to size 10mmX200mm in length of one meter
Description : Steel Flat to size 10mmX200mm in length of one meter()
Specification : MSF Class IX/3 or XII I/3 In forged & machined condition(Chemical composition: C-0.85-0.95%,SI-0.15-0.25%,MN-2.00-2.5%,S-0.03%,P- 0.03%,CR - 0.3%
R
Estab
28) FORGED AND ANNEALED STEEL ROD
Description : FORGED AND ANNEALED STEEL ROD()
Specification : FORGED AND ANNEALED STEEL ROD OF DIA 83MM (+10MM) IN LENGTH OF 1 TO 2 METER & GR. MSF IX/3 OR T90MN2W50CR45 AS PER IS: 1570-1961
R
Estab
29) COPPER 99 PERCENT PURE SIZE 40MM SQR
Description : COPPER 99 PERCENT PURE SIZE 40MM SQR()
Specification : COPPER 99 PERCENT PURE SIZE 40MM SQR
R
Estab
Category : p
Grade : 2
Size :
M
1Ordnance Factory Kanpur
[ENR Registration]
Name
Specification
Use
Status
1) forged and annealed steel
Description : forged and annealed steel()
Specification : F & A STEEL ROD 50MM DIA MSF CL XIII/3
R
Estab
2) STEEL STRIP FOR MFG OF VANE
Description : STEEL STRIP FOR MFG OF VANE()
Specification : STEEL STRIP TO SIZE 0.62MM(+0.06MM-0.00)THICK X 121MM (+0.00,-2.0MM) WIDE X 1000(+5MM, -0.00MM) LONG MATERIAL SPECN. STEEL TO IS: 1570 C 15 QUALITY HAVING BEST SURFACE IN COLD ROLLED AND ANNEALED CONDITIOIN & CARBON PERCENTAGE 0.62% MAX
R
Estab
3) STEEL
Description : STEEL()
Specification : STEEL TO SPECN. IS: 7283-1974 WITH PROPERTIES CONFIRMING TO IS:226-1975 TO SIZE : 115(+-1.8)MM DIA.
R
Estab
4) STEEL ROD TO SPECN IS 1570 C 14
Description : STEEL ROD TO SPECN IS 1570 C 14()
Specification : STEEL ROD TO SPECN. IS:1570C14 SIZE 6.50MM (+0.125MM)DIA (STRIKER ROD ARM-1099 C2 , ITEM NO. 2) AS PER DRG NO. SK-9314
Specification : COLD ROLLED BRIGHT ANNEALED STEEL SHEET MADE FROM FULLY KILLED STEEL AS PER BS: 1449 PT 1 1983 GRADE -43/35 SIZE : 95MM+-0.25 WIDE THICKNESS 2.0MM+-0.06X920+15 MM LONG.( PART NO. ITV-46)
R
Estab
7) HOT ROLLED STEEL ROD 35MM
Description : HOT ROLLED STEEL ROD 35MM()
Specification : HOT ROLLED STEEL ROD 35MM (+0.07/-0.13) DIA SPECN. IS:1570 C-15 MN 75 FOR STRIKER HEAD AS PER DRG. NO. SK-6570/A MULTIPLE LENGTH OF 1 MTR
R
Estab
8) CD STEEL ROD 16MM DIA IS 1570 C 15
Description : CD STEEL ROD 16MM DIA IS 1570 C 15()
Specification : CD STEEL ROD 16MM DIA IS 1570 C 15
R
Estab
9) STEEL ROD
Description : STEEL ROD()
Specification : STEEL TO SPECN. IS: 1570 C-15 MN75 COLD DRAWN ROD 9/16" DIA (+0.005" - 0.00) IN LENGTH 12 TO 16FT. (FOR TRANSIT SAFETY PIN) (DRG. NO. ARM-1099-C-3 ITEM NO.7)
R
Estab
10) COLD DRAWN STEEL ROD 28 MM
Description : COLD DRAWN STEEL ROD 28 MM()
Specification : COLD DRAWN STEEL ROD 28 MM (+0.00/-0.13) DIA TO SPECN. IS: 1570, C20 IN 1 MTR LENGTH OR ITS MULTIPLE FOR LUG SUSPENSION (ITEM NO.8) OF ARM- 1099 C3/OFC DRG. NO. SK-6772.
R
Estab
11) STEEL ROD 5MM DIA
Description : STEEL ROD 5MM DIA()
Specification : COLD DRAWN STEEL ROD TO SPECN. IS: 1570, C-20 TO SIZE :5MM (+0.00, -0.125 ) DIA 2.5 MTRS.TO 4 MTRS LONG. HOOK FOR LUG SUSPENSION.
R
Estab
12) Steel rod 85mm dia
Description : Steel rod 85mm dia()
Specification : Steel to specn. IS 1570-13 S-25 or 11 S25 of IS:1570-1979 size 85 mm (+/-1.30) dia in standard length (center plug Arm-1099 C4 Item No. 17) as per Drg. No. SK-9758
R
Estab
13) STEEL STRIP
Description : STEEL STRIP()
Specification : STEEL STRIP TO SIZE: 0.62MM (+0.06MM/-0.00) THICK X218MM (+0MM/-2MM) WIDE X900MM (+5MM/-0MM) LONG MATERIAL SPECN. STEEL TO IS: 1570 C-15 QUALITY HAVING BEST SURFACE IN COLD ROLLED AND ANNEALED CONDITIONS AND C%0.20% MAX (FOR MANUFACTURING
R
Estab
14) BRASS TUBE
Description : BRASS TUBE()
Specification : BRASS TUBE TO SIZE : O/D 9.53+/-0.076MM X 0.71MM WT IN MULTIPLE LENGTH OF 115MM TO SPECN. IS:407-1966 ALLOY-1 IN ANNEALED CONDITION OF STD. FOR CENTRAL TUBE
(DRG. NO. ARM-1099C4 ITEM NO.19)
R
Estab
15) MS ROUND
Description : MS ROUND()
Specification : STEEL TO SPECN. IS:1570,C 20 COLD DRAWN ROD 1-1/4" (+0.004") IE 31.75MM DIA IN STANDARD LENGTH ( TAIL PLUG ARM -1099C4 ITEM NO. 20 AS PER OFC DRG. NO. SK-9757
R
Estab
16) FORGED TO DIA 229
Description : FORGED TO DIA 229()
Specification : FORGED TO DIA 229(+20MM) IN LENGTH OF 1 TO 1.5 METERS AS PER GR.MSF IX/3 (%C -0.95-1.15, SI -0.15-0.25, MN -2.0-2.5, S -0.03MAX, P-0.03MAX-CR.-0.3MAX) OR T90MN2W50CR45 AS PER IS:1570-1961)
Specification : STEEL FORGED ROUND 152MM DIA USUAL FORGING TOLERANCE IN LENGTH OF 1 TO 3 METERS MSF CL. IX/3 (%C-0.95-1.15, SI-0.15-0.25, MN-2.0-2.5, S-0.03 MAX P-0.03MAX, CR-0.3MAX) OR T90MN2W50CR45 AS PER IS: 1570-1961
R
Estab
18) STEEL ROD OF DIA 175MM
Description : STEEL ROD OF DIA 175MM()
Specification : STEEL ROD OF DIA 175MM X 60MM LENGTH OR ITS MULTIPLE LENGTH TO SPECN: IS:3749-1978 XT215 CR12 IN FORGED ANNEALED , SKIN TURN AND ULTRASONCALLY SOUND CONDITION, AS PER IS: 8791-1978
R
Estab
19) STEEL ROD 102
Description : STEEL ROD 102()
Specification : STEEL ROD 102 (+10)MM (4") DIA IN LENGTH OF 1 MTR TO 2 MTRS CLASS -IX/3 (%C-0.95-1.15, SI-0.15-0.25, MN -2.0-2.5,S-0.03MAX. P-0.03MAX, CR-0.03MAX) OR T90MN2W50CR45 AS PER IS: 1570-1961
R
Estab
20) STEEL ROD 200 DIA
Description : STEEL ROD 200 DIA()
Specification : STEEL ROD 200 DIA (+0/-5MM) (IS: 3749-1978-XT-215 CR12 IN 350MM LENGTH & ABOVE
R
Estab
21) STEEL ROD 108MM
Description : STEEL ROD 108MM()
Specification : STEEL ROD 108 MM (+10MM) DIA TO SPECIFICATION MSF CL. IX/3 OF T90MN2W50CR45 AS PER IS: 1570-1961 IN LENGTH OF 1-2 MTR (FORGED AND ANNEALED)
R
Estab
22) STEEL ROD 3 INCH DIA
Description : STEEL ROD 3 INCH DIA()
Specification : STEEL ROD IN FORGED & ANNEALED CONDITION AS PER SIZE: & SPECN. RD77MM(3") DIA TO MSF CL XIII/3 OR T103 AS PER IS: 1570-1961
R
Estab
23) STEEL F AND A ROD 210 DIA X70MM SAE H10
Description : STEEL F AND A ROD 210 DIA X70MM SAE H10()
Specification : STEEL FORGED & ANNEALED ROD 210 (+/-2 MM) DIA X 70 MM (+5MM) OR ITS MULTIPLE LENGTH OF 1 TO 2 METRE TO SPECN. SAEH -10 IN ROUGH MACHINED & ULTRASONICALLY SOUND CONDITION AS PER IS: 8791-1978 CLAUSE 9.1(A).
R
Estab
24) STEEL FLAT
Description : STEEL FLAT()
Specification : STEEL FLAT TO SIZE 12MM X 300MM TO SPECN. T-105CR5MN2 OF IS: 3749-1978 OR BS: 970 EN -31 IN LENGTH OF ONE TO TWO MTRS.
R
Estab
25) HSS ROUND 20 MM DIA ASP 30
Description : HSS ROUND 20 MM DIA ASP 30()
Specification : HIGH SPEED STEEL ROUND 20 MM DIA TO SPECN. ASP-30 TOLERANCE AS PER IS: 10604 (PART-I) 1983.
R
Estab
26) MS FLAT
Description : MS FLAT()
Specification : MS FLAT 8MM X 200MM X1250MM AS PER IS: 5517-1978
R
Estab
27) Steel Flat to size 10mmX200mm in length of one meter
Description : Steel Flat to size 10mmX200mm in length of one meter()
Specification : MSF Class IX/3 or XII I/3 In forged & machined condition(Chemical composition: C-0.85-0.95%,SI-0.15-0.25%,MN-2.00-2.5%,S-0.03%,P- 0.03%,CR - 0.3%
R
Estab
28) FORGED AND ANNEALED STEEL ROD
Description : FORGED AND ANNEALED STEEL ROD()
Specification : FORGED AND ANNEALED STEEL ROD OF DIA 83MM (+10MM) IN LENGTH OF 1 TO 2 METER & GR. MSF IX/3 OR T90MN2W50CR45 AS PER IS: 1570-1961
R
Estab
29) COPPER 99 PERCENT PURE SIZE 40MM SQR
Description : COPPER 99 PERCENT PURE SIZE 40MM SQR()
Specification : COPPER 99 PERCENT PURE SIZE 40MM SQR
R
Estab
Category : p
Grade : 2
Size :
M
1Field Gun Factory Kanpur
[ENR Registration]
Name
Specification
Use
Status
1) ST. STEEL SHEETS
Description : ST. STEEL SHEETS()
Specification : STEEL SHEET SIZE - 55 X6MM THICK
R
Estab
2) PHOSPHER BRONZE, GUN METAL, TIN BRONGE TO ALL STANDARD SPECIFICATION IN THE FORM OF ROUND, SQUARE, R
Description : PHOSPHER BRONZE, GUN METAL, TIN BRONGE TO ALL STANDARD SPECIFICATION IN THE FORM OF ROUND, SQUARE, R()
Specification : PHOSPHER BRONZE SIZE: 45 MM SQUARE
R
Estab
Category : p
Grade : 3
Size :
S
1Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) ST SHEET 1.00X1250X2500MM DD QUALITY. (COLD ROLLED ) TO SPECIFICATION IS:513-(LATEST ISSUE).
Description : ST SHEET 1.00X1250X2500MM DD QUALITY. (COLD ROLLED ) TO SPECIFICATION IS:513-(LATEST ISSUE).()
2) STEEL RD 32MM DIA IN HOT ROLLED AND NORMALISED CONDITION TO SPECN.IS-1875-2005 DESIGNATION C8 CLASS 2 LATEST ISSUE
Description : STEEL RD 32MM DIA IN HOT ROLLED AND NORMALISED CONDITION TO SPECN.IS-1875-2005 DESIGNATION C8 CLASS 2 LATEST ISSUE()
Specification : SPECN.IS-1875-2005 DESIGNATION C8 CLASS 2 LATEST ISSUE
R
Estab
3) STEEL RD 8MM DIA FOR MAG
Description : STEEL RD 8MM DIA FOR MAG()
Specification : BS 970 PT 1:1983 GR 431 S-29 OR 20 S-37 EN 56C
R
Estab
4) ST STRIP FOR LMG
Description : ST STRIP FOR LMG()
Specification : ST. STRIP 1.8 MM THICK X 72 MM X 1050 MM LENGTH WITH GRAINS IN LENGTH-WISE DIRECTION TO SPECN. STEEL IS:7226-1974,DESIGNATION C 40 (FOR BRACKET FRONT).
R
Estab
5) STEEL RD 13MM DIA IN ANNEALED AND COLD DRAWN CONDITION
Description : STEEL RD 13MM DIA IN ANNEALED AND COLD DRAWN CONDITION()
Specification : STEEL RD 13MM DIA IN ANNEALED AND COLD DRAWN CONDITION TO SPECN.BS:970:PT.1:SEC-2-1983 GD 080M40 TEST PIECE TO BE TESTED AS PER SPECIFIC.MATERIAL SHOULD ALSO SATISFY THE TEST AS LAID DOWN IN THE ANNEXURE.
Specification : STEEL ROUND 20MM DIA TO SPECN.BS:970:PT.1:1983 GD.080M40 IN HOT ROLLED &NORMALISED CONDITION. TEST PIECE TO BE TESTED AS PER THE SPECIFICATION.
R
Estab
7) STEEL FLATS
Description : STEEL FLATS()
Specification : AS PER SPECIFICATION
R
Estab
8) ST.FLAT 40X16MM TO SPECN.IS:5517-1993 DEGIGNATION 40 CB . (FOR BRACKET FRONT HAND GUARD).
Description : ST.FLAT 40X16MM TO SPECN.IS:5517-1993 DEGIGNATION 40 CB . (FOR BRACKET FRONT HAND GUARD).()
11) STEEL RD 25 MM DIA ( REQUIRED FOR GAS REGULATOR DS CAT NO. 1005-006614)
Description : STEEL RD 25 MM DIA ( REQUIRED FOR GAS REGULATOR DS CAT NO. 1005-006614)()
Specification : SPECN BS: 970:PT-3:1991 GD.420S29 OR 431 S29
Specification : STEEL ROUND 27 MM TO SPECN.IS:5517-1993 DEGIGNATION 55C8 IN ANNEALED & COLD DRAWN CONDN. (FOR SLEEVE LOCKING BIPOD).
R
Estab
13) STEEL RD 45MM DIA IN HR AND NORMALISED CONDITION OF MAG
Description : STEEL RD 45MM DIA IN HR AND NORMALISED CONDITION OF MAG()
Specification : SPECN.BS:970PT-3:1991.GD.070M55.TEST PIECE TO BETESTED AS PER SPECN.MATL. SHOULD ALSO SATISFY THE TEST AS PER ANNX."A".A SEPERATE TESTPIECES IS TO BE QUENCHED * TEMPERED TO ACHIEVE HARDNESS40-45HRC. (REQD.FOR-BARREL LOCKING NUT )
R
Estab
14) STEEL ROD 30MM DIA. TO SPECN.BS:970:PT.1:1983 GD.070M55 CONDN.'S' (REQD. FOR FLASH HIDER )
Description : STEEL ROD 30MM DIA. TO SPECN.BS:970:PT.1:1983 GD.070M55 CONDN.'S' (REQD. FOR FLASH HIDER )()
15) SS WIRE ROD DIA 10MM
Description : SS WIRE ROD DIA 10MM()
Specification : SS WIRE ROD DIA 10MM SPEC. IS 6527-1978 GR 04 CR 18 NI 10
R
Estab
16) ST.FLAT 125 X 8 X 530 MM LONG IN CUT LENGTH IN H.R & NORM. CONDN. TO SPECN.IS:5517-1993
Description : ST.FLAT 125 X 8 X 530 MM LONG IN CUT LENGTH IN H.R & NORM. CONDN. TO SPECN.IS:5517-1993()
Specification : ST.FLAT 125 X 8 X 530 MM LONG IN CUT LENGTH IN H.R & NORM. CONDN. TO SPECN.IS:5517-1993 DESIGNATION 55C8 TEST PIECE TO BE TESTED AS PER SPECN.TOLLERANCE ON WIDTH +/-2MM,ON THICKNE
SS +/-0.25MM.
18) STEEL FLAT TO SPECIFICATION BS:970:PT.3:1991: 070 M55 SIZE 45MM X 50MM IN FORGED AND ANNEALED CONDITION
Description : STEEL FLAT TO SPECIFICATION BS:970:PT.3:1991: 070 M55 SIZE 45MM X 50MM IN FORGED AND ANNEALED CONDITION()
Specification : SPECIFICATION BS:970:PT.3:1991: 070 M55 SIZE 45MM X 50MM IN FORGED AND ANNEALED CONDITION
R
Estab
19) Spring Steel Wire for Striker Mechanism
Description : Spring Steel Wire for Striker Mechanism()
Specification : Spring Steel Wire dia 1.1MM for Striker Mechanism, Material Spec IV.STA 3 or 4 or IS:4454:2001,SL or BS:1408:1964. 1408-C for Spring as per Drg. ANO.NAD 7606/5
R
Estab
20) SPRING STEEL WIRE FOR CARBINE 5 56
Description : SPRING STEEL WIRE FOR CARBINE 5 56()
Specification : SPRING STEEL WIRE DIA. 1.30MM TO SPECN- IS:4454:PT-1:2001GD-DH WITH UTS VALUE MIN 2300N/MM2
R
Estab
21) ST WIRE SPG 15 SWG(1.829MM)DIA TO SPECN IS:4454:PART1:2001 GRADE "DM" REQUIRED FOR SPRING RETURN OUTER OF 9MM CARBINE.
Description : ST WIRE SPG 15 SWG(1.829MM)DIA TO SPECN IS:4454:PART1:2001 GRADE "DM" REQUIRED FOR SPRING RETURN OUTER OF 9MM CARBINE.()
22) STEEL RD 22MM DIA IN HOT ROLLED AND ANNEALED CONDITION TO SPECN.BS:970 PT.1:1983 GD.817M40 OR 826M40.
Description : STEEL RD 22MM DIA IN HOT ROLLED AND ANNEALED CONDITION TO SPECN.BS:970 PT.1:1983 GD.817M40 OR 826M40.()
Specification : SPECN.BS:970 PT.1:1983 GD.817M40 OR 826M40.
R
Estab
23) ST RD 22MM DIA IN HOT ROLLED AND ANNEALED CONDITION
Description : ST RD 22MM DIA IN HOT ROLLED AND ANNEALED CONDITION()
Specification : ST.RD.22MM DIA IN HOT ROLLED & ANNEALED CONDITION TO SPECN IS:6527:1995,DESIGNATION X30CR 13 (FOR PLUG GAS).
R
Estab
24) STEEL FLAT 70 X 34 MM IN HOT ROLLED and ANNEALED CONDITION
Description : STEEL FLAT 70 X 34 MM IN HOT ROLLED and ANNEALED CONDITION()
Specification : SPECN.BS:970:PT-3:1991.GD.410S21 OR 420S29.TEST PIECE TO BE TESTEDAS PER RULINF SECTION. MATL.SHOULD SATISFY MACRO-ETCH TEST &MICROSCOPIC NON-METALIC INCLUSION RATING AS PER NATURE-C A SEPARATE T.P.TO BE HARDNED TO ACHIEVE HARDNESS 265-
R
Estab
25) STEEL RD 12MM DIA IN ANNEALED AND COLD DRAWN CONDITION TO SPECN.BS:970.PT-I:1983 GD.817M40 OR 826M40 (REQD.FOR EXTRACTOR PLUNGER OF MAG 7.62MM)
Description : STEEL RD 12MM DIA IN ANNEALED AND COLD DRAWN CONDITION TO SPECN.BS:970.PT-I:1983 GD.817M40 OR 826M40 (REQD.FOR EXTRACTOR PLUNGER OF MAG 7.62MM)()
Specification : SPECN.BS:970.PT-I:1983 GD.817M40 OR 826M40
R
Estab
26) STEEL FLAT 17X47MM IN HOT ROLLED AND ANNEALED AT 650 C
Description : STEEL FLAT 17X47MM IN HOT ROLLED AND ANNEALED AT 650 C()
Specification : SPECN.BS:970:PT-3:1991 GD.945M38 T.P.TESTED IN `T'CONDITION MACRO ETCH TEST & NMIR TEST AS PER ANNEXURE-A NATURE-C.(REQD.FOR-SHOULDER LOCKING LEFT & RIGHT DS CAT 1005-007907)
R
Estab
27) STEEL SQR 37MM FOR MAG
Description : STEEL SQR 37MM FOR MAG()
Specification : SPECN.BS:970:PT-1:1983 GD.945M38 IN HOT ROLLED & NORMALISED CONDITION TEST PIECE TO BE TESTED IN `T' CONDTION
R
Estab
28) STEEL RD 45MM DIA IN HR AND NORMALISED CONDITION
Description : STEEL RD 45MM DIA IN HR AND NORMALISED CONDITION()
Specification : SPECN.BS:970PT -3:1991.GD.070M55.TEST PIECE TO BETESTED AS PER SPECN.MATL. SHOULD ALSO SATISFY THE TEST AS PER ANNX."C".A SEPERATE TEST PIECES IS TO BE QUENCHED * TEMPERED TO ACHIEVE HARDNESS40-45 HRC. (REQD.FOR-BARREL LOCKING NUT )
R
Estab
29) ST ROUND 8 MM DIA
Description : ST ROUND 8 MM DIA()
Specification : ST ROUND 8.00 MM DIA. TO SPECN. BS-970 PT.IIOF 1970 GD. 708 M40 (REQD.FOR-PIN FIRING OF 9MM CARBINE) ACCEPTANCE STANDARDS:MACRO ETCH TEST AS PER ASTME381 & NMIR TEST AS PER IS:4163-82
R
Estab
30) STEEL ROUND 18MM DIA FOR MAG
Description : STEEL ROUND 18MM DIA FOR MAG()
2) STEEL RD 32MM DIA IN HOT ROLLED AND NORMALISED CONDITION TO SPECN.IS-1875-2005 DESIGNATION C8 CLASS 2 LATEST ISSUE
Description : STEEL RD 32MM DIA IN HOT ROLLED AND NORMALISED CONDITION TO SPECN.IS-1875-2005 DESIGNATION C8 CLASS 2 LATEST ISSUE()
Specification : SPECN.IS-1875-2005 DESIGNATION C8 CLASS 2 LATEST ISSUE
R
Estab
3) STEEL RD 8MM DIA FOR MAG
Description : STEEL RD 8MM DIA FOR MAG()
Specification : BS 970 PT 1:1983 GR 431 S-29 OR 20 S-37 EN 56C
R
Estab
4) ST STRIP FOR LMG
Description : ST STRIP FOR LMG()
Specification : ST. STRIP 1.8 MM THICK X 72 MM X 1050 MM LENGTH WITH GRAINS IN LENGTH-WISE DIRECTION TO SPECN. STEEL IS:7226-1974,DESIGNATION C 40 (FOR BRACKET FRONT).
R
Estab
5) STEEL RD 13MM DIA IN ANNEALED AND COLD DRAWN CONDITION
Description : STEEL RD 13MM DIA IN ANNEALED AND COLD DRAWN CONDITION()
Specification : STEEL RD 13MM DIA IN ANNEALED AND COLD DRAWN CONDITION TO SPECN.BS:970:PT.1:SEC-2-1983 GD 080M40 TEST PIECE TO BE TESTED AS PER SPECIFIC.MATERIAL SHOULD ALSO SATISFY THE TEST AS LAID DOWN IN THE ANNEXURE.
Specification : STEEL ROUND 20MM DIA TO SPECN.BS:970:PT.1:1983 GD.080M40 IN HOT ROLLED &NORMALISED CONDITION. TEST PIECE TO BE TESTED AS PER THE SPECIFICATION.
R
Estab
7) STEEL FLATS
Description : STEEL FLATS()
Specification : AS PER SPECIFICATION
R
Estab
8) ST.FLAT 40X16MM TO SPECN.IS:5517-1993 DEGIGNATION 40 CB . (FOR BRACKET FRONT HAND GUARD).
Description : ST.FLAT 40X16MM TO SPECN.IS:5517-1993 DEGIGNATION 40 CB . (FOR BRACKET FRONT HAND GUARD).()
11) STEEL RD 25 MM DIA ( REQUIRED FOR GAS REGULATOR DS CAT NO. 1005-006614)
Description : STEEL RD 25 MM DIA ( REQUIRED FOR GAS REGULATOR DS CAT NO. 1005-006614)()
Specification : SPECN BS: 970:PT-3:1991 GD.420S29 OR 431 S29
Specification : STEEL ROUND 27 MM TO SPECN.IS:5517-1993 DEGIGNATION 55C8 IN ANNEALED & COLD DRAWN CONDN. (FOR SLEEVE LOCKING BIPOD).
R
Estab
13) STEEL RD 45MM DIA IN HR AND NORMALISED CONDITION OF MAG
Description : STEEL RD 45MM DIA IN HR AND NORMALISED CONDITION OF MAG()
Specification : SPECN.BS:970PT-3:1991.GD.070M55.TEST PIECE TO BETESTED AS PER SPECN.MATL. SHOULD ALSO SATISFY THE TEST AS PER ANNX."A".A SEPERATE TESTPIECES IS TO BE QUENCHED * TEMPERED TO ACHIEVE HARDNESS40-45HRC. (REQD.FOR-BARREL LOCKING NUT )
R
Estab
14) STEEL ROD 30MM DIA. TO SPECN.BS:970:PT.1:1983 GD.070M55 CONDN.'S' (REQD. FOR FLASH HIDER )
Description : STEEL ROD 30MM DIA. TO SPECN.BS:970:PT.1:1983 GD.070M55 CONDN.'S' (REQD. FOR FLASH HIDER )()
15) SS WIRE ROD DIA 10MM
Description : SS WIRE ROD DIA 10MM()
Specification : SS WIRE ROD DIA 10MM SPEC. IS 6527-1978 GR 04 CR 18 NI 10
R
Estab
16) ST.FLAT 125 X 8 X 530 MM LONG IN CUT LENGTH IN H.R & NORM. CONDN. TO SPECN.IS:5517-1993
Description : ST.FLAT 125 X 8 X 530 MM LONG IN CUT LENGTH IN H.R & NORM. CONDN. TO SPECN.IS:5517-1993()
Specification : ST.FLAT 125 X 8 X 530 MM LONG IN CUT LENGTH IN H.R & NORM. CONDN. TO SPECN.IS:5517-1993 DESIGNATION 55C8 TEST PIECE TO BE TESTED AS PER SPECN.TOLLERANCE ON WIDTH +/-2MM,ON THICKNE
SS +/-0.25MM.
18) STEEL FLAT TO SPECIFICATION BS:970:PT.3:1991: 070 M55 SIZE 45MM X 50MM IN FORGED AND ANNEALED CONDITION
Description : STEEL FLAT TO SPECIFICATION BS:970:PT.3:1991: 070 M55 SIZE 45MM X 50MM IN FORGED AND ANNEALED CONDITION()
Specification : SPECIFICATION BS:970:PT.3:1991: 070 M55 SIZE 45MM X 50MM IN FORGED AND ANNEALED CONDITION
R
Estab
19) Spring Steel Wire for Striker Mechanism
Description : Spring Steel Wire for Striker Mechanism()
Specification : Spring Steel Wire dia 1.1MM for Striker Mechanism, Material Spec IV.STA 3 or 4 or IS:4454:2001,SL or BS:1408:1964. 1408-C for Spring as per Drg. ANO.NAD 7606/5
R
Estab
20) SPRING STEEL WIRE FOR CARBINE 5 56
Description : SPRING STEEL WIRE FOR CARBINE 5 56()
Specification : SPRING STEEL WIRE DIA. 1.30MM TO SPECN- IS:4454:PT-1:2001GD-DH WITH UTS VALUE MIN 2300N/MM2
R
Estab
21) ST WIRE SPG 15 SWG(1.829MM)DIA TO SPECN IS:4454:PART1:2001 GRADE "DM" REQUIRED FOR SPRING RETURN OUTER OF 9MM CARBINE.
Description : ST WIRE SPG 15 SWG(1.829MM)DIA TO SPECN IS:4454:PART1:2001 GRADE "DM" REQUIRED FOR SPRING RETURN OUTER OF 9MM CARBINE.()
22) STEEL RD 22MM DIA IN HOT ROLLED AND ANNEALED CONDITION TO SPECN.BS:970 PT.1:1983 GD.817M40 OR 826M40.
Description : STEEL RD 22MM DIA IN HOT ROLLED AND ANNEALED CONDITION TO SPECN.BS:970 PT.1:1983 GD.817M40 OR 826M40.()
Specification : SPECN.BS:970 PT.1:1983 GD.817M40 OR 826M40.
R
Estab
23) ST RD 22MM DIA IN HOT ROLLED AND ANNEALED CONDITION
Description : ST RD 22MM DIA IN HOT ROLLED AND ANNEALED CONDITION()
Specification : ST.RD.22MM DIA IN HOT ROLLED & ANNEALED CONDITION TO SPECN IS:6527:1995,DESIGNATION X30CR 13 (FOR PLUG GAS).
R
Estab
24) STEEL FLAT 70 X 34 MM IN HOT ROLLED and ANNEALED CONDITION
Description : STEEL FLAT 70 X 34 MM IN HOT ROLLED and ANNEALED CONDITION()
Specification : SPECN.BS:970:PT-3:1991.GD.410S21 OR 420S29.TEST PIECE TO BE TESTEDAS PER RULINF SECTION. MATL.SHOULD SATISFY MACRO-ETCH TEST &MICROSCOPIC NON-METALIC INCLUSION RATING AS PER NATURE-C A SEPARATE T.P.TO BE HARDNED TO ACHIEVE HARDNESS 265-
R
Estab
25) STEEL RD 12MM DIA IN ANNEALED AND COLD DRAWN CONDITION TO SPECN.BS:970.PT-I:1983 GD.817M40 OR 826M40 (REQD.FOR EXTRACTOR PLUNGER OF MAG 7.62MM)
Description : STEEL RD 12MM DIA IN ANNEALED AND COLD DRAWN CONDITION TO SPECN.BS:970.PT-I:1983 GD.817M40 OR 826M40 (REQD.FOR EXTRACTOR PLUNGER OF MAG 7.62MM)()
Specification : SPECN.BS:970.PT-I:1983 GD.817M40 OR 826M40
R
Estab
26) STEEL FLAT 17X47MM IN HOT ROLLED AND ANNEALED AT 650 C
Description : STEEL FLAT 17X47MM IN HOT ROLLED AND ANNEALED AT 650 C()
Specification : SPECN.BS:970:PT-3:1991 GD.945M38 T.P.TESTED IN `T'CONDITION MACRO ETCH TEST & NMIR TEST AS PER ANNEXURE-A NATURE-C.(REQD.FOR-SHOULDER LOCKING LEFT & RIGHT DS CAT 1005-007907)
R
Estab
27) STEEL SQR 37MM FOR MAG
Description : STEEL SQR 37MM FOR MAG()
Specification : SPECN.BS:970:PT-1:1983 GD.945M38 IN HOT ROLLED & NORMALISED CONDITION TEST PIECE TO BE TESTED IN `T' CONDTION
R
Estab
28) STEEL RD 45MM DIA IN HR AND NORMALISED CONDITION
Description : STEEL RD 45MM DIA IN HR AND NORMALISED CONDITION()
Specification : SPECN.BS:970PT -3:1991.GD.070M55.TEST PIECE TO BETESTED AS PER SPECN.MATL. SHOULD ALSO SATISFY THE TEST AS PER ANNX."C".A SEPERATE TEST PIECES IS TO BE QUENCHED * TEMPERED TO ACHIEVE HARDNESS40-45 HRC. (REQD.FOR-BARREL LOCKING NUT )
R
Estab
29) ST ROUND 8 MM DIA
Description : ST ROUND 8 MM DIA()
Specification : ST ROUND 8.00 MM DIA. TO SPECN. BS-970 PT.IIOF 1970 GD. 708 M40 (REQD.FOR-PIN FIRING OF 9MM CARBINE) ACCEPTANCE STANDARDS:MACRO ETCH TEST AS PER ASTME381 & NMIR TEST AS PER IS:4163-82
R
Estab
30) STEEL ROUND 18MM DIA FOR MAG
Description : STEEL ROUND 18MM DIA FOR MAG()
31) STEEL TO BS:970PT-1:1983 835 M15 OR EN-39B SQUARE 90 MM
Description : STEEL TO BS:970PT-1:1983 835 M15 OR EN-39B SQUARE 90 MM()
Specification : AS PER DRG.
R
Estab
32) STEEL FLAT 32X11MM FOR MAG
Description : STEEL FLAT 32X11MM FOR MAG()
Specification : STEEL FLAT 32X11MM TO SPECN: BS:970: PT-3 1991:GD.835M15 IN HOT ROLLED AND ANNEALED CONDITION REQD. FOR GUIDE FRONT LEFT
R
Estab
Category : s
Grade : 3
Size :
S
1Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) DIA 64MM+/-0.5MM STEEL ROD
Description : DIA 64MM+/-0.5MM STEEL ROD()
Specification : DIA 64MM+/-0.5MM STEEL ROD TO SPECIFICATION IS:7283 1992 WITH MATERIAL TO CHEMICAL & MECHANICAL PROPERTY REQUIRMENTS OF IS:226 1975 FE 410-5 OR BS 970 PT1 :1991 GRADE 070 M 20 NORMALISED
R
Estab
Category : s
Grade : 3
Size :
S
1Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) ST WIRE SPG 1 point 30 MM
Description : ST WIRE SPG 1 point 30 MM()
Specification : SPRING STEEL WIRE DIA. 1.30MM TO SPECN- IS:4454:PT-1:2001GD-DH WITH UTS VALUE MIN 2300N/MM2
R
Estab
Category : s
Grade : 3
Size :
S
1Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) STEEL RD 45MM DIA IN HOT ROLLED AND ANNELED CONDITION FOR MAG
Description : STEEL RD 45MM DIA IN HOT ROLLED AND ANNELED CONDITION FOR MAG()
Specification : SPECNIS:5517-1993 DESIG.42CR4MO2.TEST PIECE TO BE TESTED IN`V' CONDITION.MATL. SHOULD ALSO SATISFY MACRO ETCH & NMIR TEST AS ANNEXURE NATURE-C A SEPERATE T.P. IS TO BE QUENCHED & TEMPERED BEFORE MACHINING TO ACHIEVE HARDNESS 280-335HB.
R
Estab
Category : s
Grade : 3
Size :
S
1Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) STEEL ROUND 14 MM DIA
Description : STEEL ROUND 14 MM DIA()
1) STEEL RD 25MM DIA FOR MAG
Description : STEEL RD 25MM DIA FOR MAG()
Specification : SPECN.BS:970:PT-3:1991 GD.420S29 OR 431S29HARDENED & TEMPERED BARS TO HARDNESS 265-300 BHN.MACRO ETCH & NMIR TEST TO BE CARRIED OUT AS PER ANNEXURE NATURE `C'. (REQUIRED FOR GAS REGULATOR D S CAT NO. 1005-006614)
R
Estab
Category : p
Grade : 3
Size :
S
1Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) SIDE STOCK TRIGGER GRIP LEFT IN FINISHED CONDITION FOR MAG
Description : SIDE STOCK TRIGGER GRIP LEFT IN FINISHED CONDITION FOR MAG()
Specification : SIDE STOCK TRIGER GRIP LEFT IN FINISHED CONDITION TO DS CAT NO.1005-000602 DC (I) NO.25286 -SA DT:11 /03/2002
1) SPARE WHEEL CARRIER ASSY WITHOUT REDUCTION GEAR BOX[90]()
Specification : SPARE WHEEL CARRIER ASSY. W/O SPARE WHEEL CARRIER ASSY. PART NO. A0909100 WITHOUT REDUCTION GEAR BOX TO (PART NO. X3917700 CONSISTING OF 60 ITEM AS PER LIST ENCLOSED. N/A
C
Nonestab
2) STEERING PIPE RETURN LINE B2238210[90]()
Specification : STEERING PIPE RETURN LINE,BS3 STEERING PIPE RETURN LINE PART NO.B 2238210-B2,BS-III STALLI ON VEHICLE.
C
Nonestab
3) STEERING PIPE RETURN LINE B2238211[90]()
Specification : STEERING PIPE RETURN LINE BS3 STEERING PIPE RETURN LINE B2238211(B.1)BSIII STALLION VEH.
1) BUTTON SPECIAL OF GRIP LEFT ASSY FOR FIRING DEVICE IB[70]()
Specification : BUTTON SPECIAL AS PER DRG.NO.CQA (I)-393/18, CAT/PT.NO.5340-014217 OF GRIP LEFT ASSY FOR DEVICE FIRING IB
C
Nonestab
2) PIN STRAIGHT HEADED OF GRIP LEFT ASSY FOR FIRING DEVICE IB FOR MINE[70]()
Specification : PIN STRAIGHT HEADED AS PER DRG.NO. CQA (I)-393/19,CAT/PT.NO.5315-008702 OF GRIP LEFT ASSY FOR DEVICE FIRING IB FOR MINE
C
Nonestab
3) SCREW EXTERNALLY RELEIVED BODY FOR FIRING DEVICE[70]()
Specification : SCREW EXTERNALLY RELEIVED BODY AS PER DRG.NO.CQA(I) 393/16 FOR DEVICE FIRING 1B CAT./PT.NO.5305-016659
C
Nonestab
4) SCREW SPECIAL FOR FIRING DEVICE IB[70]()
Specification : SCREW SPECIAL AS PER DRG.NO.CQA (I)-393/6,CAT/PT.NO.5305 -016657 FOR DEVIE FIRING IB
C
Nonestab
5) SPRING LEAF OF GRIP ASSY FOR FIRING DEVICE IB[70]()
Specification : SPRING LEAF AS PER DRG.NO.CQA (I)-393/21, CAT./PT.NO.5340-014215 OF GRIP ASSY FOR DEVICE FIRING IB
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) BUTTON SPECIAL OF GRIP LEFT ASSY FOR FIRING DEVICE IB[70]()
Specification : BUTTON SPECIAL AS PER DRG.NO.CQA (I)-393/18, CAT/PT.NO.5340-014217 OF GRIP LEFT ASSY FOR DEVICE FIRING IB
C
Nonestab
2) SCREW SPECIAL FOR FIRING DEVICE IB[70]()
Specification : SCREW SPECIAL AS PER DRG.NO.CQA (I)-393/6,CAT/PT.NO.5305 -016657 FOR DEVIE FIRING IB
C
Nonestab
3) SCREW SPECIAL AS PER DRG NO CQA I 393 7 CAT PT NO 5305 016656 FOR FIRING DEVICE IB[70]()
Specification : SCREW SPECIAL AS PER DRG.NO.CQA(I)-393/7, CAT/PT NO.5305-016656 FOR DEVICE FIRING IB
C
Nonestab
4) SPRING LEAF OF GRIP ASSY FOR FIRING DEVICE IB[70]()
Specification : SPRING LEAF AS PER DRG.NO.CQA (I)-393/21, CAT./PT.NO.5340-014215 OF GRIP ASSY FOR DEVICE FIRING IB
C
Nonestab
5) Nut Castellated Hexagon[70]()
Specification : NUT CASTELLATED HEXAGON AS PER DRG.NO.CQA (I)-393/3,CAT./PT.NO.5310-021796 FOR DEVICE FIRING IB FOR MINE
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) SUPPLY OF GAS PORT BLOCK AS PER DRG. No.K-1205 WITH FIRM'S MATERIAL[70]()
Specification : AS PER DRG. No.K-1205 WITH FIRM'S MATERIAL
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) SUPPLY OF REAR SIGHT ELEVATING SLIDE AS PER DRG NO K 2025 WITH FIRMS MATERIAL[70]()
Specification : AS PER DRG. NO. K 2025
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) SUPPLY OF REAR SIGHT ELEVATING SLIDE CATCH AS PER DRG NO K 2023 WITH FIRMS MATERIAL[70]()
Specification : AS PER DRG NO. K 2023
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) SUPPLY OF FRONT SIGHT BLOCK AS PER DRG No K1207 WITH FIRMS MATERIAL[70]()
Specification : AS PER DRG. NO. K-1207 WITHFIRM'S MATERIAL
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) SUPPLY OF GAS PORT BLOCK AS PER DRG No K1205 WITH FIRMS MATERIAL[70]()
Specification : AS PER DRG. No.K-1205 WITH FIRM'S MATERIAL
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) SUPPLY OF GAS PORT BLOCK AS PER DRG No K1205 WITH FIRMS MATERIAL[70]()
Specification : AS PER DRG. No.K-1205 WITH FIRM'S MATERIAL
C
Nonestab
2) SUPPLY OF REAR SIGHT ELEVATING SLIDE CATCH AS PER DRG NO K 2023 WITH FIRMS MATERIAL[70]()
Specification : AS PER DRG NO. K 2023
C
Nonestab
3) SUPPLY OF GAS PISTON BLANK AS PER DRG NO TEND 2547 STAR 5 WITH FIRMS MATERIAL[70]()
Specification : AS PER DRG NO. TEND 2547 STAR 5 WITH FIRMS MATERIAL
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) SELECTOR LEVER AS PER DRGNOK 2074 WITH FIRMS MATERIAL[70]()
Specification : AS PER DRG.NO.K 2074 WITH FIRM'S MATERIAL
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) SUPPLY OF FRONT SIGHT BLOCK AS PER DRG No K1207 WITH FIRMS MATERIAL[70]()
Specification : AS PER DRG. NO. K-1207 WITHFIRM'S MATERIAL
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) SUPPLY OF FRONT SIGHT BLOCK AS PER DRG No K1207 WITH FIRMS MATERIAL[70]()
Specification : AS PER DRG. NO. K-1207 WITHFIRM'S MATERIAL
C
Nonestab
2) REAR SIGHT BLOCK BLANK S3 AS PER DRG NO TEND 2509STR FOR K1202STR[70]()
Specification : REAR SIGHT BLOCK BLANK S3 AS PER DRG NO TEND 2509STR FOR K1202STR
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) SUPPLY OF REAR SIGHT ELEVATING SLIDE AS PER DRG NO K 2025 WITH FIRMS MATERIAL[70]()
Specification : AS PER DRG. NO. K 2025
C
Nonestab
2) SUPPLY OF GAS PORT BLOCK AS PER DRG NO K 1205 STAR 3 WITH FIRMS MATERIAL[70]()
Specification : SUPPLY OF GAS PORT BLOCK AS PER DRG NO K 1205 STAR 3 WITH FIRMS MATERIAL
C
Nonestab
3) ROD HANDLE AS PER DRAWING 33P 2021 IN FULLY FINISHED WITH FIRMS MATERIAL[70]()
Specification : ROD HANDLE AS PER DRAWING 33P 2021 IN FULLY FINISHED WITH FIRMS MATERIAL
C
Nonestab
4) LAUNCHER SHAFT[70]()
Specification : LAUNCHER SHAFT TO DRG. NO. 30P 1105 EXPL FOR HOUSING LAUNCHER ASSY OF MGL WITH FIRM'S MATERIAL
C
Nonestab
5) Manufacturing and supply of Rear Cross blank DRG NUMBER TEND 2655[70]()
Specification : MANUFACTURING AND SUPPLY OF REAR CROSS BLANK DRAWING NO. TEND 2655 WITH FIRM'S MATERIAL REQUIRED FOR MSL
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Gun Carriage Factory
Name
Specification
Use
Status
1) PIN AXIS DEPRESSION LEVER TO PART NO BOF 6097384[90]()
Specification : PIN AXIS DEPRESSION LEVER TO PART NO BOF-6097384
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Gun Carriage Factory
Name
Specification
Use
Status
1) BUSH TO DRG NO 5060095 5060095 Y[90]()
Specification : BUSH TO DRG NO 5060095 5060095 Y
C
Nonestab
2) BUSH BOF 6164802[90]()
Specification : BUSH BOF 6164802
C
Nonestab
3) BUSH BOF 6104225 Y[90]()
Specification : BUSH BOF 6104225 Y
C
Nonestab
4) PIN TO DS CAT NO 5315 001004[90]()
Specification : PIN TO DS CAT NO 5315 001004
C
Nonestab
5) PIN AXIS DEPRESSION LEVER BOF 6097384[90]()
Specification : PIN AXIS DEPRESSION LEVER BOF 6097384
C
Nonestab
6) PLATE LOCKING PISTON JOINT PIN TO PART NO BOF 6108932[90]()
Specification : PLATE LOCKING PISTON JOINT PIN TO PART NO BOF 6108932
C
Nonestab
7) 9080081467 PIN SHOULDER HEADED TO DRG NO 5315 001003[90]()
Specification : PIN SHOULDER HEADED TO DRG NO 5315 001003
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) BODY COVER WITH INTEGRAL PICATINY RAIL FOR LMG BELT FED[70]()
Specification : BODY COVER WITH INTEGRAL PICATINY RAIL LMG 7.62MM BELT FED AS PER DRG. NO. ARDE/SK/108/005
C
Nonestab
2) PIN DISASSEMBLY FOR REVOLVER SIDE SWING[70]()
Specification : PIN DISASSEMBLY FOR REVOLVER 0.32 SIDE SWING DRG. NO. RV-06/4 SW.
C
Nonestab
3) PIN HAMMER DOG FOR REVOLVER SIDE SWING[70]()
Specification : PIN HAMMER DOG FOR REVOLVER 0.32 SIDE SWING DRG. NO. RV-05/5 SW.
C
Nonestab
4) WASHER EJECTOR ROD FOR REVOLVER SIDE SWING[70]()
Specification : WASHER EJECTOR ROD FOR REVOLVER 0.32 SIDE SWING DRG. NO. RV-04/7 SW.
C
Nonestab
5) Body Finished Through IC for Revolver Side Swing[70]()
Specification : Body Finished Through I.C./Machining Route for Revolver .32 Side Swing Drg. No. RV-03/1 SW.
R
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) PEGS NIGHT LINE MG MK I[70]()
Specification : PEGS NIGHT LINE MG MK-I TO DS CAT NO.1005-000755 DC (I) NO.24576-SA DT.01.11.99 IN FINISHED CONDITION.
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) BRACKET DRG NO-155/COMP-5/98.BASED ON DRG NO-6 358 138.[71]()
Specification : BRACKET DRG NO-155/COMP-5/98.BASED ON DRG NO-6 358 138. REQD FOR 155MMM FH GUN.
R
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) AXIS PIN AS PER DRG. NO.5174739[71]()
Specification : AXIS PIN AS PER DRG. NO.5174739 FOR 155 MM FH GUN.
R
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) PRE MACHINING ACTUATING AXLE SHAFT DRG.NO.4077843[71]()
Specification : PRE MACHINING ACTUATING AXLE SHAFT DRG.NO.4077843 MATERIAL BS:970 PT 1983 GRADE 835 M30 COMPONENT OF 155 FH BO
FORS.
R
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) FINISH MACHINING OF BOLT AS PER DRG NO.2A20-01-32.[72]()
Specification : FINISH MACHINING OF BOLT AS PER DRG NO.2A20-01-32.
R
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) F/M CAM CONTROL HANDLE[71]()
Specification : F/M CAM CONTROL HANDLE
S
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) EXTRACTOR AS PER DRG NO.4081489 155 MM FH GUN.[71]()
Specification : EXTRACTOR AS PER DRG NO.4081489 155 MM FH GUN.
R
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) FINISH COMPONENT OF LOCKING PLATE[76]()
Specification : FINISH COMPONENT OF LOCKING PLATE AS PER DRG.NO.161-1490 FOR SHARANG ORD
C
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) FINISH COMPONENT OF TOP SLIDE 176 1118[76]()
Specification : FINISH COMPONENT OF TOP SLIDE AS PER DRG.NO.176-1118 FOR SHARANG ORD.
C
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) CAP FOR SHARANG 161 473[76]()
Specification : CAP AS PER DRG NO-161-473 FOR SHARANG ORDNANCE
C
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) KEY AS PER DRG 161 480[76]()
Specification : KEY AS PER DRG.NO.161-480 FOR SHARANG ORD
C
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) PLUNGER AS PER DRG 161 463 FOR SHARANG[76]()
Specification : PLUNGER AS PER DRG 161-463 FOR SHARANG ORD
C
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) CAM CONTROL HANDLE[71]()
Specification : CAM CONTROL HANDLE
C
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) COLLAR SHAFT AS PER DRG No 3040 003628[41]()
Specification : COLLAR SHAFT AS PER DRG No 3040 003628
C
Estab
2) PACKING NUT AS PER DRG No 4730 006960[41]()
Specification : PACKING NUT AS PER DRG No 4730 006960
C
Estab
3) SCREW AS PER DRG No 5305 003184[41]()
Specification : SCREW AS PER DRG No 5305 003184
C
Estab
4) PLUG AS PER DRG No 1015 000547[41]()
Specification : PLUG AS PER DRG No 1015 000547
C
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) EXTRACTOR AS PER DRG NO.4081489 155 MM FH GUN.[71]()
Specification : EXTRACTOR AS PER DRG NO.4081489 155 MM FH GUN.
R
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) BRACKET DRG NO-155/COMP-5/98.BASED ON DRG NO-6 358 138.[71]()
Specification : BRACKET DRG NO-155/COMP-5/98.BASED ON DRG NO-6 358 138. REQD FOR 155MMM FH GUN.
R
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) AXIS PIN AS PER DRG. NO.5174739[71]()
Specification : AXIS PIN AS PER DRG. NO.5174739 FOR 155 MM FH GUN.
R
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) FINISH MACHINING OF BOLT AS PER DRG NO.2A20-01-32.[72]()
Specification : FINISH MACHINING OF BOLT AS PER DRG NO.2A20-01-32.
R
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) HAMMER TO DRG. NO. 32-0601 MK-III[70]()
Specification : HAMMER TO DRG. NO. 32-0601 MK-III,MATERIAL BS 970 PT I 1983 GD:070 M-55(B.S 970 EN-9) ALT.MATERIAL: FROM I.C ROUTE I.C DRG NO.SK-5377R BS 3146 Pt.1-1974. TYPE CLASS-12 Gr.A.
R
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) LOCKING PIECE FOR SHARANG ORD[76]()
Specification : LOCKING PIECE AS PER DRG.NO.166-217
C
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) FIXING PIN FOR SHARANG ORD[76]()
Specification : FIXING PIN AS PER DRG.NO.176-1212 FOR SHARANG ORD
C
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) FIXING PIN 1185[76]()
Specification : FIXING PIN AS PER DRG.NO.176-1185 FOR SHARANG ORD
C
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) ADOPTER 161[76]()
Specification : ADOPTER AS PER DRG.NO.161-1500 FOR SHARANG ORD
C
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) FINISH COMPONENT OF TOP SLIDE 176 1118[76]()
Specification : FINISH COMPONENT OF TOP SLIDE AS PER DRG.NO.176-1118 FOR SHARANG ORD.
C
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) CAP FOR SHARANG 161 473[76]()
Specification : CAP AS PER DRG NO-161-473 FOR SHARANG ORDNANCE
C
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) KEY AS PER DRG 161 480[76]()
Specification : KEY AS PER DRG.NO.161-480 FOR SHARANG ORD
C
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) FINISH COMPONENT OF KEY 176 1104 FOR SHARANG[76]()
Specification : FINISH COMPONENT OF KEY 176 1104 FOR SHARANG FOR SHARANG ORD
C
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) PLUNGER AS PER DRG 161 463 FOR SHARANG[76]()
Specification : PLUNGER AS PER DRG 161-463 FOR SHARANG ORD
C
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) CAM CONTROL HANDLE[71]()
Specification : CAM CONTROL HANDLE
C
Estab
Category :
Grade : Grade III
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) COLLAR SHAFT AS PER DRG No 3040 003628[41]()
Specification : COLLAR SHAFT AS PER DRG No 3040 003628
C
Estab
2) PACKING NUT AS PER DRG No 4730 006960[41]()
Specification : PACKING NUT AS PER DRG No 4730 006960
C
Estab
3) SCREW AS PER DRG No 5305 003184[41]()
Specification : SCREW AS PER DRG No 5305 003184
C
Estab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) OILER HAND NO1 MK1 MAG GUN[71]()
Specification : OILER HAND NO.1 MK1 FOR GUN M /C (MAG) 7.62MM 2A DS-CATNO.4930-000799 DC(I)NO.25144-SA DATED 11-10-2001
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) BLANK FOR BODY COVER FOR MAG 7 62MM[01]()
Specification : BLANK FOR BODY COVER DRG.NO.SKM-902*1 . MATERIAL- AL.FORG.TO DRG. SKM-174* TO BE SUPPLIED BY FACTORY FROM L.F.NO.0614279001 AGAINST B/G
C
Nonestab
2) FEED ARM FOR AIR VERSION for MAG[70]()
Specification : FEED ARM FOR AIR VERSION TO DRG NO. 3602008380 IN FINISHED CONDITION
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) Rod Rear Spring Recoil for JVPC[70]()
Specification : Rod Rear Spring Recoil for JVPC 5.56 DRG No. 0204 03 04 00 06 002 00DA
C
Nonestab
2) Barrel Extension Blank up to Stage V for JVPC[70]()
Specification : Barrel Extension Blank up to Stage 'V' to drg. No. SK-JVPC-1087* for JVPC 5.56 MM with SAF material (I/Code-7012470452)
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) BARREL COVER ASSEMBLY FOR JVPC[70]()
Specification : BARREL COVER ASSEMBLY FOR JVPC 5.56 X 30MMDRG. NO. 0204-03-03-01-12-000-00DA CONSISTING OFBARREL COVER MOULDING BUSH BARREL COVER,
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) BODY HOUSING UPPER WELDING FOR JVPC 5.56 X 30MM DRG NO. SK-5729*CONSISTING OF BODY HOUSING UPPER, CHANNEL LEFT, CHANNEL RIGHT, TUBE SPACER[70]()
Specification : BODY HOUSING UPPER WELDING FOR JVPC 5.56 X 30MM DRG NO. SK-5729*CONSISTING OF BODY HOUSING UPPER, CHANNEL LEFT, CHANNEL RIGHT, TUBE SPACER
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) BODY HOUSING LOWER and TRIGGER MECHANISM ASSEMBLY FOR JVPC[70]()
Specification : BODY HOUSING LOWER & TRIGGER MECHANISM ASSEMBLY FOR JVPC 5.5 6X30MM DRG NO. 0204-03-03-02-15-000-00DB
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) LEVER PIN LOCKING IN FINISHED CONDITION[70]()
Specification : LEVER PIN LOCKING TO DRG.NO. CQA(SA)SK- 588/1 DC(I) NO. 26933-SA DT- 07.09.16 IN FINISHED CONDITION. DS CAT NO 1005-560293.
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) LEVER CAM TO DRG No PH 1 3 IN FINISHED CONDITION FOR REVOLVER[70]()
Specification : LEVER CAM DRG PH-1-3 IN FINISHED CONDITION. D.A. NO. 35/04 DT. 09-04-04
1) BODY COVER WITH INTEGRAL PICATINY RAIL FOR LMG BELT FED[70]()
Specification : BODY COVER WITH INTEGRAL PICATINY RAIL LMG 7.62MM BELT FED AS PER DRG. NO. ARDE/SK/108/005
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) CATCH FEED COVER FOR MAG 7.62MM TO DS CAT NO. 1005-006627 DC(I) NO. 25321-SA DT- 08.04.2002 IN FINISHED CONDITION.(MAT. AGAINST L.F 0614230110 WILL BE SUPPLIED BY FACTORY AGAINST BANK GUARNTEE.[70]()
Specification : CATCH FEED COVER FOR MAG 7.62MM TO DS CAT NO. 1005-006627 DC(I) NO. 25321-SA DT- 08.04.2002 IN FINISHED CONDITION.(MAT. AGAINST L.F 0614230110 WILL BE SUPPLIED BY FACTORY AGAINST BANK GUARNTEE.
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) SCREW PLATE BODY IN FINISHED CONDITION REQUIRED FOR REVOLVER[70]()
Specification : SCREW PLATE BODY IN FINISHED CONDITION REQUIRED FOR REVOLVER MK-III DRG NO PHMK-III-1-19
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) COVER PLATE ACCESS TO DS CAT NO. 1005-006647 DC(I) NO. 25325-SA DT- 10.4.02 IN FINISHED CONDITION.[70]()
Specification : COVER PLATE ACCESS TO DS CAT NO. 1005-006647 DC(I) NO. 25325-SA DT- 10.4.02 IN FINISHED CONDITION.
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) PIN STRAIGHT HEADLESS RETAINING SLEEVE for MAG[70]()
1) STEEL BLANK FOR PISTON EXTENSION STAGE VI SIXTH TO DRG NO SK 5143[04]()
Specification : STEEL BLANK FOR PISTON EXTENSION STAGE VI(SIXTH) TO DRG NO-SK-5143*. NOTE:RAW MATERIAL WILL BE SUPPLIED BY SAF ON FREIGHT TO PAY BASIS AGAINST THE B/G THROUGH L/FOLIO NO.0412001042.
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) BUTTON CATCH MAGAZINE FOR JVPC[70]()
Specification : BUTTON CATCH MAGAZINE FOR JVPC 5.56MM DRG.NO.0204-03-02-02-19-002-00DD
C
Nonestab
2) Rod Front Spring Recoil for JVPC[70]()
Specification : Rod Front Spring Recoil for JVPC 5.56MM DRG. No. 204-03-02-00-06-003-00DD
C
Nonestab
3) Guide Piece Magazine for JVPC[70]()
Specification : Guide Piece Magazine for JVPC ,Drg. No. 0204-03-02-18-29-003-00DB
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) COVER for MAG[70]()
Specification : COVER TO DS CAT NO. 1005-000446 DC(I) NO. 25298-SA DT- 19.3.2002 IN FINISHED CONDITION.
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) SIGHT REAR FOR MAG[70]()
Specification : SIGHT REAR FOR MAG 7.62MM TO DRG. NO. DS CAT NO. 1005-006621 DC(I) NO. 25317-SA DT- 03.04.2002 IN FINISHED CONDITION.
1) CLOSING CUP DRG. NO. 0204-03-02-22-35-001-00DG[70]()
Specification : CLOSING CUP DRG. NO. 0204-03-02-22-35-001-00DG
C
Nonestab
2) BODY HOUSING UPPER WELDING FOR JVPC 5.56 X 30MM DRG NO. SK-5729*CONSISTING OF BODY HOUSING UPPER, CHANNEL LEFT, CHANNEL RIGHT, TUBE SPACER[70]()
Specification : BODY HOUSING UPPER WELDING FOR JVPC 5.56 X 30MM DRG NO. SK-5729*CONSISTING OF BODY HOUSING UPPER, CHANNEL LEFT, CHANNEL RIGHT, TUBE SPACER
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) BODY HOUSING BLANK[70]()
Specification : BODY HOUSING BLANK TO DRG NO. AKC-03/1M FOR CARBINE 5.56MM.
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) CLIP for MAG[70]()
Specification : CLIP TO DS CAT NO. 5340-007354 DC NO. 27021-SA DT- 28.01.17 IN FINISHED CONDITION.
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) Threaded Piston Extension for CQB DRG No 1901 01 01 00 03 002 00DC[70]()
1) BLADE FORE SIGHT DS CAT NO 1005-000895 IN FINISHED CONDITION SMG 9MM CARBINE 1A1.DC(I)26911-SA-DT.09-08-2016.[70]()
Specification : BLADE FORE SIGHT DS CAT NO 1005-000895 IN FINISHED CONDITION SMG 9MM CARBINE 1A1.DC(I)26911-SA-DT.09-08-2016.
C
Nonestab
Category : p
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) PIN RIVETTING DS CAT NO. 5315-002018 IN FINISHED CONDITION FOR PLATE GRIP ASSEMBLY FOR CARBINE 9 MM . D C NO.25065-SA, DT: 10/07/2001[70]()
Specification : PIN RIVETTING DS CAT NO. 5315-002018 IN FINISHED CONDITION FOR PLATE GRIP ASSEMBLY FOR CARBINE 9 MM . D C NO.25065-SA, DT: 10/07/2001
P
Nonestab
Category : p
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) Trigger guard DS CAT No. 1005-000606 in finished condition[70]()
Specification : AS PER DRG. DS CAT No. 1005-00060
C
Nonestab
Category : p
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) BACK SIGHT D S CAT NO-1005-000823 IN FINISHED CONDITION OF SMG 9MM CARBINE 1A1.DC(I)24314-SA-DT.06-04-1999.[70]()
Specification : BACK SIGHT D S CAT NO-1005-000823 IN FINISHED CONDITION OF SMG 9MM CARBINE 1A1.DC(I)24314-SA-DT.06-04-1999.
C
Nonestab
Category : p
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) SIGHT REAR FOR MAG 7.62MM TO DRG. NO. DS CAT NO. 1005-006621 DC(I) NO. 25317-SA DT- 03.04.2002 IN FINISHED CONDITION.[70]()
Specification : SIGHT REAR FOR MAG 7.62MM TO DRG. NO. DS CAT NO. 1005-006621 DC(I) NO. 25317-SA DT- 03.04.2002 IN FINISHED CONDITION.
C
Nonestab
Category : p
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) CATCH REAR SIGHT CURSOR FOR MAG 7.62 MM[70]()
Specification : AS PER DRAWING
C
Estab
2) Pin for Pin Safety in finished condition of Striker Mechanism[70]()
Specification : Pin for Pin Safety in finished condition as
per Drawing No NAD 7606/1A of Striker
Mechanism No 8 MK-1
C
Nonestab
Category : p
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) CATCH REAR SIGHT CURSOR FOR MAG 7.62 MM[70]()
Specification : AS PER DRAWING
C
Estab
2) Pin for Pin Safety in finished condition of Striker Mechanism[70]()
Specification : Pin for Pin Safety in finished condition as
per Drawing No NAD 7606/1A of Striker
Mechanism No 8 MK-1
C
Estab
3) CATCH FEED COVER FOR MAG 7.62MM TO DS CAT NO. 1005-006627 DC(I) NO. 25321-SA DT- 08.04.2002 IN FINISHED CONDITION.(MAT. AGAINST L.F 0614230110 WILL BE SUPPLIED BY FACTORY AGAINST BANK GUARNTEE.[70]()
Specification : CATCH FEED COVER FOR MAG 7.62MM TO DS CAT NO. 1005-006627 DC(I) NO. 25321-SA DT- 08.04.2002 IN FINISHED CONDITION.(MAT. AGAINST L.F 0614230110 WILL BE SUPPLIED BY FACTORY AGAINST BANK GUARNTEE.
C
Estab
4) FEED ARM FOR AIR VERSION for MAG[70]()
Specification : FEED ARM FOR AIR VERSION TO DRG NO. 3602008380 IN FINISHED CONDITION
C
Estab
5) FORE SIGHT 1005 007737 IN FINISHED CONDITION[70]()
Specification : FORE SIGHT TO DRG.NO. ARDE SK-3143/1, DS CAT NO. 1005-007737 IN FINISHED CONDITION. DC(I) NO. 26931-SA DT- 06.09.16
C
Estab
6) GUIDE, UPPER RIGHT TO DS CAT NO. 1005-006839 DC(I) NO. 25338-SA DT- 23.4.02 IN WITHOUT HEAT TREATMENT CONDITION.[70]()
Specification : GUIDE, UPPER RIGHT TO DS CAT NO. 1005-006839 DC(I) NO. 25338-SA DT- 23.4.02 IN WITHOUT HEAT TREATMENT CONDITION.
C
Estab
7) FRONT GUIDE RETURN SPRING TO DS CAT NO. 2540-002853 DC(I) NO. 25535-SA DT-30/09/2002 IN FINISHED CONDITION.[70]()
Specification : FRONT GUIDE RETURN SPRING TO DS CAT NO. 2540-002853 DC(I) NO. 25535-SA DT-30/09/2002 IN FINISHED CONDITION. (MATERIAL WILL BE SUPPLIED BY S.A.F ON FREIGHT TO PAY AGAINST B/G.
C
Estab
8) Housing Plunger to DS CAT NO 1005 007900[70]()
Specification : HOUSING PLUNGER TO DRG.NO. ARDE SK-2825/33 IN FINISHED CONDN DS.CAT.NO.1005-007900 DC(I) NO.26948-SA,DATED 26.09.16
C
Estab
9) HOUSING REAR SIGHT FOR CARBINE 5 56MM[01]()
Specification : HOUSING REAR SIGHT IC TO DRG NO. AKC-08/1/1 I.C.* FOR CARBINE 5.56MM.
C
Estab
10) Latch Special in finished condition[70]()
Specification : Latch Special in finished condition to CAT No. 5325-000862 Drg. No. CQA(I) 393/24
C
Estab
11) LEVER EXTRACTOR FOR REVOLVER[70]()
Specification : LEVER EXTRACTOR DRG.NO.PH-1-7 IN FINISHED CONDITION D.A. NO. 05/18 DT. 07-03-18.
C
Estab
12) LINK LOWER for MAG[70]()
Specification : LINK (LOWER) TO DS CAT NO. 1005-000469 DC(I) NO. 25303-SA DT- 23.01.02 IN FINISHED CONDITION WITHOUT HT & PLATING.
AS PER DRG
C
Estab
13) LINK (UPPER) TO DS CAT NO. 1005-000468 DC(I) NO. 25303-SA DT- 23.3.02 IN FINISHED CONDITION WITHOUT HT & PLATING.[70]()
Specification : LINK (UPPER) TO DS CAT NO. 1005-000468 DC(I) NO. 25303-SA DT- 23.3.02 IN FINISHED CONDITION WITHOUT HT & PLATING.
C
Estab
14) LINK CROSS PIECE (SHORT) PART NO. 2065E TO DS CAT NO. 1005-006821 DC(I) NO. 25328-SA DT- 13.04.02 IN FINISHED CONDITION.[70]()
Specification : LINK CROSS PIECE (SHORT) PART NO. 2065E TO DS CAT NO. 1005-006821 DC(I) NO. 25328-SA DT- 13.04.02 IN FINISHED CONDITION.
C
Estab
15) LOCATING FLANGE TRIGGER TO DS CAT NO. 1005-000623 DC(I) NO. 25310-SA DT-30.3.02 IN FINISHED CONDITION.[70]()
Specification : LOCATING FLANGE TRIGGER TO DS CAT NO. 1005-000623 DC(I) NO. 25310-SA DT-30.3.02 IN FINISHED CONDITION.
C
Estab
16) LOCK RETAINER IN FINISHED CONDITION[70]()
Specification : LOCK RETAINER IN FINISHED CONDN.AS PER DRG. NO.- ARDE/SK-2689/291.DS CAT NO.5340-015159. DC(I) NO-26518-SA DTD-6.07.10.
C
Estab
17) Lug Sling to DRG No.-ARDE/SK-3145/69, DS CAT No. 1005-008025 in finished condition[70]()
Specification : Lug Sling to DRG No.-ARDE/SK-3145/69, DS CAT No. 1005-008025 in finished condition
C
Estab
18) Machining of Cap back of 9 mm Carbine DS CAT No. 1005-000860[70]()
Specification : AS PER DRG.
C
Estab
19) MULTI TOOTH LOCK WASHER[70]()
Specification : MULTI-TOOTH LOCK WASHER TYPE -C,COUNTERSUNK NOMINAL SIZE 5.3AS PER IS:5371/1989 OR LATEST EDITION SPRING STEEL PHOSPHATED.
C
Estab
20) NUT LOCKING BARREL for MAG[70]()
Specification : NUT LOCKING BARREL"0" NO. SIZE IN FINISHED CONDITION. D.S.CAT NO 5310-002661 DC(I) NO. 25349-SA DT 30.04.02
C
Estab
21) PAWL FEED FRONT TO DS CAT NO.1005-006637 DC(I) NO. 25321-SA DT- 08.04.02[70]()
Specification : PAWL FEED FRONT TO DS CAT NO.1005-006637 DC(I) NO. 25321-SA DT- 08.04.02 (I.C.DRG.NO. SKM 740*2 AGAINST LF NO. 0145077022 WILL BE SUPPLIED BY SAF AGAINST B/G)
C
Estab
22) PAWL FEED CENTRAL FOR MAG 762 MM[70]()
Specification : PAWL FEED CENTRAL IN FINISHED COND. DS CAT NO. 1005-006639 DC(I) NO. 27019-SA DT. 28.01.2017 FOR MAG 7.62MM
C
Estab
23) PIN AUTO SEAR FOR JVPC[70]()
Specification : PIN AUTO SEAR FOR JVPC 5.56MM DRG.NO. 0204-03-02-02-18-017 00DB
C
Estab
24) Pin Barrel Locking Catch[70]()
Specification : As per Drawing
C
Estab
25) PIN EXTRACTOR D S CAT NO -5315-002012 IN FINISHED CONDITION OF SMG 9MM CARBINE 1A1.DC(I)26339-SA DT,21-05-2007.[70]()
Specification : PIN EXTRACTOR D S CAT NO -5315-002012 IN FINISHED CONDITION OF SMG 9MM CARBINE 1A1.DC(I)26339-SA DT,21-05-2007.
C
Estab
26) Pin fixing barrel DRG. No. PH-1-9[70]()
Specification : As per Drg.
C
Estab
27) PIN COCKING HANDLE IN FINISHED CONDITION TO DS CAT NO 5315 009175[70]()
Specification : PIN COCKING HANDLE IN FINISHED CONDITION TO DS CAT NO.5315-009175.DC(I) NO.26927-SA DT.02.09.16
C
Estab
28) Pin Groove Headed For Trigger & Safety Sear drg .no. ARDE SK-2689/132 for LMG/Rifle 5.56mm[70]()
Specification : AS PER DRG.
C
Estab
29) Pin Grooved Headed for Hammer DS CAT NO 5315 009190[70]()
Specification : Pin Grooved Headed for Hammer DS CAT NO 5315 009190
C
Estab
30) Pin grooved Headed for Hinge cover for Carbine 5 56[70]()
Specification : PIN GROOVED HEADED FOR HINGE COVER TO DRG. NO.ARDE/SK- 3143/29.DS CAT NO.5315-009188 DC(I) NO.26927-SA DT.02.09.16
C
Estab
31) PIN HAMMER FOR CARBINE 5 56MM IN FINISHED CONDITION[70]()
Specification : PIN HAMMER DRG NO AKC 01/16 FOR CARBINE 5.56MM IN FINISHED CONDITION
C
Estab
32) PIN HINGE CONNECTOR BUTT FOR CARBINE 5 56MMIN FINISHED CONDITION[70]()
Specification : PIN HINGE CONNECTOR BUTT DRG NO AKC 01/17 FOR CARBINE 5.56MMIN FINISHED CONDITION.
C
Estab
33) PIN RETAINING COCKING STUD TO DS CAT NO. 5315-004848 DC(I) N0. 25370-SA DT- 22/05/2002 IN FINISHED CONDITION.[70]()
Specification : PIN RETAINING COCKING STUD TO DS CAT NO. 5315-004848 DC(I) N0. 25370-SA DT- 22/05/2002 IN FINISHED CONDITION.
C
Estab
34) PIN RETAINING GAS CYLINDER for MAG[70]()
Specification : PIN RETAINING GAS CYLINDER TO DS CAT NO. 5315 - 001518 DC(I) NO. 27105-SA DT.20.06.17 IN FINISHED CONDITION.
C
Estab
35) PIN RETAINING GAS CYLINDER TO DS CAT NO. 5315 - 001518 DC(I) NO. 26138-SA DT- 02.02.06 IN FINISHED CONDITION.[70]()
Specification : PIN RETAINING GAS CYLINDER TO DS CAT NO. 5315 - 001518 DC(I) NO. 26138-SA DT- 02.02.06 IN FINISHED CONDITION.
C
Estab
36) PIN RETAINING HANDLE COCKING SLIDE for MAG[70]()
Specification : PIN RETAINING HANDLE COCKING SLIDE TO DS CAT NO. 5315-004849 DC(I) NO. 27105-SA DT- 20.06.17 IN FINISHED CONDITION.
C
Estab
37) PIN STRAIGHT HEADED OF GRIP LEFT ASSY FOR FIRING DEVICE IB FOR MINE[70]()
Specification : PIN STRAIGHT HEADED AS PER DRG.NO. CQA (I)-393/19,CAT/PT.NO.5315-008702 OF GRIP LEFT ASSY FOR DEVICE FIRING IB FOR MINE
C
Estab
38) PIN STRAIGHT HEADED CARTRIDGE GUIDE PAWL for MAG[70]()
Specification : PIN STRAIGHT HEADED CARTRIDGE GUIDE PAWL TO DS CAT NO. 5315-001514 DC(I) NO. 27020-SA DT-28.01.17 IN FINISHED CONDITION.
C
Estab
39) PIN STRAIGHT HEADLESS AXIS LOCKING LEVER for MAG[70]()
Specification : PIN STRAIGHT HEADLESS (AXIS LOCKING LEVER) TO DS CAT NO. 5315-001525 DC(I) NO.27012-SB DT- 14.1.17 IN FINISHED CONDITION.
C
Estab
40) PIN TRIGGER HAMMER AND SEAR SAFETY for JVPC[70]()
Specification : PIVOT FEED LEVER DS CAT NO.1005-000462 DC NO. 25298-SA DTD.19.3.02
C
Estab
42) PLATE RETAINER TO DS CAT NO.1005-000985 IN FINISHED CONDN. REQUIRED FOR 9MM MAGAZINE DC(I)NO 25698SA DT 16-03-2003[70]()
Specification : PLATE RETAINER TO DS CAT NO.1005-000985 IN FINISHED CONDN. REQUIRED FOR 9MM MAGAZINE DC(I)NO 25698SA DT 16-03-2003
C
Estab
43) PLUNGER CATCH FOR MAG[70]()
Specification : PLUNGER, CATCH TO DS CAT NO. 1005-000443 DC(I) NO. 25298-SA DT- 19.3.2002 IN FINISHED CONDITION.
C
Estab
44) PULL THROUGH 5.56MM1A (NYLON) TO DS CAT NO. 1005-557944 DC(I) NO. 26532-SA , DT. 30-07-10[71]()
Specification : PULL THROUGH 5.56MM1A (NYLON) TO DS CAT NO. 1005-557944 DC(I) NO. 26532-SA , DT. 30-07-10
C
Estab
45) Rear Feed Pawl FOR MAG[70]()
Specification : Rear Feed Pawl to DS CAT no. 1005-006638 DC(I) NO. 25321-SA, DT. 08-04-02 in finished condition
C
Estab
46) Rear Sight Cursor for MAG 7.62MM Drg No. 1005-000433[70]()
Specification : AS PER DRG. DS CAT 1005-000433 DC (I) 26752-SA DTD. 03.04.2015
C
Estab
47) REBOUND SLIDE TO DRG NO PHMK-III-1-22 IN FINISHED CONDITION REQUIRED FOR REVOVER MK-III[70]()
Specification : REBOUND SLIDE TO DRG NO PHMK-III-1-22 IN FINISHED CONDITION REQUIRED FOR REVOVER MK-III
C
Estab
48) RETAINER IN FINISHED CONDITION FOR AMOGH CARBINE 5 56[70]()
Specification : RETAINER TO DRG.NO.ARDE SK-2689/90 IN FINISHED CONDITION. DS CAT NO.1005-007824 DC(I)NO.26547-SA DT.24.11.2010
C
Estab
49) Ring for Pin Safety[70]()
Specification : Ring for Pin safety alternative design in finished condition for Striker Mechanism drawing No. NAD 7606/1A
R
Estab
50) RIVET SNAP HEAD FOR BLOCK REAR FOR CARBINE 5 56[70]()
Specification : RIVET SNAP HEAD FOR BLOCK REAR AS PER DRG. NO. SK- 3543L* PROTECTIVE FINISH:-PHOSPHATED TO SPECN.JSS 0465-01-1988. CLASS II OIL FINISH
C
Estab
51) ROLLER FOR MAG[70]()
Specification : DRG NO. 1005-000559 DC(I) NO. 25307-SA DT-26/03/2002 IN FINISHED CONDITION.AS PER DRG.
C
Estab
52) ROLLER GUIDE FEED SLIDE LOWER FOR MAG[70]()
Specification : DS CAT NO.3120-004657 IN FINISHED CONDITION DC NO. 25298-SA , DT.19-03-02 (MAT.ST.RD.10 MM DIA GD.535A99 WILL BE SUPPLIED BY SAF ON B/G FROM L.F.NO.0352001010
C
Estab
53) ROLLER GUIDE FEED SLIDE UPPER FOR MAG[70]()
Specification : DS CAT NO. 3120-004658, DC NO.27108-SA,DT.23-06-17 IN FINISHED CONDITION (MATL.ST ROD.10 MM DIA WILL BE SUPPLIED BY S.A.F.ON B/G FROM L.F.NO.0352001010AS PER DRG.AS PER DRG.
C
Estab
54) Screw Barrel Cover for JVPC[70]()
Specification : Screw Barrel Cover M5x20 for 5.56 MM as per IS: 1366
C
Estab
55) SIDE STOCK TRIGGER GRIP LEFT IN FINISHED CONDITION FOR MAG[70]()
Specification : SIDE STOCK TRIGER GRIP LEFT IN FINISHED CONDITION TO DS CAT NO.1005-000602 DC (I) NO.25286 -SA DT:11 /03/2002
C
Estab
56) SLEEVE BOLT COVER IN FINISHED CONDITION[70]()
Specification : SLEEVE BOLT COVER IN FINISHED CONDITION DS CAT NO.1005-006624 DC (I) NO.26159-SA,DT.09-02-06 (MATL.ST.ROD 1/2" DIA GD.605M36 FROM L.F NO.0283001013/02830 00012 WILL BE SUP.BY.SAF .ON B/G.
C
Estab
57) SEAR TRIPPER FOR MAG[70]()
Specification : DRG.DS CAT NO.1005-000620 DC (I) NO.27019-SA DT.28.1.17 IN FINISHED CONDITION.
C
Estab
58) SPLIT COLLAR GAS REGULATOR FOR MAG[70]()
Specification : SPLIT COLLAR, GAS REGULATOR TO DS CAT NO. 1005-000402 DC(I) NO. 25292-SA DT- 14.3.02 IN FINISHED CONDITION.
12) CLEANING TOOL SA NO.1 MK-1 FOR GUN M/C (MAG) 7.62MM 2A TO DS CAT NO.1005-000767 DC NO.20900-SA DT13-08-90 IN FINISHED CONDITION.[70]()
Specification : CLEANING TOOL SA NO.1 MK-1 FOR GUN M/C (MAG) 7.62MM 2A TO DS CAT NO.1005-000767 DC NO.20900-SA DT13-08-90 IN FINISHED CONDITION.
C
Estab
Category : p
Grade : Grade III
Size :
S
1Gun Carriage Factory
Name
Specification
Use
Status
1) PIN LOCKING CONNECTOR TO DRG. NO. BOF-6101832[90]()
Specification : PIN LOCKINGCONNECTOR TO DRG. NO. BOF-6101832
C
Nonestab
2) PIN LEFT TO DRG. NO. BOF-5047186[90]()
Specification : PIN LEFT TO DRG. NO. BOF-5047186
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Gun Carriage Factory
Name
Specification
Use
Status
1) PIN SHOULDER TO DRG. NO. 5315-001003[90]()
Specification : PIN SHOULDER TO DRG. NO. 5315-001003
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Gun Carriage Factory
Name
Specification
Use
Status
1) PIN TO DRG. NO. BOF - 6009603[90]()
Specification : PIN TO DRG. NO. BOF - 6009603
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Gun Carriage Factory
Name
Specification
Use
Status
1) PIN LEFT TO DRG. NO. BOF-5047186[90]()
Specification : PIN LEFT TO DRG. NO. BOF-5047186
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Gun Carriage Factory
Name
Specification
Use
Status
1) PIN SHOULDER TO DRG. NO. 5315-001003[90]()
Specification : PIN SHOULDER TO DRG. NO. 5315-001003
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Gun Carriage Factory
Name
Specification
Use
Status
1) PIN (L-7/247A) TO DRG. NO. BOF - 6127321[90]()
Specification : PIN (L-7/247A) TO DRG. NO. BOF - 6127321
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Gun Carriage Factory
Name
Specification
Use
Status
1) PLUNGERS HEAD LOCKING PIN TO PART NO 6112420[90]()
Specification : PLUNGERS HEAD LOCKING PIN TO PART NO 6112420
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Gun Carriage Factory
Name
Specification
Use
Status
1) 9081005312 LOCKING PIN D 12MM L 90MM PT 517149[90]()
Specification : LOCKING PIN D=12MM,L=90MM PART NO 5171493IN 5171492 WITH 4
ITEM AS LIST: A) Locking pin (KIPP PART NO K0366-25812090)
EQUIVALENT TO GCF PART NO 5171493 (QUANTITY:1).
B) KEY RING N5-12-20X2, 5(KIPP PART
C
Nonestab
2) 9081005313 LOCKING PIND 10M L 60MM PT 5171492[90]()
Specification : LOCKING PIN D=10MM,L=60MM PART NO 5171492 WITH 4 ITEMS AS
LIST: A) LOCKING PIN(KIPP PART NO K0366-25110060) EQUIVALENT
TO GCF PART NO 5171492(QUANTITY:1).
B) KEY RING N5-12-20X2,5(KIPP PART NO KO367.230
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) FRONT SIGHT BLOCK BLANK S3 L F No 7024012072[70]()
Specification : AS ER DRG No.TEND 2508 (for K 1207)
R
Nonestab
2) SUPPLY OF STAY HAMMER TO DRG No TEND 2016 WITH FIRMS MATERIAL ICR1333[70]()
Specification : AS PER DRG. No. TEND 2016 WITH FIRM'S MATERIAL.(ICR-1333)
C
Nonestab
3) PREMACHINED BLANK AS PER DRG NO TEND 2616 STAR 3 FOR TAR TRUNNION[70]()
Specification : PREMACHINED BLANK AS PER DRG NO TEND 2616 STAR 3 FOR TAR TRUNNION
C
Nonestab
4) PRE MACHINED BLANK TO DRAWING TEND 2639 STAR 2 CYLINDER FOR 38MM MSL WITH FIRMS MATERIAL[70]()
Specification : PRE MACHINED BLANK TO DRAWING TEND 2639*2 REQUIRED FOR 33P 2011 CYLINDER FOR 38MM MSL WITH FIRM'S MATERIAL
C
Nonestab
5) PRE MACHINED BLANK DRAWING TO TEND 2637 CYLINDER FOR 40MM MGL WITH FIRMS MATERIAL[70]()
Specification : PRE MACHINED BLANK DRAWING TO TEND 2637 CYLINDER FOR 40MM MGL WITH FIRM'S MATERIAL
C
Nonestab
6) PIN LOCKING PIN FIRING AND EXTRACTOR COMPONENT DRG NO 6P11 3 17 DRG NO 62 C 3017 200 D3[70]()
Specification : AS PER DRAWING OF PIN LOCKING PIN FIRING AND EXTRACTOR COMPONENT DRG NO 6P11 3 17 DRG NO 62 C 3017 200 D3
R
Nonestab
7) SUPPLY OF HINGE PIN AS PER DRG No K 4015 WITH FIRMS MATERIAL REQUIRED FOR TAR[70]()
Specification : SUPPLY OF HINGE PIN AS PER DRG No K-4015 WITH FIRM'S MATERIAL REQUIRED FOR TAR
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) SUPPLY OF TRIGGER AS PER DRG NO K2064 STAR 4 WITH FIRMS MATERIAL[70]()
Specification : SUPPLY OF TRIGGER AS PER DRG NO K2064 STAR 4 WITH FIRMS MATERIAL
Specification : AS PER DRG. No.29P 0004* required for 0.315" Sporting Rifle
C
Nonestab
3) TRIGGER TO DRG NO 29P 0040STAR required for 0POINT315 Sporting Rifle[70]()
Specification : AS PER DRG.NO.: 29P 0040* required for 0.315" Sporting Rifle
C
Nonestab
4) PIN STOP BOLT LOCKING TO DR NO 29P 0048STAR required for 0POINT315 Sporting Rifle[70]()
Specification : DRG.NO.: 29P 0048* required for 0.315" Sporting Rifle
C
Nonestab
5) SCREW PLATE BUTT TO DRG NO 29P 0059STAR required for 0POINT315 Sporting Rifle[70]()
Specification : AS PER DRG.NO. 29P 0059* required for 0.315" Sporting Rifle
C
Nonestab
6) SWIVEL SLING REAR TO DRG NO 29P 0065STAR required for 0POINT315 Sporting Rifle[70]()
Specification : AS PER DRG.NO.: 29P 0065* required for 0.315" Sporting Rifle
C
Nonestab
7) SUPPLY OF AUTO SEAR AS DRG NO K 2067 STAR 5 WITH FIRMS MATERIAL[70]()
Specification : SUPPLY OF AUTO SEAR AS DRG NO K 2067 STAR 5 WITH FIRMS MATERIAL
C
Nonestab
8) MSL HOUSING LAUNCHER[70]()
Specification : MANUFACTURE AND SUPPLY OF INPUT BLANK AS PER DRG. NO. TEND 2661 FOR MSL HOUSING LAUNCHER (BEFORE HARD ANODIZING STAGE) WITH FIRM'S MATERIAL
C
Nonestab
9) SUPPLY OF HINGE PIN AS PER DRG No K 4015 WITH FIRMS MATERIAL REQUIRED FOR TAR[70]()
Specification : SUPPLY OF HINGE PIN AS PER DRG No K-4015 WITH FIRM'S MATERIAL REQUIRED FOR TAR
C
Nonestab
10) SUPPLY OF PIN FIXING TRUNNION AS PER DRG No K 4008 WITH FIRMS MATERIAL REQUIRED FOR TAR[70]()
Specification : AS PER DRG No K_4008 WITH FIRMS MATERIAL REQUIRED FOR TAR
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) BUTTON FEED BOX A3-134 MAG7.62MM[70]()
Specification : AS PER DRG.
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) Holdall SA 1A 1005 000005[70]()
Specification : Holdall SA 1A DS CAT No. 1005-000005
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) Fore Sight Housing[70]()
Specification : Fore Sight Housing to DS CAT No. 1005-000426 in without Heat Treatment Condition
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) BLANK OF BLOCK GAS For JVPC[70]()
Specification : BLANK OF BLOCK GAS For JVPC
P
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) PIN REAR MOUNTING for MAG[70]()
Specification : PIN REAR MOUNTING 7.62MM MG MK-I DS CAT NO.5315-001554 IN FINISHED CONDITION DC(I) NO 21743-SA DT.21.5.92.
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) Mounting Rail for CQB 5 56x45 MM for CQB DRG No 1901 01 01 08 15 001 00DA[70]()
Specification : Mounting Rail for CQB 5 56x45 MM for CQB DRG No 1901 01 01 08 15 001 00DA
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) MAGAZINE LATCH AS PER DRAWING NO SK 6520 TE[70]()
Specification : MAGAZINE LATCH AS PER DRAWING NO SK 6520 TE
C
Nonestab
2) SCREW AS PER DRAWING NO SK 6506 TE[70]()
Specification : SCREW AS PER DRAWING NO SK 6506 TE
C
Nonestab
3) LATCH AS PER DRAWING NO SK 6519 TE[70]()
Specification : LATCH AS PER DRAWING NO SK 6519 TE
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Khamaria
Name
Specification
Use
Status
1) BOOSTER CUP & PIN FOR 84MM HEAT-551[99]()
Specification : SET OF BOOSTER CUP AND PIN FOR 84MM HEAT-551 AMMN. (BOOSTER CUP TO DRG NO.TRD-2-2-2277 & PIN TO DRG NO.TRD-1-2-2278 ).
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Khamaria
Name
Specification
Use
Status
1) LOCK WASHER JZE-2.55 (HEAT-551)[99]()
Specification : LOCK WASHER JZE-2.55 TO DRG.NO.TRD-1-2-2269.
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Khamaria
Name
Specification
Use
Status
1) TRACER BODY DRG NO.F1334-154780-D[99]()
Specification : TRACER BODY TO DRG NO.F-1334-154780-D, DC-36534-A DT.6/3/99
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Khamaria
Name
Specification
Use
Status
1) RIVET 2X10 TO DRG NO TRD 1 2 2239 LF 9911357870[99]()
Specification : RIVET 2x10 TO DRG.NO.TRD-1-2-2239.
C
Nonestab
2) SLIDING DISC PART NO 6413413 LF 9911358440[99]()
Specification : SLIDING DISC PART NO.6413413 TO OEM DRG.NO.304052464/ TRD.DRG.NO.1.2.2627
R
Nonestab
3) WASHER AS PER DRG NO MKTA 754152 003 LF 9911358670[99]()
Specification : WASHER AS PER DRG NO MKTA 754152 003 TRD 1 1 3223
C
Nonestab
4) WASHER AS PER DRG NO TRD 1 1 3223 LF 9911358675[99]()
Specification : WASHER AS PER DRG MKTA 754152 003 TRD 1 1 3223 ALT
C
Nonestab
5) SHELL HEI EMPTY 30MM BMP II LF 9911358129[99]()
Specification : BODY EMPTY WITH BAND ASSY TO DRG NO.bw5.500.009Cb/c 2 SHEETSSHEET-1 DC-37321-A DT 18-10-12 SHEET-2 DC- 34241-ADT.24/09/87 SPECN.PROGRAMME AND METHOD OF TESTING AS PERSHEET NO.5w5.500.112 M/C (5 SHEET) DC-34241-A DT.24-9-87.
C
Nonestab
6) DELAY TUBE EMPTY FOR DET 36M 7SEC LF 9911358772[99]()
Specification : DELAY TUBE (EMPTY) TO DRG.IQX 922 DC 36852-A DT.23/09/2002 FOR DETONATOR 36M 7 SEC
C
Nonestab
7) PRIMER BODY DRG NO IQX861 DC36304 A LF 9911358817[99]()
Specification : 81 MM PRIMER BODY TO DRG NO. IQX 861DC NO 36304-A DT. 03/07/97, SPECIFICATION OF MATERIAL, PROTECTIVE FINISH AND OTHER GENERAL REQUIREMENT TO THE
COMPONENT AS PER SPECIFICATION MENTIONED IN DRG NO. IQX861DC NO 36304-A DT. 03/07/97 & 04/
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) BAND RETAINER TO DS CAT NO 5340 015713[70]()
Specification : BAND RETAINER TO DS CAT NO. 5340-015713 D.C.NO. 26928-SA DT. 02.09.16 IN FINISHED CONDITION.
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) LATCH AS PER DRAWING NO SK 6519 TE[70]()
Specification : LATCH AS PER DRAWING NO SK 6519 TE
C
Nonestab
2) SIGHT LEAF DRG No SK 6540 TE[70]()
Specification : SIGHT LEAF DRG No SK-6540/TE
C
Nonestab
3) LATCH DRG No SK 6535 TE[70]()
Specification : LATCH DRG No SK- 6535 /TE
C
Nonestab
4) RETAINER Drg No SK 6526 TE[70]()
Specification : RETAINER Drg. No. SK-6526/TE
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) ROD CLEANING FOR MAG[71]()
Specification : ROD CLEANING 7.62MM BARREL GAS CYLINDER 1ATO DS CAT NO.1005-000358 DC (I) NO.23088-SA DT.19-9-95IN FINISHED CONDITION.,
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) ROD CLEANING SMALL ARMS[70]()
Specification : ROD CLEANING SMALL ARMS TO DRG. NO. CQA(SA)SK-464, DS CAT NO . 1005-560440 CONSISTING OF EIGHT COMPONENTS. DC(I) NO. 2636 4-SA,DT. 01-08-07.
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) MAGAZINE LATCH AS PER DRAWING NO SK 6520 TE[70]()
Specification : MAGAZINE LATCH AS PER DRAWING NO SK 6520 TE
C
Nonestab
2) SCREW AS PER DRAWING NO SK 6506 TE[70]()
Specification : SCREW AS PER DRAWING NO SK 6506 TE
C
Nonestab
3) SLIDE DRG No SK 6534 TE[70]()
Specification : SLIDE DRG No SK-6534/TE
C
Nonestab
4) LATCH DRG No SK 6535 TE[70]()
Specification : LATCH DRG No SK- 6535 /TE
C
Nonestab
5) PIN DRG No SK 6531 TE[70]()
Specification : PIN DRG No SK- 6531/ TE
C
Nonestab
6) Cleaning Rod Drg No SK 6574 TE[70]()
Specification : Cleaning Rod Drg No. SK- 6574/ TE
C
Nonestab
7) RIVET SK 6529 TE[70]()
Specification : RIVET SK- 6529/ TE
C
Nonestab
8) RAIL SK 6548 TE[70]()
Specification : RAIL SK-6548/ TE
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) MFG & SUPPLY OF LEVER LOCKING PIN TO DRG.NO 32P 4713 (M) WITH FIRM'S MATERIAL FOR UBGL[70]()
Specification : AS PER DRAWING
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) SCREW SEAR TO DRG NO 29P 0058 required for 0POINT315 Sporting Rifle[70]()
Specification : AS PER DRG. NO 29P 0058 required for 0.315" Sporting Rifle
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) PREMACHINED BLANK STAGE 2 FOR K 1205 AS PER DRG NO TEND2450 WITH FIRMS MATERIAL[70]()
Specification : AS PER DRG NO.TEND2450 WITH FIRM'S MATERIAL
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) SUPPLY OF HAMMER AS PER DRG NO K 2061 STAR2 WITH FIRMS MATERIAL[70]()
Specification : SUPPLY OF HAMMER AS PER DRG NO K 2061 STAR2 WITH FIRMS MATERIAL
C
Estab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) SEMI FINISHED BLANK PIN LEVER TRIGGER AND PIN FIRING FOR 40MM UBGL TO DRG NO. TEND 2193 WITH FIRM'MATERIAL[70]()
Specification : AS PER DRAWING
C
Nonestab
2) SEMI FINISHED BLANK PIN CATCH FOR 40MM UBGL TO DRG NO. TEND 2191 WITH FIRM'S MATERIAL[70]()
Specification : AS PER DRAWING
C
Nonestab
3) SEMI FINISHED BLANK PIN EXTRACTOR FOR 40MM UBGL TO DRG.NO. TEND 2192 WITH FIRM'S MATERIAL[70]()
Specification : AS PER DRAWING
C
Nonestab
4) SEMI FINISHED BLANK PIN FOR EJECTOR & SEAR FOR 40MM UBGL TO DRG NO. TEND 2190 WITH FIRM'S MATERIAL[70]()
Specification : AS PER DRAWING
C
Nonestab
5) PIN COCKING ARM TO DRG NO. 32P 4103*2 (FULLY FINISHED) WITH FIRM'S MATERIAL FOR 40MM UBGL[70]()
Specification : AS PER DRAWING
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) FRONT FEED PAWL for MAG
Description : FRONT FEED PAWL for MAG()
Specification : FRONT FEED PAWL DS CAT NO 1005-006637 IN FINISHED CONDTION WITH FIRM MATERIAL FOR MAG 7.62MM DC(I) NO. 25321-SA, DT. 08-04-02
C
Estab
2) PIVOT COVER SLIDE GUIDE ROLLER FOR MAG
Description : PIVOT COVER SLIDE GUIDE ROLLER FOR MAG()
12) PAWL FEED CENTRAL IN FINISHED COND. DS CAT NO. 1005-006639 DC(I) NO. 25325-SA DT. 10.04.2002 FOR MAG 7.62MM
Description : PAWL FEED CENTRAL IN FINISHED COND. DS CAT NO. 1005-006639 DC(I) NO. 25325-SA DT. 10.04.2002 FOR MAG 7.62MM()
Specification : PAWL FEED CENTRAL IN FINISHED COND. DS CAT NO. 1005-006639 DC(I) NO. 25325-SA DT. 10.04.2002 FOR MAG 7.62MM
C
Estab
13) Cleaning Tool SA No.-2 MK-1 to DS CAT No. 1005-000768
Description : Cleaning Tool SA No.-2 MK-1 to DS CAT No. 1005-000768()
Specification : Cleaning Tool SA No.-2 MK-1 to DS CAT No. 1005-000768
C
Estab
Category : p
Grade : 3
Size :
S
1Ordnance Factory Ambajhari
Name
Specification
Use
Status
1) ROLL PIN TO OFAJ DRG NO FS 3022 WITHOUT HEAT TREATMENT AND SURFACE TREATMENT[00]()
Specification : ROLL PIN TO OFAJ DRG NO FS 3022 WITHOUT HEAT TREATMENT AND SURFACE TREATMENT
C
Nonestab
Category : p
Grade : Grade III
Size :
S
1Ordnance Factory Dumdum
Name
Specification
Use
Status
1) FIN ASSY DET NO 1 SHT 7 TO DRG NO ARDE 2121 IN SEMI FINISHED CONDITION UPTO TACK WELDING[62]()
Specification : FIN ASSY.DET NO-1 SHT-7 TO DRG.NO.ARDE-2121 IN SEMI-FINISHED CONDITION UPTO TACK WELDING
C
Nonestab
2) STEEL CONTAINER FOR TU 1111 mod[14]()
Specification : STEEL CONTAINER (FOR TAIL UNIT NO.1111) TO DRG.NO.ARM 1519 IN FINISHED CONDITION
C
Nonestab
3) STEEL BOX FOR RTU 1121[62]()
Specification : BOX STEEL NO.-- MK-- TO DRG.NO.ARDE-2039 IN FINISHED CONDIT ION FOR 01 RTU TAIL UNIT NO. 1121, HOUSING BLOCK & CLEVIS UNIT ASSY. FOR 1000 LB MK 6 / MK 9 BOMB
C
Nonestab
4) FIN ASSY WELDING FOR TU 250[62]()
Specification : FIN ASSY. (WELDING) DET. NO.-13,SHT.NO.-1 TO DRG.NO.:ARDE 9501-03 IN FINISHED CONDITION (4 TO A SET).
C
Nonestab
5) FIN ASSY TO DRG NO ARDE 2139 DET NO 14 WITHOUT PROTECTIVE FINISH FOR TU 1111[62]()
Specification : FIN ASSY.TO DRG. NO. ARDE 2139, DET. NO. 14 WITHOUT PROTECTIVE FINISH
C
Nonestab
6) BOX STEEL NO 1 MK 1 TO HOLD 1 TAIL UNIT NO TB 250 OR TAIL UNIT TB 250 MOD 1 IN FINISHED CONDITION[14]()
Specification : BOX STEEL NO.1,MK-1 TO HOLD 1 TAIL UNIT NO.TB-250 OR TAIL UNIT TB 250-MOD-1 TO DRG.NO.[ARDE 9501-05 SHT.1/3 & SHT.2/3 WITH DC "ISSUE A" DT-10-03- 05 & SHT.3/3 WITH DC AL. NO.07/2008.DT.31-01-08.IN FINISHED CONDITION
C
Nonestab
7) COMPLETE BOX STEEL FOR TR 250[62]()
Specification : COMPLETE BOX STEEL NO.1 MK-1 TO HOLD 1 TAIL UNIT NO.TR 250 TO DRG.NO.ARDE 9501-04 SHT.1 & SHT.2 IN FINISHED CONDITION
C
Nonestab
8) BOX STEEL IN FC FOR RTU 2231[62]()
Specification : BOX STEEL NO. 1 TO DRG.NO.ARDE-2283 TO HOLD 01 HOUSING BLOCK & CLEVIS UNIT ASSY. & 01 TAIL UNIT No. 2231 WITH PARACHUTE FOR BOM 450 KG HSLD
C
Nonestab
9) STEEL SHEET FOR AERIAL BOMB[01]()
Specification : STEEL SHEET TO SIZE 3000 MM LONG X 1250 MM WIDTH X 2.24 MM T HICK (TOLERANCE +0.1 MM, -0.0 MM IN THICKNESS) TO SPECN IS : 5986 - 2002, GRADE : FE - 410
1) 6043000210 BOMB BODY 81MM MOR C EMP ITV 9A[60]()
Specification : CQA(A) 2305(M)
C
Nonestab
Category : p
Grade : Grade III
Size :
S
1Grey Iron Foundry
Name
Specification
Use
Status
1) SUSPENSION LUG. SUSPENSION LUG, AS PER DRG. NO. AQAW(A)/SK/MISC/14/1[62]()
Specification : SUSPENSION LUG.
SUSPENSION LUG, AS PER DRG. NO. AQAW(A)/SK/MISC/14/1
C
Nonestab
Category : dp
Grade : Grade I
Size :
S
1Grey Iron Foundry
Name
Specification
Use
Status
1) FINISHED FORGED HEAD COMPONENT OF 100/120 KGS. AERIAL BOMB[42]()
Specification : FINISHED FORGED HEAD COMPONENT OF 100/120 KGS. AERIAL BOMB
FINISHED FORGED HEAD COMPONENT OF 100/120 KGS. AERIAL BOMB
AS PER TERMS & CONDITIONS OF ANNEXURE 'A' ATTACHED
C
Nonestab
Category : dp
Grade : Grade I
Size :
S
1Grey Iron Foundry
Name
Specification
Use
Status
1) FORGED HEAD (UN-MACHINED) FOR 100-120 KG. AERIAL BOMB AS PER GIF DRAWING NO. 5310-A/FORGE AND TERMS & CONDITIONS ENCLOSED[66]()
Specification : FORGED HEAD (UN-MACHINED) FOR 100-120 KG. AERIAL BOMB
AS PER GIF DRAWING NO. 5310-A/FORGE
Specification : FILLING PLUG FORGING TO DRG. NO. OFM/32788.
C
Nonestab
7) FORGING FOR LUG 318 (6220601406)[62]()
Specification : FORGING FOR LUG SUSPENSION NO.318 AS PER DRG.OFM-31738A TO
BE SUPPLIED DULY HEAT-TREATED (HARDENED & TEMPERED) TO
ACHIEVE HARDNESS OF 180-250 VPN,Y.S. 44KG/SQR MM MIN.,UTS -
60-75 KG/SQR MM,ELONGATION-18% MIN.0N 5.65 UNDER ROOT "
C
Nonestab
8) Nose Plug 1000LBS(6220901044)[62]()
Specification : NOSE PLUG [MCD] TO DRG. NO. ARM - 1049B. [W/O SURFACE
TREATED]. [DRG. ENCLOSED.
C
Nonestab
9) Nose Plug 250KG (6240900504)[62]()
Specification : NOSE PLUG TO DRG. No. ARDE 9501-01 DET 14 (W/O PHOSPHATED).
DRG. ENCLOSED
C
Nonestab
10) ROLLING RING ASSEMBLY 450KG (6231100104)[62]()
Specification : ROLLING RING ASSEMBLY FOR 450 Kg HSLD BOMB AS PER Drg.No.-
ARDE-2122 DET.17 (WITHOUT PHOSPHATED) Drg.ENCLOSED,
C
Nonestab
11) FORGING FOR LUG -243 (6220700172)[62]()
Specification : FORGING FOR LUG 243,DRG. No,OFM-32616ATO BE SUPPLIED DULY
HEATTREATE D(HARDENED & TEMPERED)TO ACHIEVE HARDNESS OF
210-261 VPN.YS=46 KG/MM.SQ.MIN,UTS=70-85KG/MM.SQ,EL=5.
65 ROOT A-16% MIN.OR ON YFOUR ROOT A-20% MIN.
C
Nonestab
12) NOSE PLUG 450KG (6230900504)[62]()
Specification : NOSE PLUG [MCD] TO DRG. NO. ARDE 2122 DET NO. 7
[DRG. ENCLOSED]. [W/O SURFACE TREATED.
C
Nonestab
13) TA LINK FORGING[61]()
Specification : AS PER SPECIFICATION
C
Nonestab
14) SET OF TA SHOE AND TA GUIDE FORGING[61]()
Specification : AS PER SPECIFICATION
C
Nonestab
15) TA CLAMP FORGING[61]()
Specification : AS PER SPECIFICATION
C
Nonestab
16) TA LINK MACHINED FOLLOWED BY FORGING[61]()
Specification : AS PER OFM SPECIFICATION
C
Nonestab
17) SET OF TA SHOE AND TA GUIDE MACHINED FOLLOWED BY FORGING[99]()
Specification : AS PER SPECIFICATION
C
Nonestab
18) TA CLAMP MACHINED FOLLOWED BY FORGING[99]()
Specification : AS PER SPECIFICATION
C
Nonestab
19) TA WASHER T-90 (6120100106)[61]()
Specification : TA WASHER TO DRG.NO.OFM-32839.
C
Nonestab
20) TA PIN BLANK T-90 (6120100118)[61]()
Specification : T.A. PIN BLANK TO DRG. NO. OFM-32951 AS PER SPECIFICATION NO
OFM/TDS/TECH/O6A.
Specification : DRG. NO. OFBA/MPC/75. ALL THE ACCEPTANCE AND INSPECTION/QUALITY CRITERIA SHOULD BE AS PER TU 34E-2015
R
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Nalanda
Name
Specification
Use
Status
1) WOODEN CRATE[65]()
Specification : OFN/BMCS/M-92/WOODEN CRATE
C
Nonestab
Category : p
Grade : Grade II
Size :
S
1Ordnance Factory Nalanda
Name
Specification
Use
Status
1) WOODEN CRATE[65]()
Specification : OFN/BMCS/M-92/WOODEN CRATE
C
Nonestab
Category : p
Grade : Grade III
Size :
S
1Ordnance Factory Bolangir
Name
Specification
Use
Status
1) MOP.12 SHELLS 155MM B/T ON PELLET WITHOUT GRUMET[62]()
Specification : MOP.12 SHELLS 155MM B/T ON PELLET WITHOUT GRUMET TO DRG.NO:155-1000(M)(UNIT LOAD) CONSISTING OF PALLET TO DRG.NO.155-1210(M), FRAME ASSEMBLY TO DRG.NO.155- 1230(M) DCNO.37126-A,DT.25.7.07.
C
Nonestab
2) BOX UNIT LOAD FOR 155MM SHELL M107[14]()
Specification : BOX UNIT LOAD FOR 155MM SHELL M107 TO DRG.NO. 3058086, WITH LATEST DC(I) 36820-A, DT.16.03.2002
C
Nonestab
3) AMMN.CONTAINER BOX M 41A (WOOD) AND PACKING FITMENTS[14]()
Specification : AMMN.CONTAINER BOX M 41A (WOOD) AND PACKING FITMENTS TO DRG.PT.NO.ISV 587 A, DC.37127-A DT.30.07.07.
1) Fabrication of Jacket Combat PC Disruptive Pattern with Indian Army Logo (modified).[21]()
Specification : FABRICATION OF JACKET COMBAT PC DISRUPTIVE WITH INDIAN ARMY LOGO (MODIFIED).
SWO PART II No.60234
SPECIFICATION No : OCFAV/Garment/001(b)
MAKE & SHAPE : AS PER APPROVED SAMPLE
NOTE:
A) CUT COMPONENTS & GARNITURE WILL BE SUPPLI
E
Nonestab
2) Fabrication of Trousers Combat PC Disruptive Pattern with Indian Army Logo (modified).[21]()
Specification : FABRICATION OF TROUSER COMBAT PC DISRUPTIVE WITH INDIAN ARMY LOGO (MODIFIED).
SWO Pt II No.60233
SPECIFICATION No. OCFAV/Garment/002(b)
MAKE & SHAPE : AS PER APPROVED SAMPLE
NOTE:
A) CUT COMPONENTS & GARNITURE WILL BE SUPP
E
Nonestab
Category : p
Grade : Grade II
Size :
S
2429
KKR ENTERPRISES
NO:50,2 AND 3 FLOOR,VARADHARAJAPURAM KUMARASWAMY STREET,AMBATTUR CHENNAI Tamil Nadu
PIN1 : 600053
Phone No. : 48638588 GSTIN :
33AARFK8964G1ZR
1) Fabrication of Jacket Combat PC Disruptive Pattern with Indian Army Logo (modified).[21]()
Specification : FABRICATION OF JACKET COMBAT PC DISRUPTIVE WITH INDIAN ARMY LOGO (MODIFIED).
SWO PART II No.60234
SPECIFICATION No : OCFAV/Garment/001(b)
MAKE & SHAPE : AS PER APPROVED SAMPLE
NOTE:
A) CUT COMPONENTS & GARNITURE WILL BE SUPPLIE
E
Nonestab
2) Fabrication of Trousers Combat PC Disruptive Pattern with Indian Army Logo (modified).[21]()
Specification : FABRICATION OF TROUSER COMBAT PC DISRUPTIVE WITH INDIAN ARMY LOGO (MODIFIED).
SWO Pt II No.60233
SPECIFICATION No. OCFAV/Garment/002(b)
MAKE & SHAPE : AS PER APPROVED SAMPLE
NOTE:
A) CUT COMPONENTS & GARNITURE WILL BE SUPPL
E
Nonestab
Category : p
Grade : Grade III
Size :
M
1Ordnance Clothing Factory Avadi
Name
Specification
Use
Status
1) Fabrication of Shorts Cotton Light OG[21]()
Specification : FABRICATION OF SHORTS COTTON LIGHT OG
SWO PART II No.60215
SPECIFICATION:
1) DIMENSION : AS PER SPECN NO. PROV/OCFAV/GARMENT/005
2) CERTIFIED SAMPLE : AS PER APPROVED SAMPLE.
NOTE:
A) CUT COMPONENTS & GARNITURES WILL BE SU
E
Nonestab
2) FABRICATION OF OVERALL CE[21]()
Specification : FABRICATION OF OVERALL CE
SWO PART No. 60158
SPECIFICATION: No. IND/NAVY/TC/4660 WITH AMENDMENT NO.1
NOTE:
CUT COMPONENTS AND GARNITURES WILL BE SUPPLIED BY THE FACTORY.
DRAWING & SAMPLE WILL BE PROVIDED AT THE TIME OF FABRICA
13) HANDLE LEVER 765 58 221 C
Description : HANDLE LEVER 765 58 221 C()
Specification : HANDLE LEVER DRG. NO. 765-58-221/C
C
Estab
14) Hinge Driver Hatch Assembly forging
Description : Hinge Driver Hatch Assembly forging()
Specification : Hinge (Driver Hatch Assembly) forging
C
Estab
15) LOOM CLIP FOR ELECTRICAL FITMENT FOR MPV AS PER DRG NO HULL MPV 102
Description : LOOM CLIP FOR ELECTRICAL FITMENT FOR MPV AS PER DRG NO HULL MPV 102()
Specification : LOOM CLIP FOR ELECTRICAL FITMENT FOR MPV AS PER DRG NO HULL/MPV/102
Specification : ASSY TAIL LAMP BKT. DRG NO.261454400108 COSTING OF PT.NO/DRG NO.261454400110,ASSY GRILL GUARD TO DRG.NO.222654400101(b) MOUNTING BKT TO DRG NO.2226542008201a TWONOS EACH) BKT TO DRG. NO.261454408209, BKT.261454408208, CHANNEL 26145440820
C
Estab
3) LPTA Stud for water Tank
Description : LPTA Stud for water Tank()
Specification : STUD FOR WATER TANK FITMONT (4/SET) 2614 7061 8801 NOTE: - TO BE SUPPLIED IN YELLOW PASSIVATED CONDITION
C
Estab
4) LPTA Stud Rear
Description : LPTA Stud Rear()
Specification : STUD REAR (M12X260 LENGTH) PART NO. 215470618802N NOTE:- TO BE SUPPLIED IN YELLOW PASSIVATED CONDITION
C
Estab
5) Oil can Carrier LPTA Part No.- BPD11117-84
Description : Oil can Carrier LPTA Part No.- BPD11117-84()
Specification : As per specification / Drg. no./Pt. no. BPD11117-84
C
Estab
Category : p
Grade : 3
Size :
S
1Ammunition Factory Khadki
Name
Specification
Use
Status
1) BOX STEEL NO. S 6 MK1 DRG.ARDE 2225[65]()
Specification : DRG. NO. ARDE 2225 SHEET NO.3
C
Nonestab
2) BOX NO.428 MK.1[65]()
Specification : DRG. NO. D.D.(L) 18704
C
Nonestab
3) BOX C 28 A STEEL[65]()
Specification : DESIGNERS REF CIA/AMN/1180 PART NO.ISV 357 A
C
Nonestab
4) BOX M 104 MK1 PAINTED OLIVE GREEN[65]()
Specification : IA 1169
C
Nonestab
5) AMMN.CONTAINER BOX B-9 A[65]()
Specification : IA 1169
C
Nonestab
6) BOX G 70 MK1(STEEL)OLIVE GREEN.[65]()
Specification : IA 1169
C
Nonestab
7) BOX H2A DRG.CIA/AMMN/468[65]()
Specification : IA 1169
C
Nonestab
Category : p
Grade : Grade III
Size :
S
1Ammunition Factory Khadki
Name
Specification
Use
Status
1) BOX M 104 MK1 PAINTED OLIVE GREEN[65]()
Specification : IA 1169
C
Nonestab
2) AMMN.CONTAINER BOX B-9 A[65]()
Specification : IA 1169
C
Nonestab
3) BOX G 70 MK1(STEEL)OLIVE GREEN.[65]()
Specification : IA 1169
C
Estab
4) BOX 682 MKI W/O LINER IA 896/1[65]()
Specification : IA 1163
C
Nonestab
5) CARRIER 6A/L,STEEL,TO DESIGNER'S REF CIA/AMN/1162,PART NO.ISV 354-A,SPECN IA 1169 DULY PAINTED AS PER DRG WITH PAINT OF SHADE OLIVE GREEN ISC:220[65]()
1) SUPPLY OF GAS PORT BLOCK AS PER DRG NO K 1205 STAR 3 WITH FIRMS MATERIAL[70]()
Specification : SUPPLY OF GAS PORT BLOCK AS PER DRG NO K 1205 STAR 3 WITH FIRMS MATERIAL
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) SUPPLY OF PREMACHINED BLANK S 2 TO DRG NO TEND 2607 STAR 5 WITH OFT SUPPLIED MATERIAL REQUIRED FOR K 3001STAR4 FIXED BUTT FOR TAR[70]()
Specification : AS PER DRG NO. TEND 2607 STAR 5 WITH OFT MATERIAL
C
Nonestab
2) MANUFACTURING AND SUPPLY OF PREMACHINED BLANK S3 AS PER DRG NO TEND 2642 WITH OFT MATERIAL REQUIRED FOR K 4001 STAR 6 BODY[70]()
Specification : MANUFACTURING AND SUPPLY OF PREMACHINED BLANK S3 AS PER DRG NO TEND 2642 WITH OFT MATERIAL REQUIRED FOR K 4001 STAR 6 (BODY)
C
Nonestab
3) MANUFACTURE AND SUPPLY OF FRONT SIGHT BLOCK PRE MACHINED BLANKS FS AS PER DRG NO TEND 2668 WITH FIRMS MATERIAL FOR TRICHY ASSAULT RIFLE[70]()
Specification : MANUFACTURE AND SUPPLY OF FRONT SIGHT BLOCK PRE MACHINED BLANKS (FS) AS PER DRG NO.TEND 2668 WITH FIRM'S MATERIAL FOR TRICHY ASSAULT RIFLE
C
Nonestab
4) Manufacturing and supply of Picatinny Rail DRG Number TEND 2663 REQUIRED FOR MGL[70]()
Specification : MANUFACTURING AND SUPPLY OF PICATINNY RAIL OF MGL AS PER DRG NO. TEND 2663 REQUIRED FOR MGL
C
Nonestab
5) INPUT BLANKS FOR REAR SIGHT BLOCK COMPONENT AS PER DRG NO TEND 2634 STR 2 WITH FIRMS MATERIAL[70]()
Specification : INPUT BLANKS FOR REAR SIGHT BLOCK COMPONENT AS PER DRG NO TEND 2634 STR 2 WITH FIRMS MATERIAL
C
Nonestab
6) SUPPLY OF LOWER HAND GUARD LOCK PLATE AS PER DRG No K 3011 STAR REQUIRED FOR TAR[70]()
Specification : AS PER DRG No.K-3011* REQUIRED FOR TAR
C
Nonestab
7) SUPPLY OF HINGE PIN AS PER DRG No K 4015 WITH FIRMS MATERIAL REQUIRED FOR TAR[70]()
Specification : SUPPLY OF HINGE PIN AS PER DRG No K-4015 WITH FIRM'S MATERIAL REQUIRED FOR TAR
C
Nonestab
8) KEY[74]()
Specification : KEY (View) AS PER DRG NO.074264A-00 FOR COCKING MECH.ASSY OF SRCG
C
Nonestab
9) GUIDE RECOIL FRONT[74]()
Specification : GUIDE RECOIL FRONT (View) AS PER DRG NO.075870A-00 FOR CRADLE WEAPON ASSY OF SRCG
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) PRE MACHINED BLANK S2 AS PER DRG NO TEND 2449 STAR 10 WITH OFT RAW MATERIAL REQUIRED FOR K 4001 STR7[70]()
Specification : PRE MACHINED BLANK S2 AS PER DRG NO TEND 2449 STAR 10 WITH OFT RAW MATERIAL REQUIRED FOR K 4001 STAR 7
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) PRE MACHINED BLANK DRAWING TO TEND 2637 CYLINDER FOR 40MM MGL WITH FIRMS MATERIAL[70]()
Specification : PRE MACHINED BLANK DRAWING TO TEND 2637 CYLINDER FOR 40MM MGL WITH FIRM'S MATERIAL
C
Nonestab
2) SHIELD FRONT FOR 40MM MGL WITHOUT HEAT TREATMENT AS PER DRG NO TEND 2724[70]()
Specification : AS PER OFT REQUIREMENTS
E
Nonestab
3) PRE MACHINED BLANK FS FOR GAS PORT BLOCK WITH FIRMS MATERIAL TO DRG NO TEND 2611 STAR4 FOR TAR[70]()
Specification : PRE MACHINED BLANK FS FOR GAS PORT BLOCK WITH FIRMS MATERIAL TO DRG NO TEND 2611 STAR4 FOR TAR
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) RIVET SUPPORTING SIDE AS PER DRG NO K 4014 WITH FIRMS MATERIAL[70]()
Specification : AS PER DRG NO K 4014 WITH FIRMS MATERIAL
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) PREMACHINED BLANK AS PER DRG NO TEND 2616 STAR 3 FOR TAR TRUNNION[70]()
Specification : PREMACHINED BLANK AS PER DRG NO TEND 2616 STAR 3 FOR TAR TRUNNION
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) Change Lever RH[70]()
Specification : As per Drawing
C
Nonestab
2) Change Lever LH[70]()
Specification : As per Drawing
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) 44P03010 20MM HAMMER CAM PLATE[70]()
Specification : AS PER OFT SPECIFICATIONS
R
Nonestab
2) 44P14006 14 5MM HAMMER CAM PLATE[70]()
Specification : AS PER OFT REQUIREMENTS
R
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) FRAME BASKET WELD View AS PER DRG noY19388A 00 FOR MECH SRU ASSY OF SRCG[74]()
Specification : FRAME, BASKET, WELD (View) AS PER DRG.no.Y19388A-00. FOR MECH SRU ASSY OF SRCG.
R
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) SIDE FOLDABLE BUTT ASSY AS PER DRG NO K 4110 STAR 5 WITH FIRMS MATERIAL REQUIRED FOR TAR[70]()
Specification : SIDE FOLDABLE BUTT ASSY AS PER DRG NO K 4110 STAR 5 WITH FIRMS MATERIAL REQUIRED FOR TAR
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) Manufacture and supply of MGL Extractor before anodic coating to Drg No Tend 2252 st with firm material[70]()
Specification : Manufacture and supply of MGL Extractor before anodic coating to Drg No Tend 2252 st with firm material
R
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) MANUFACTURE AND SUPPLY OF MGL BLOCK SCREW PISTOL GRIP TO DRG NO 30P 3015 ST 3 WITH FIRM MATERIAL[70]()
Specification : MANUFACTURE AND SUPPLY OF MGL BLOCK SCREW PISTOL GRIP TO DRG NO 30P 3015 ST 3 WITH FIRM MATERIAL
Specification : Concetrated Nitric Acid, Strength-98% As per IS 264:2005 (Specification of CNA Explosive Grade) All other parameters to be as per (IS 264:2005)
R
Nonestab
Category : s
Grade : Grade II
Size :
S
1Ordnance Factory Varangaon
Name
Specification
Use
Status
1) Sodium Bichromate (Technical)[10]()
Specification : IS : 249-1979 (Third Revision)
Packed in 50 Kg of Polythene Lined Bags
R
Nonestab
Category : p
Grade : Grade III
Size :
S
1Ordnance Factory Varangaon
Name
Specification
Use
Status
1) Barium Nitrate Grade-I[10]()
Specification : To Specn. : JSS : 6810-59-2016, Revision No. 4,
DC No. 5480-ME Dtd. 24-09-20016.
R
Nonestab
Category : p
Grade : Grade III
Size :
S
1Ordnance Factory Varangaon
Name
Specification
Use
Status
1) Strontium Nitrate for Pyrotechnic Compo.[10]()
Specification : IS : 5671 of 1984.1st Rev. Amnd. No. 1, Reaffirmed 2011,
in the form of crystals without lumps, Particle Size :- Passing through 150 Micron I.S. sieve 100 BSS Min. 50% and retained on 63 Micron I.S. Sieve 240 BSS Min. 93%.
Packed in Pol
R
Nonestab
Category : p
Grade : Grade III
Size :
S
1Ordnance Factory Ambernath
Name
Specification
Use
Status
1) CHROMIC ACID[10]()
Specification : S PER REQUIREMENT / GIVEN SPECIFICATION.
R
Estab
Category : p
Grade : Grade III
Size :
S
2436
NEXT GENERATION TECHNOLOGIES
PLOT NO 176, G2, SANJANA EMERALD ROAD NO 2 P AND T COLONY MEDIPALLY HYDERABAD Telangana
PIN1 : 500092
Phone No. : 27206659 GSTIN :
36AAKFN1918L1ZY
Specification : VIDEO PROCESSING BOARD DRG NO. 096701070400000 ALONGWITH CONNECTORS AND MATING CABLE AS PER ATTACHED DRG/SPECN. AS APPENDIX-1 OF 0 TO 18 PAGES ( TOTAL 19 SHEETS)
C
Estab
Category : p
Grade : Grade III
Size :
S
1Opto Electronic Factory
Name
Specification
Use
Status
1) POWER SUPPLY CUM CONTROL BOARD (L.F.9001121272)[90]()
Specification : POWER SUPPLY CUM CONTROL BOARD DRG.NO. 096701070300000 ALONGWITH CONNECTORS AND MATING CABLE AS PER ATTACHED DRG./SPECN. AS PER APPENDIX-II OF 5 PAGES.
Specification : TAIL UNIT ASSEMBLY TO DRG.NO.AAIW/BS-0071
CONSISTING OF CONE TO DRG NO. AAIW/BS-0071/1, STABILISER FIN TO DRG NO. AAIW/BS-0071/2, STABILISER RING ASSEMBLY TO DRG NO. AAIW/BS-0071/3, AND BASE BUSH TO DRG NO. AAIW/BS-0071/4.
C
Nonestab
Category : ddp
Grade : Grade III
Size :
S
1Ordnance Factory Khamaria
Name
Specification
Use
Status
1) TAIL UNIT NO- TB 250 (9911358363)[99]()
Specification : TAIL UNIT NO.TB-250,DRG.NO.ARDE-9501-03 DT.19 APR 2000.AND SPECN.NO.ARDE/SPECN./613 PROVISIONALLY APPROVED ON 19 APR2000 AND AMENDED VIDE RCMA(AA)/1440/5/TECH DATED 29 APR 2010.PACKAGE DESCRIPTION-BOX STEEL NO.1 MK-I TO HOLD 1 TO DRG.NO.AR
C
Nonestab
Category : ddp
Grade : Grade III
Size :
L
1Ordnance Factory Khamaria
Name
Specification
Use
Status
1) BOX H-60 MK-I NEW W/O FMT (ARMY&NVL)[65]()
Specification : BOX H-60 MK-1 (INDIA) (NEW) AS PER DRG LIST NO ARM-1253, NO.OF SHEETS-3, SHEET-1 R.NO.9 DT.7-3-2002 SHEET-2 R.NO.5 DT.31-7-96 SHEET-3 R.NO.NIL DT 2-3-98 TO DRG NO.ARM-1253-D1(WITHOUT-FITMENTS) R.NO.6 DT.27-6-96. SPECN.: IA-1169(n)DC-35576
P
Nonestab
Category : ddp
Grade : Grade III
Size :
S
2438
Maa Chandra Chemical
53 Uptron state panki Side 1 Kanpur Panki Kanpur Uttar Pradesh
PIN1 : 208009
Phone No. : 9838775770 GSTIN :
09AATFM7014M1ZM
1) BRUSH AS PER DRG No K 9003 STAR WITH FIRMS MATERIAL[70]()
Specification : AS PER DRG No K 9003* WITH FIRMS MATERIAL
E
Nonestab
Category :
Grade : Grade III
Size :
S
1Ordnance Factory Tiruchirapalli
Name
Specification
Use
Status
1) PULL THROUGH 1A NYLON AS PER DS CAT NO 1005 001760 FOR DC NO 22520 SA DATED 2 point 5 point 94 LATEST ISSUE TO BE FOLLOWED FOR RIFLE 7point 62mm 1A1[70]()
Specification : AS PER DS CAT NO.1005-001760 FOR DC NO. 22520-SA DATED 2.5.94 LATEST ISSUE TO BE FOLLOWED FOR RIFLE 7.62mm 1A1
E
Nonestab
2) PULLTHROUGH WEIGHT FOR 7POINT62MM RIFLE[70]()
Specification : AS PER DRG
E
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) CLEANING ROD WITH BRUSH AND PULL THROUGH TO DRG.NO.SK-4142[70]()
Specification : CLEANING ROD WITH BRUSH AND PULL THROUGH TO DRG.NO.SK-4142
C
Nonestab
Category :
Grade : Grade III
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) BRUSH CLEANING BRACKET AND CYLINDER GAS[71]()
Specification : BRUSH CLEANING BRACKET,& CYLINDER GAS TO DRG.NO-CQA(SA)SK-459,DS CAT NO-1005-560082. DC(1)NO-26532-SA,DTD-30.07.2010.
1) FINISHED FORGED HEAD COMPONENT OF 100/120 KGS. AERIAL BOMB[42]()
Specification : FINISHED FORGED HEAD COMPONENT OF 100/120 KGS. AERIAL BOMB
FINISHED FORGED HEAD COMPONENT OF 100/120 KGS. AERIAL BOMB
AS PER TERMS & CONDITIONS OF ANNEXURE 'A' ATTACHED
C
Nonestab
Category : dp
Grade : Grade II
Size :
L
1Grey Iron Foundry
Name
Specification
Use
Status
1) FORGED HEAD (UN-MACHINED) FOR 100-120 KG. AERIAL BOMB AS PER GIF DRAWING NO. 5310-A/FORGE AND TERMS & CONDITIONS ENCLOSED[66]()
Specification : FORGED HEAD (UN-MACHINED) FOR 100-120 KG. AERIAL BOMB
AS PER GIF DRAWING NO. 5310-A/FORGE
