Specification : STEEL ROUND 18.00 MM TO SPECN. BS:970PT.1:1983
GD.655 M13 (EN 36B).(FOR STUD CHANGE LEVER).
R
Estab
Category : s
Grade : 3
Size :
S
1Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) SM SHEET CR
Description : SM SHEET CR()
Specification : SM SHEET CR 1.25X1250X2500MM BS:1449:PT.1:1983 CR-3 SEC.2
OR IS:513:1994 REQD.FOR STOP D S CAT NO 1005-000975 9MM
MAGZINE CARBINE 1A1/CARBURIZING BOX.
R
Estab
Category : s
Grade : 3
Size :
S
1Field Gun Factory Kanpur
Name
Specification
Use
Status
1) PHOSPHOR BRONZE SIZE 45MM SQUARE X1350 IN MULTIPLE LENGTH SPECN IS 7811 OF 1993[07]()
Specification : PHOSPHOR BRONZE SIZE 45MM SQUARE X1350 IN MULTIPLE LENGTH SPECN IS 7811 OF 1993
R
Estab
Category :
Grade : Grade III
Size :
S
1Gun and Shell Factory
Name
Specification
Use
Status
1) BRASS RODS 38point1 plus minus 0point1mm DIA TO SPEC BS 2874 1986 CZ 122 PB 3 IN M CONDITION[07]()
Specification : BRASS RODS 38.1+/- 0.1mm DIA BS 2874:1986 -CZ 122 PB-3 IN "M" CONDITION.
Specification : STEEL FLAT 25X32MM(1"X1-1/4")TO SPECN.BS:970:PT-1:1983 GD.080M40 IN HOT ROLLED & NORMALISED CONDITION. MATL TO BE TESTED AS PER ANNEXURE-C (REQD.FOR BAND FRONT SIGHT OF MAG 7.62MM)
R
Estab
2) DIA 6MM SS WIRE ROD IS6528 1972 GR 04 CR 18 NI 10 FULLY SOFTENED FOR FIRING DEVICE
Description : DIA 6MM SS WIRE ROD IS6528 1972 GR 04 CR 18 NI 10 FULLY SOFTENED FOR FIRING DEVICE()
Specification : DIA 6MM SS WIRE ROD IS6528-1972 GR 04 CR 18 NI 10 FULLY SOFTENED
R
Estab
3) STEEL ROUND 18MM DIA FOR MAG
Description : STEEL ROUND 18MM DIA FOR MAG()
4) STEEL ROUND dia for JVPC
Description : STEEL ROUND dia for JVPC()
Specification : SPECN:IS:5517-1993 grade 40 NI 6CR4 Mo3(EN-24)
R
Estab
5) ST.RD.25 MM DIA IN HOT ROLLED & ANNEALED/NORMLISED CONDTION TO SPECIFICATION BS:970.PT.1 1983 GD.605M36
Description : ST.RD.25 MM DIA IN HOT ROLLED & ANNEALED/NORMLISED CONDTION TO SPECIFICATION BS:970.PT.1 1983 GD.605M36()
6) STEEL FLAT 17X47 MM FOR-SHOULDER LOCKING LEFT & RIGHT DS CAT 1005-007907
Description : STEEL FLAT 17X47 MM FOR-SHOULDER LOCKING LEFT & RIGHT DS CAT 1005-007907()
7) STEEL FLAT 70 X 34 MM IN HOT ROLLED and ANNEALED CONDITION
Description : STEEL FLAT 70 X 34 MM IN HOT ROLLED and ANNEALED CONDITION()
Specification : SPECN.BS:970:PT-3:1991.GD.410S21 OR 420S29.TEST PIECE TO BE TESTEDAS PER RULINF SECTION. MATL.SHOULD SATISFY MACRO-ETCH TEST &MICROSCOPIC NON-METALIC INCLUSION RATING AS PER NATURE-C A SEPARATE T.P.TO BE HARDNED TO ACHIEVE HARDNESS 265
R
Estab
Category : s
Grade : 3
Size :
S
1Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) Steel Strip
Description : Steel Strip()
Specification : Steel Strip Size :- 1,8MM THICK X270 MM WIDE X1600 MM LONG TO SPECN. IS:7226-1974 GRADE C-40. COLD ROLLED & ANNEALED CONDN.
Note: GRAIN DIRECTION SHOULD BE ALONG THE LENGTH
Specification : STEEL ROUND 20MM DIA TO SPECN.BS:970:PT.1:1983 GD.080M40 IN HOT ROLLED &NORMALISED CONDITION. TEST PIECE TO BE TESTED AS PER THE SPECIFICATION.
R
Estab
4) ST.FLAT 40X16MM TO SPECN.IS:5517-1993 DEGIGNATION 40 CB . (FOR BRACKET FRONT HAND GUARD).
Description : ST.FLAT 40X16MM TO SPECN.IS:5517-1993 DEGIGNATION 40 CB . (FOR BRACKET FRONT HAND GUARD).()
Specification : STEEL FLAT 25X32MM(1"X1-1/4")TO SPECN.BS:970:PT-1:1983 GD.080M40 IN HOT ROLLED & NORMALISED CONDITION. MATL TO BE TESTED AS PER ANNEXURE-C (REQD.FOR BAND FRONT SIGHT OF MAG 7.62MM)
R
Estab
6) STEEL RD 25MM DIA FOR MAG
Description : STEEL RD 25MM DIA FOR MAG()
Specification : SPECN.BS:970:PT-3:1991 GD.420S29 OR 431S29HARDENED & TEMPERED BARS TO HARDNESS 265-300 BHN.MACRO ETCH & NMIR TEST TO BE CARRIED OUT AS PER ANNEXURE NATURE `C'. (REQUIRED FOR GAS REGULATOR D S CAT NO. 1005-006614)
Specification : STEEL ROUND 27 MM TO SPECN.IS:5517-1993 DEGIGNATION 55C8 IN ANNEALED & COLD DRAWN CONDN. (FOR SLEEVE LOCKING BIPOD).
R
Estab
8) STEEL ROD 30MM DIA. TO SPECN.BS:970:PT.1:1983 GD.070M55 CONDN.'S' (REQD. FOR FLASH HIDER )
Description : STEEL ROD 30MM DIA. TO SPECN.BS:970:PT.1:1983 GD.070M55 CONDN.'S' (REQD. FOR FLASH HIDER )()
9) DIA 6MM SS WIRE ROD IS6528 1972 GR 04 CR 18 NI 10 FULLY SOFTENED FOR FIRING DEVICE
Description : DIA 6MM SS WIRE ROD IS6528 1972 GR 04 CR 18 NI 10 FULLY SOFTENED FOR FIRING DEVICE()
Specification : DIA 6MM SS WIRE ROD IS6528-1972 GR 04 CR 18 NI 10 FULLY SOFTENED
R
Estab
10) ST.FLAT 125 X 8 X 530 MM LONG IN CUT LENGTH IN H.R & NORM. CONDN. TO SPECN.IS:5517-1993
Description : ST.FLAT 125 X 8 X 530 MM LONG IN CUT LENGTH IN H.R & NORM. CONDN. TO SPECN.IS:5517-1993()
Specification : ST.FLAT 125 X 8 X 530 MM LONG IN CUT LENGTH IN H.R & NORM. CONDN. TO SPECN.IS:5517-1993 DESIGNATION 55C8 TEST PIECE TO BE TESTED AS PER SPECN.TOLLERANCE ON WIDTH +/-2MM,ON THICKNE
SS +/-0.25MM.
R
Estab
11) STEEL ROUND 18MM DIA FOR MAG
Description : STEEL ROUND 18MM DIA FOR MAG()
12) STEEL STRIP 3.5MM THICK X 32MM WIDE TO SPECN. BS:5770:PT-II:1981 GD.70 OR 80 IN COLD ROLLED & ANNEALED CONDITION
Description : STEEL STRIP 3.5MM THICK X 32MM WIDE TO SPECN. BS:5770:PT-II:1981 GD.70 OR 80 IN COLD ROLLED & ANNEALED CONDITION()
Specification : SPECN. BS:5770:PT-II:1981 GD.70 OR 80 IN COLD ROLLED & ANNEALED CONDITION
R
Estab
13) ST.RD.25 MM DIA IN HOT ROLLED & ANNEALED/NORMLISED CONDTION TO SPECIFICATION BS:970.PT.1 1983 GD.605M36
Description : ST.RD.25 MM DIA IN HOT ROLLED & ANNEALED/NORMLISED CONDTION TO SPECIFICATION BS:970.PT.1 1983 GD.605M36()
14) STEEL RD 25 MM DIA ( REQUIRED FOR GAS REGULATOR DS CAT NO. 1005-006614)
Description : STEEL RD 25 MM DIA ( REQUIRED FOR GAS REGULATOR DS CAT NO. 1005-006614)()
Specification : SPECN BS: 970:PT-3:1991 GD.420S29 OR 431 S29
R
Estab
15) STEEL RD 22MM DIA IN HOT ROLLED AND ANNEALED CONDITION TO SPECN.BS:970 PT.1:1983 GD.817M40 OR 826M40.
Description : STEEL RD 22MM DIA IN HOT ROLLED AND ANNEALED CONDITION TO SPECN.BS:970 PT.1:1983 GD.817M40 OR 826M40.()
Specification : SPECN.BS:970 PT.1:1983 GD.817M40 OR 826M40.
R
Estab
16) STEEL FLAT 70 X 34 MM IN HOT ROLLED and ANNEALED CONDITION
Description : STEEL FLAT 70 X 34 MM IN HOT ROLLED and ANNEALED CONDITION()
Specification : SPECN.BS:970:PT-3:1991.GD.410S21 OR 420S29.TEST PIECE TO BE TESTEDAS PER RULINF SECTION. MATL.SHOULD SATISFY MACRO-ETCH TEST &MICROSCOPIC NON-METALIC INCLUSION RATING AS PER NATURE-C A SEPARATE T.P.TO BE HARDNED TO ACHIEVE HARDNESS 265
R
Estab
17) STEEL FLAT 17X47 MM FOR-SHOULDER LOCKING LEFT & RIGHT DS CAT 1005-007907
Description : STEEL FLAT 17X47 MM FOR-SHOULDER LOCKING LEFT & RIGHT DS CAT 1005-007907()
18) St Rd 3 point 25mm dia for JVPC
Description : St Rd 3 point 25mm dia for JVPC()
Specification : St. Rod 3.25MM dia to Specn. IS:5517-1993.40CB(EN-8) (Pin St. Hdls. Cocking Bracket & Gas block)
R
Estab
19) STEEL FLATS
Description : STEEL FLATS()
Specification : AS PER SPECIFICATION
R
Estab
20) Steel flat 36mm x 62mm for JVPC
Description : Steel flat 36mm x 62mm for JVPC()
Specification : BS:970 Pt.I 1983 GD 835 M 15 OR EN-39-B
R
Estab
21) LEADED PHOS BRONZE ROD 32MM DIA
Description : LEADED PHOS BRONZE ROD 32MM DIA()
Specification : LEADED PHOS.BRONZE ROD 32MM DIA TO SPECN.BS:2874:1969 PB102M
R
Estab
Category : s
Grade : 3
Size :
S
1Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) DIA 64MM+/-0.5MM STEEL ROD
Description : DIA 64MM+/-0.5MM STEEL ROD()
Specification : DIA 64MM+/-0.5MM STEEL ROD TO SPECIFICATION IS:7283 1992 WITH MATERIAL TO CHEMICAL & MECHANICAL PROPERTY REQUIRMENTS OF IS:226 1975 FE 410-5 OR BS 970 PT1 :1991 GRADE 070 M 20 NORMALISED
R
Estab
Category : s
Grade : 3
Size :
S
1Small Arms Factory
Name
Specification
Use
Status
1) ST FLAT 70X34MM IN HOT ROLLED and ANNEALED CONDITION[01]()
Specification : ST.FLAT 70X34MM IN HOT ROLLED & ANNEALED CONDITION TO SPECN. BS:970:PT-3:1991.GD.410S21 OR 420S29.TEST PIECE TO BE TESTED AS PER RULINF SECTION. MATL.SHOULD SATISFY MACRO-ETCH TEST & MICROSCOPIC NON-METALIC INCLUSION RATING(II) AS PER NAT
R
Nonestab
2) STEEL FLAT 17X47MM IN HOT ROLLED AND ANNEALED AT 650 C[03]()
Specification : STEEL FLAT 17X47MM IN HOT ROLLED AND ANNEALED AT 650'C TO SPECN.BS:970:PT-3:1991 GD.945M38 T.P.TESTED IN `T'CONDITION MACRO ETCH TEST & NMIR TEST AS PER ANNEXURE-A NATURE-C. (REQD.FOR-SHOULDER LOCKING LEFT & RIGHT DS CAT 1005-007907)
R
Nonestab
3) STEEL FL 50X25MM[04]()
Specification : STEEL FL.50X25MM TO IS:5517-1993 GD-40 NI6CR4MO3.
R
Nonestab
4) STEEL FLAT 36 MM X 62 MM[04]()
Specification : STEEL FLAT 36 MM X 62 MM BS: 970 PT-1 1983 GD. 835 M 15 OR EN- 39-B
R
Nonestab
5) STEEL FLAT SIZE 6 X 22 MM IN HOT ROLLED AND NORMALISED CONDN FOR MAG[01]()
Specification : STEEL FLAT SIZE:- 6 X 22MM IN HOT ROLLED & NORMALISED CONDN.TO SPECIFICATION BS:970:PT.3:1991:GR.070M55 MATERIAL TO BE TESTED IN HARDENED & TEMPERED CONDITION AS PER RULING SECTION & SEPERATE TEST PIECE NEED TO BE HEAT TREATED TO ACHIEVE
R
Nonestab
6) STEEL FLAT 45X50 070M55 OR EN9 FOR MAG[01]()
Specification : STEEL FLAT TO SPECIFICATION IS:5517-1993 DESIGNATION 55C8 SIZE 45MM X 50MM IN FORGED AND ANNEALED CONDITION
R
Nonestab
7) PHOS BRONZE ROD 32MM DIA FOR MAG[07]()
Specification : PHOS.BRONZE ROD 32MM DIA TO SPECN.BS:2874:1969 PB102M
R
Nonestab
8) ST ROD 42MM DIA[04]()
Specification : ST.ROD 42MM DIA TO SPECIFICATION IS-4432-1988 GD-13NI 13 CR3 WITH RESTRICTIONS S%=0.010MAX.,P%=0.015MAX.&(S+P)%=0.022MAX. GROUND & POLISHED BEFORE ROLLING.NORMALISED & PICKLED.RING GRIND TESTED TO ENSURE FORGING QUALITY.04-06METERS LONG.O
R
Nonestab
9) STEEL ROD 30MM DIA[01]()
Specification : Steel Rod 30mm dia. To Specn. IS:5517:1993 Designation 55CB.
R
Nonestab
10) STEEL ROUND DIA 25MM[01]()
Specification : STEEL ROUND DIA 25MM TO AS PER SPEC. IS:4431-1978 DESIGNATION 11C10S25
R
Nonestab
11) STEEL FLAT SIZE 45MM X 50MM IN FORGED AND ANNEALED CONDITION[01]()
Specification : STEEL FLAT TO SPECIFICATION IS:5517-1993 DESIGNATION 55C8 SIZE 45MM X 50MM IN FORGED AND ANNEALED CONDITION
R
Nonestab
12) ST RD 6 point 35MM[01]()
Specification : ST. RD. 6.35MM DIA TO SPECN. IS 5517-1993, GD 30C8
R
Nonestab
13) STEEL SQUARE 22MM HOT ROLLED AND NORMALISED CONDITION TO SPECN BS 970 PT3 1991 GD070M55[01]()
Specification : STEEL SQR. 22MM (7/8”) HOT ROLLED & NORMALISED CONDITION TO SPECN :BS:970 :PT-3 :1991 GD.070M55
R
Nonestab
14) Steel Flat 75x40mm[01]()
Specification : ST. FLAT 75(+/-5.0)MM X 40(+/-2.0)MM TO SPECN IS:6603-2001, DESIGNATION X12CR12 OR X20CR13. MACRO ETCH TEST & NMIR TEST (FOR MODERATELY/NON-STRESSED(II)) AS PER ANX. ‘A’ NATURE ‘C’
R
Nonestab
15) STEEL RD 25MM DIA[03]()
Specification : STEEL RD 25MM DIA SPECN.IS:6603-2001,DESIG-X15CR16 NI2
HARDENED & TEMPERED BARS TO HARDNESS 265-300 BHN.MACRO ETCH & NMIR TEST(II) TO BE CARRIED OUT AS PER ANNEXURE NATURE `C' (REQUIRED FOR GAS REGULATOR D S CAT NO. 1005-006614)
R
Nonestab
16) STEEL ROUND 18MM DIA[01]()
Specification : STEEL ROUND 18MM DIA TO SPECN:BS:970:PT 1:1983 GD 605 M36
OR GD 606 M36 MACRO ETCH AND NMIR TEST (MODERATELY STRESSED/NON STRESSED
COMPONENTS)AS PER ANNEXURE "A" NATURE-C
1) Cartridge Guide Pawl Right Hand Air Version Drg No 3602002613
Description : Cartridge Guide Pawl Right Hand Air Version Drg No 3602002613()
Specification : Cartridge Guide Pawl Right Hand Air Version MAG 7.62mm Drg. No. 3602002613, Classment 067A, PL. No.A3-3
C
Estab
Category : p
Grade : 3
Size :
S
1Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) Sear for LMG
Description : Sear for LMG()
Specification : SEAR AS PER DRG.NO. ARDE/SK-2689/239 IN SOFT CONDITION DS CAT NO 1005-007736 DC(1)26924-SA DT-30.08.16
C
Estab
Category : p
Grade : 3
Size :
S
1Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) STEEL BLANK OF BARREL EXTENSION UPTO STAGE 5 FOR RIFLE 5 56
Description : STEEL BLANK OF BARREL EXTENSION UPTO STAGE 5 FOR RIFLE 5 56()
Specification : STEEL BLANK OF BARREL EXTENSION UPTO STAGE 5 AS PER DRG. NO. SK-5092*2(RAW MATERIAL SIZE- 40X50 MM BS:970 PT.1-1983,817 M40 "T"(BS:970 EN 24 "T")COND.HARDNESS 248-302 HB AGAINST L.F. NO. 0334032650 WILL BE SUPPLIED BY SAF AGAINST B/G).
C
Estab
2) BARREL (BLANK) REQUIRED FOR REVOLVER MK-III DRG NO SK-5381R* D.A. NO. 41/08
Description : BARREL (BLANK) REQUIRED FOR REVOLVER MK-III DRG NO SK-5381R* D.A. NO. 41/08()
Specification : BARREL (BLANK) REQUIRED FOR REVOLVER MK-III DRG NO SK-5381R* D.A. NO. 41/08
C
Estab
3) BLOCK GAS Drg. No AKC 02/4
Description : BLOCK GAS Drg. No AKC 02/4()
10) EXTRACTOR (SMALL ARMS CARTRIDGE) DS CAT NO.1005-006633 DC NO.25387-SA DT.07.06.02 IN FINISHED CONDN.
Description : EXTRACTOR (SMALL ARMS CARTRIDGE) DS CAT NO.1005-006633 DC NO.25387-SA DT.07.06.02 IN FINISHED CONDN.()
Specification : EXTRACTOR (SMALL ARMS CARTRIDGE) DS CAT NO.1005-006633 DC NO.25387-SA DT.07.06.02 IN FINISHED CONDN.
C
Estab
11) SEAR DS CAT NO.1005-000617 DC NO. 26754-SA DT- 21.04.15 IN SOFT CONDITION.
Description : SEAR DS CAT NO.1005-000617 DC NO. 26754-SA DT- 21.04.15 IN SOFT CONDITION.()
Specification : SEAR DS CAT NO.1005-000617 DC NO. 26754-SA DT- 21.04.15 IN SOFT CONDITION.
C
Estab
Category : p
Grade : 3
Size :
S
1Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) PISTON EXTENSION BLANK Drg. No AKC-07/01
Description : PISTON EXTENSION BLANK Drg. No AKC-07/01()
Specification : AS PER DRG
C
Estab
2) Blank for Piston extension Stage-VII drg .no. ASK-4737*4 for LMG/Rifle 5.56mm
Description : Blank for Piston extension Stage-VII drg .no. ASK-4737*4 for LMG/Rifle 5.56mm()
Specification : AS PER DRG.
C
Estab
3) STEEL BLANK FOR PISTON EXTENSION STAGE VI(SIXTH) TO DRG NO-SK-5143*.
Description : STEEL BLANK FOR PISTON EXTENSION STAGE VI(SIXTH) TO DRG NO-SK-5143*.()
Specification : STEEL BLANK FOR PISTON EXTENSION STAGE VI(SIXTH) TO DRG NO-SK-5143*. NOTE:RAW MATERIAL WILL BE SUPPLIED BY SAF ON FREIGHT TO PAY BASIS AGAINST THE B/G THROUGH L/FOLIO NO.0412001042.
C
Estab
4) BARREL EXTENSION BLANK FOR SMALL ARMS
Description : BARREL EXTENSION BLANK FOR SMALL ARMS()
Specification : AS PER DRAWING
C
Estab
5) PAWL HAMMER FOR RIFLE 5 56
Description : PAWL HAMMER FOR RIFLE 5 56()
Specification : Pawl Hammer ARDE SK 2689/170 to DS CAT No. 3040-003115 in finished condition
C
Estab
6) EXTRACTOR SMALL ARMS CARTRIDGE DRG NO. ARED /SK/2689/250
Description : EXTRACTOR SMALL ARMS CARTRIDGE DRG NO. ARED /SK/2689/250()
Specification : AS PER DRG.
C
Estab
7) HAMMER TO DS CAT NO. 1005-008003
Description : HAMMER TO DS CAT NO. 1005-008003()
Specification : AS PER DRG.
C
Estab
8) SEAR SAFETY FOR SMALL ARMS
Description : SEAR SAFETY FOR SMALL ARMS()
Specification : AS PER DRAWING
C
Estab
9) GUIDE PISTON Drg. No AKC/02/3*1
Description : GUIDE PISTON Drg. No AKC/02/3*1()
Specification : AS PER DRG
C
Estab
10) FORE SIGHT HOUSING TO DS CAT NO. 1005-000426 DC(I) NO. 26593-SA DT- 20.07.11 IN WITH OUT HEAT TREATMENT CONDITION.
Description : FORE SIGHT HOUSING TO DS CAT NO. 1005-000426 DC(I) NO. 26593-SA DT- 20.07.11 IN WITH OUT HEAT TREATMENT CONDITION.()
Specification : FORE SIGHT HOUSING TO DS CAT NO. 1005-000426 DC(I) NO. 26593-SA DT- 20.07.11 IN WITH OUT HEAT TREATMENT CONDITION.
C
Estab
11) Sear Tripper for MAG 7.62 mm DS CAT 1005-000620
Description : Sear Tripper for MAG 7.62 mm DS CAT 1005-000620()
Specification : As Per Drg.
C
Estab
12) Cartridge guide Pawl
Description : Cartridge guide Pawl()
Specification : As Per Drg.
C
Estab
Category : p
Grade : 3
Size :
S
1Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) PISTON EXTENSION BLANK Drg. No AKC-07/01
Description : PISTON EXTENSION BLANK Drg. No AKC-07/01()
Specification : AS PER DRG
C
Estab
2) Blank for Piston extension Stage-VII drg .no. ASK-4737*4 for LMG/Rifle 5.56mm
Description : Blank for Piston extension Stage-VII drg .no. ASK-4737*4 for LMG/Rifle 5.56mm()
Specification : AS PER DRG.
C
Estab
3) STEEL BLANK FOR PISTON EXTENSION STAGE VI(SIXTH) TO DRG NO-SK-5143*.
Description : STEEL BLANK FOR PISTON EXTENSION STAGE VI(SIXTH) TO DRG NO-SK-5143*.()
Specification : STEEL BLANK FOR PISTON EXTENSION STAGE VI(SIXTH) TO DRG NO-SK-5143*. NOTE:RAW MATERIAL WILL BE SUPPLIED BY SAF ON FREIGHT TO PAY BASIS AGAINST THE B/G THROUGH L/FOLIO NO.0412001042.
C
Estab
4) BARREL EXTENSION BLANK FOR SMALL ARMS
Description : BARREL EXTENSION BLANK FOR SMALL ARMS()
Specification : AS PER DRAWING
C
Estab
5) PAWL HAMMER FOR RIFLE 5 56
Description : PAWL HAMMER FOR RIFLE 5 56()
Specification : Pawl Hammer ARDE SK 2689/170 to DS CAT No. 3040-003115 in finished condition
C
Estab
6) EXTRACTOR SMALL ARMS CARTRIDGE DRG NO. ARED /SK/2689/250
Description : EXTRACTOR SMALL ARMS CARTRIDGE DRG NO. ARED /SK/2689/250()
Specification : AS PER DRG.
C
Estab
7) HAMMER TO DS CAT NO. 1005-008003
Description : HAMMER TO DS CAT NO. 1005-008003()
Specification : AS PER DRG.
C
Estab
8) SEAR SAFETY FOR SMALL ARMS
Description : SEAR SAFETY FOR SMALL ARMS()
Specification : AS PER DRAWING
C
Estab
9) GUIDE PISTON Drg. No AKC/02/3*1
Description : GUIDE PISTON Drg. No AKC/02/3*1()
Specification : AS PER DRG
C
Estab
10) FORE SIGHT HOUSING TO DS CAT NO. 1005-000426 DC(I) NO. 26593-SA DT- 20.07.11 IN WITH OUT HEAT TREATMENT CONDITION.
Description : FORE SIGHT HOUSING TO DS CAT NO. 1005-000426 DC(I) NO. 26593-SA DT- 20.07.11 IN WITH OUT HEAT TREATMENT CONDITION.()
Specification : FORE SIGHT HOUSING TO DS CAT NO. 1005-000426 DC(I) NO. 26593-SA DT- 20.07.11 IN WITH OUT HEAT TREATMENT CONDITION.
C
Estab
11) Sear Tripper for MAG 7.62 mm DS CAT 1005-000620
Description : Sear Tripper for MAG 7.62 mm DS CAT 1005-000620()
Specification : As Per Drg.
C
Estab
12) Cartridge guide Pawl
Description : Cartridge guide Pawl()
Specification : As Per Drg.
C
Estab
Category : p
Grade : 3
Size :
S
1Small Arms Factory
[ENR Registration]
Name
Specification
Use
Status
1) PISTON EXTENSION BLANK Drg. No AKC-07/01
Description : PISTON EXTENSION BLANK Drg. No AKC-07/01()
Specification : AS PER DRG
C
Estab
2) Blank for Piston extension Stage-VII drg .no. ASK-4737*4 for LMG/Rifle 5.56mm
Description : Blank for Piston extension Stage-VII drg .no. ASK-4737*4 for LMG/Rifle 5.56mm()
Specification : AS PER DRG.
C
Estab
3) STEEL BLANK FOR PISTON EXTENSION STAGE VI(SIXTH) TO DRG NO-SK-5143*.
Description : STEEL BLANK FOR PISTON EXTENSION STAGE VI(SIXTH) TO DRG NO-SK-5143*.()
Specification : STEEL BLANK FOR PISTON EXTENSION STAGE VI(SIXTH) TO DRG NO-SK-5143*. NOTE:RAW MATERIAL WILL BE SUPPLIED BY SAF ON FREIGHT TO PAY BASIS AGAINST THE B/G THROUGH L/FOLIO NO.0412001042.
C
Estab
4) BARREL EXTENSION BLANK FOR SMALL ARMS
Description : BARREL EXTENSION BLANK FOR SMALL ARMS()
Specification : AS PER DRAWING
C
Estab
5) PAWL HAMMER FOR RIFLE 5 56
Description : PAWL HAMMER FOR RIFLE 5 56()
Specification : Pawl Hammer ARDE SK 2689/170 to DS CAT No. 3040-003115 in finished condition
C
Estab
6) EXTRACTOR SMALL ARMS CARTRIDGE DRG NO. ARED /SK/2689/250
Description : EXTRACTOR SMALL ARMS CARTRIDGE DRG NO. ARED /SK/2689/250()
Specification : AS PER DRG.
C
Estab
7) HAMMER TO DS CAT NO. 1005-008003
Description : HAMMER TO DS CAT NO. 1005-008003()
Specification : AS PER DRG.
C
Estab
8) SEAR SAFETY FOR SMALL ARMS
Description : SEAR SAFETY FOR SMALL ARMS()
Specification : AS PER DRAWING
C
Estab
9) GUIDE PISTON Drg. No AKC/02/3*1
Description : GUIDE PISTON Drg. No AKC/02/3*1()
Specification : AS PER DRG
C
Estab
10) FORE SIGHT HOUSING TO DS CAT NO. 1005-000426 DC(I) NO. 26593-SA DT- 20.07.11 IN WITH OUT HEAT TREATMENT CONDITION.
Description : FORE SIGHT HOUSING TO DS CAT NO. 1005-000426 DC(I) NO. 26593-SA DT- 20.07.11 IN WITH OUT HEAT TREATMENT CONDITION.()
Specification : FORE SIGHT HOUSING TO DS CAT NO. 1005-000426 DC(I) NO. 26593-SA DT- 20.07.11 IN WITH OUT HEAT TREATMENT CONDITION.
C
Estab
11) Sear Tripper for MAG 7.62 mm DS CAT 1005-000620
Description : Sear Tripper for MAG 7.62 mm DS CAT 1005-000620()
Specification : As Per Drg.
C
Estab
12) Cartridge guide Pawl
Description : Cartridge guide Pawl()
Specification : As Per Drg.
C
Estab
Category : p
Grade : 3
Size :
S
3283
Avon Springs & Accessories Pvt. Ltd.
7, SWALLOW LANE SWALLOW LANE Kolkata West Bengal
PIN1 : 700123
Phone No. : 9830946100
1) SPRING TO DET NO 1 7 OF DRG NO 3 02044 TO SK NO OTF PG 007 IN FINISHED CONDITION
Description : SPRING TO DET NO 1 7 OF DRG NO 3 02044 TO SK NO OTF PG 007 IN FINISHED CONDITION()
Specification : SPRING TO DET.NO.1-7 OF DRG.NO.3-02044(TO SK.NO.OTF/PG/007) IN FINISHED CONDITION
C
Estab
2) SPRING TO DET NO 5 OF DRG NO 3 022859
Description : SPRING TO DET NO 5 OF DRG NO 3 022859()
Specification : SPRING TO DET NO 5 OF DRG. NO. 3-022859 (TO SK NO OTF/SE/006) IN F/C
C
Estab
Category : p
Grade : 3
Size :
S
1Ordnance Factory Khamaria
[ENR Registration]
Name
Specification
Use
Status
1) SPRING WASHER TO DRG NO TRD 1 22267 LF 9911357852
Description : SPRING WASHER TO DRG NO TRD 1 22267 LF 9911357852()
Specification : SPRING WASHER TO DRG.NO.TRD-1-2-2267.
R
Nonestab
2) SPRING 5209544 FOR HEAT 551 LF 9911357927
Description : SPRING 5209544 FOR HEAT 551 LF 9911357927()
Specification : SPRING TO DRG NO.301100269.
R
Nonestab
3) SPIRAL DRG NO 8 367 009 LF 9911350871
Description : SPIRAL DRG NO 8 367 009 LF 9911350871()
1) MOUTH PIECE MAGAZINE D S CAT NO- 1005-000874 IN FINISHED CONDITION OF SMG 9MM CARBINE 1A1.DC(I)24752-SA-DT.16-06-2000
Description : MOUTH PIECE MAGAZINE D S CAT NO- 1005-000874 IN FINISHED CONDITION OF SMG 9MM CARBINE 1A1.DC(I)24752-SA-DT.16-06-2000()
Specification : MOUTH PIECE MAGAZINE D S CAT NO- 1005-000874 IN FINISHED CONDITION OF SMG 9MM CARBINE 1A1.DC(I)24752-SA-DT.16-06-2000
C
Estab
2) STUD BAYONET FOR CARBINE 9 MM
Description : STUD BAYONET FOR CARBINE 9 MM()
Specification : STUD BAYONET DS CAT NO-5307-000965 IN FINISHED CONDITION OF SMG 9MM CARBINE 1A1.DC(I)24785-SA-DT.26-07-2000.
C
Estab
3) PLATE RETAINER TO DS CAT NO.1005-000985 IN FINISHED CONDN. REQUIRED FOR 9MM MAGAZINE DC(I)NO 25698SA DT 16-03-2003
Description : PLATE RETAINER TO DS CAT NO.1005-000985 IN FINISHED CONDN. REQUIRED FOR 9MM MAGAZINE DC(I)NO 25698SA DT 16-03-2003()
Specification : PLATE RETAINER TO DS CAT NO.1005-000985 IN FINISHED CONDN. REQUIRED FOR 9MM MAGAZINE DC(I)NO 25698SA DT 16-03-2003
1) Adopter for Cleaning of Bore by pull Through
Description : Adopter for Cleaning of Bore by pull Through()
Specification : ADOPTER FOR CLEANING OF BORE BY PULL THROUGH OF RIFLE 5.56MMTO DRG.NO. CQA(SA)-180 DS CAT NO.1005-560405 DC (I)26520-SA DT.10/07/2010
C
Estab
2) RIVET SOLID FOR MAG
Description : RIVET SOLID FOR MAG()
Specification : RIVET SOLID MS RD.HD.4.107 X 9.5MM LONG DS CAT NO.5320-001336 IN FINISHED CONDITION DC(I) NO. 24714SA DT. 09.05.2000
C
Estab
3) RIVET SOLID FOR CHANNEL RIGHT FOR INSAS 5.56 MM
Description : RIVET SOLID FOR CHANNEL RIGHT FOR INSAS 5.56 MM()
Specification : ARDE SK 3143/51
C
Estab
4) RIVET FOR SMALL ARMS
Description : RIVET FOR SMALL ARMS()
Specification : AS PER DRAWING
C
Estab
5) RING RETAINING CARRYING HANDLE IN FINISHED CONDITION FOR RIFLE 5 56
Description : RING RETAINING CARRYING HANDLE IN FINISHED CONDITION FOR RIFLE 5 56()
Specification : RING RETAINING CARRYING HANDLE TO DRG NO CQA(SA) SK-422 DS CAT NO 5365-165210 IN FINISHED CONDITION. DC(I) NO. 26935-SA DT. 07/09/16
C
Estab
6) LEVER RIVETTING 5.56MM
Description : LEVER RIVETTING 5.56MM()
Specification : AS PER DRG.
C
Estab
7) Loop Sling Front finished condition to DRG No. ARDE/SK-3145/74 to DS CAT No.1005-008024
Description : Loop Sling Front finished condition to DRG No. ARDE/SK-3145/74 to DS CAT No.1005-008024()
Specification : Loop Sling Front finished condition to DRG No. ARDE/SK-3145/74 to DS CAT No.1005-008024
C
Estab
8) HOUSING LUG SLING DS CAT NO 1005 008021 IN FINISHED CONDITION
Description : HOUSING LUG SLING DS CAT NO 1005 008021 IN FINISHED CONDITION()
11) Pin straight headless for extractor DRG. No. SK-2689/71
Description : Pin straight headless for extractor DRG. No. SK-2689/71()
Specification : As per Drg.
C
Estab
12) PRECISION MECH. COMPONENTS, SUB ASSY./ASSEMBLY FOR SMALL ARMS
Description : PRECISION MECH. COMPONENTS, SUB ASSY./ASSEMBLY FOR SMALL ARMS()
Specification : AS PER DRAWING
C
Estab
13) PIN LEVER LOCKING D S CAT NO-1005-000871 IN FINISHED CONDITI ON OF SMG 9MM CARBINE 1A1.DC(I)26882-SA DT.02-07-16.
Description : PIN LEVER LOCKING D S CAT NO-1005-000871 IN FINISHED CONDITI ON OF SMG 9MM CARBINE 1A1.DC(I)26882-SA DT.02-07-16.()
Specification : PIN LEVER LOCKING D S CAT NO-1005-000871 IN FINISHED CONDITI ON OF SMG 9MM CARBINE 1A1.DC(I)26882-SA DT.02-07-16.
C
Estab
14) MOUTH PIECE MAGAZINE D S CAT NO- 1005-000874 IN FINISHED CONDITION OF SMG 9MM CARBINE 1A1.DC(I)24752-SA-DT.16-06-2000
Description : MOUTH PIECE MAGAZINE D S CAT NO- 1005-000874 IN FINISHED CONDITION OF SMG 9MM CARBINE 1A1.DC(I)24752-SA-DT.16-06-2000()
Specification : MOUTH PIECE MAGAZINE D S CAT NO- 1005-000874 IN FINISHED CONDITION OF SMG 9MM CARBINE 1A1.DC(I)24752-SA-DT.16-06-2000
C
Estab
15) PEG LOCATING D S CAT NO-1005-000877 IN FINISHED CONDITION OF SMG 9MM CARBINE 1A1. DC(I)-26883-SA-DT.04-07-16.
Description : PEG LOCATING D S CAT NO-1005-000877 IN FINISHED CONDITION OF SMG 9MM CARBINE 1A1. DC(I)-26883-SA-DT.04-07-16.()
Specification : PEG LOCATING D S CAT NO-1005-000877 IN FINISHED CONDITION OF SMG 9MM CARBINE 1A1. DC(I)-26883-SA-DT.04-07-16.
C
Estab
16) PLATE BAYONET STUD D S CAT NO-1005-000880 IN FINISHED CONDITION OF SMG 9MM CARBINE 1A1.DC(I)22976-SA-DT.24-05-95.
Description : PLATE BAYONET STUD D S CAT NO-1005-000880 IN FINISHED CONDITION OF SMG 9MM CARBINE 1A1.DC(I)22976-SA-DT.24-05-95.()
Specification : PLATE BAYONET STUD D S CAT NO-1005-000880 IN FINISHED CONDITION OF SMG 9MM CARBINE 1A1.DC(I)22976-SA-DT.24-05-95.
C
Estab
17) STUD BAYONET FOR CARBINE 9 MM
Description : STUD BAYONET FOR CARBINE 9 MM()
Specification : STUD BAYONET DS CAT NO-5307-000965 IN FINISHED CONDITION OF SMG 9MM CARBINE 1A1.DC(I)24785-SA-DT.26-07-2000.
C
Estab
18) Plate Bottom drg .no. 1005-000977 in finished condition for Carbine 9mm
Description : Plate Bottom drg .no. 1005-000977 in finished condition for Carbine 9mm()
Specification : AS PER DRG.no. 1005-000977
C
Estab
19) PLATE RETAINER TO DS CAT NO.1005-000985 IN FINISHED CONDN. REQUIRED FOR 9MM MAGAZINE DC(I)NO 25698SA DT 16-03-2003
Description : PLATE RETAINER TO DS CAT NO.1005-000985 IN FINISHED CONDN. REQUIRED FOR 9MM MAGAZINE DC(I)NO 25698SA DT 16-03-2003()
Specification : PLATE RETAINER TO DS CAT NO.1005-000985 IN FINISHED CONDN. REQUIRED FOR 9MM MAGAZINE DC(I)NO 25698SA DT 16-03-2003
C
Estab
20) REBOUND SLIDE TO DRG NO PHMK-III-1-22 IN FINISHED CONDITION REQUIRED FOR REVOVER MK-III
Description : REBOUND SLIDE TO DRG NO PHMK-III-1-22 IN FINISHED CONDITION REQUIRED FOR REVOVER MK-III()
Specification : REBOUND SLIDE TO DRG NO PHMK-III-1-22 IN FINISHED CONDITION REQUIRED FOR REVOVER MK-III
C
Estab
21) PLUNGER PAWL FOR REVOLVER MK-III DRG NO PHMK-III-1-34 IN FINISHED CONDITION
Description : PLUNGER PAWL FOR REVOLVER MK-III DRG NO PHMK-III-1-34 IN FINISHED CONDITION()
Specification : PLUNGER PAWL FOR REVOLVER MK-III DRG NO PHMK-III-1-34 IN FINISHED CONDITION
C
Estab
22) SAFETY FOR REVOLVER MK III REQUIRED IN FINISHED CONDITION DRG NO PHMK III 1 23
Description : SAFETY FOR REVOLVER MK III REQUIRED IN FINISHED CONDITION DRG NO PHMK III 1 23()
Specification : SAFETY FOR REVOLVER MK-III REQUIRED IN FINISHED CONDITION DRG NO PHMK-III-1-23
C
Estab
23) BUSH MOUNTING FRONT TO DS CAT NO. 3120 - 004267 DC(I) NO. 23313-SA DT. 13.4.96 IN FINISHED CONDITION.
Description : BUSH MOUNTING FRONT TO DS CAT NO. 3120 - 004267 DC(I) NO. 23313-SA DT. 13.4.96 IN FINISHED CONDITION.()
Specification : BUSH MOUNTING FRONT TO DS CAT NO. 3120 - 004267 DC(I) NO. 23313-SA DT. 13.4.96 IN FINISHED CONDITION.
C
Estab
24) PLUNGER CONTROL REAR SIGHT LEAF TO DS CAT NO. 1005-000536 DC(I) NO.25744-SA DT-08/05/2003 IN FINISHED CONDITION.
Description : PLUNGER CONTROL REAR SIGHT LEAF TO DS CAT NO. 1005-000536 DC(I) NO.25744-SA DT-08/05/2003 IN FINISHED CONDITION.()
Specification : PLUNGER CONTROL REAR SIGHT LEAF TO DS CAT NO. 1005-000536 DC(I) NO.25744-SA DT-08/05/2003 IN FINISHED CONDITION.
C
Estab
25) EJECTOR for MAG 7 62MM
Description : EJECTOR for MAG 7 62MM()
Specification : EJECTOR TO DS CAT NO. 1005-000548 DC(I) NO. 27011-SA DT- 14.01.2017 IN FINISHED CONDITION.
C
Estab
26) STUD REAR RETURN SPRING ASSEMBLY FOR MAG
Description : STUD REAR RETURN SPRING ASSEMBLY FOR MAG()
1) Steel Investment Casting for CAP for Carbine 9mm
Description : Steel Investment Casting for CAP for Carbine 9mm()
Specification : STEEL INVESTMENT CASTING FOR CAP TO DRG NO. SK-3870*2 OF 9MM CARBINE 1A1
C
Estab
2) INVESTMENT CASTING TO DRG NO. SKM-755*4. FOR CATCH CARRYING HANDLE
Description : INVESTMENT CASTING TO DRG NO. SKM-755*4. FOR CATCH CARRYING HANDLE()
Specification : AS PER DRG.
C
Estab
3) IC BODY COCKING for MAG
Description : IC BODY COCKING for MAG()
Specification : I.C BODY COCKING SLIDE SKM-738*4
C
Estab
4) INVESTMENT CASTING TO DRG NO.SKM-775*1 FOR STOP CARTRIDGE OF MAG 7.62MM
Description : INVESTMENT CASTING TO DRG NO.SKM-775*1 FOR STOP CARTRIDGE OF MAG 7.62MM()
Specification : AS PER DRG.
C
Estab
5) INVESTMENT CASTING OF GAS REGULATOR TO DRG.NO. SK-3706/8*
Description : INVESTMENT CASTING OF GAS REGULATOR TO DRG.NO. SK-3706/8*()
Specification : AS PER DRG.
C
Estab
6) INVESTMENT CASTING OF HINGE COVER TO DRG. NO-SK-4760/05*1.
Description : INVESTMENT CASTING OF HINGE COVER TO DRG. NO-SK-4760/05*1.()
Specification : AS PER DRG.
C
Estab
7) PLATE BODY IC OF REV MK III
Description : PLATE BODY IC OF REV MK III()
Specification : PLATE BODY (IC) FOR REVOLVER MK-III DRG NO SK-5376R*1
C
Estab
8) HAMMER (IC) FOR REVOLVER MK-III DRG NO SK-5377R*1
Description : HAMMER (IC) FOR REVOLVER MK-III DRG NO SK-5377R*1()
Specification : HAMMER (IC) FOR REVOLVER MK-III DRG NO SK-5377R*1,
C
Estab
9) INVESTMENT CASTING TO DRG NO SKM 752 2 FOR BRACKET CARRYING HANDLE
Description : INVESTMENT CASTING TO DRG NO SKM 752 2 FOR BRACKET CARRYING HANDLE()
Specification : INVESTMENT CASTING TO DRG.NO.SKM-752*2 FOR BRACKET CARRYING HANDLE
1) Wooden Packing Box for 100-120 Kgs Aerial Bomb to Drg.No.KHPK-410026(Amended)GIF-SK-2257 for 100-120
Description : Wooden Packing Box for 100-120 Kgs Aerial Bomb to Drg.No.KHPK-410026(Amended)GIF-SK-2257 for 100-120()
1) CENTRAL PAWL SPRING
Description : CENTRAL PAWL SPRING()
Specification : CENTRAL PAWL SPRING DS CAT NO.5360-000514 DC(I) NO.27017-SA DT.27-01-17
C
Estab
2) FRONT GUIDE RETURN SPRING TO DS CAT NO. 2540-002853 DC(I) NO. 25535-SA DT-30/09/2002 IN FINISHED CONDITION.
Description : FRONT GUIDE RETURN SPRING TO DS CAT NO. 2540-002853 DC(I) NO. 25535-SA DT-30/09/2002 IN FINISHED CONDITION.()
Specification : FRONT GUIDE RETURN SPRING TO DS CAT NO. 2540-002853 DC(I) NO. 25535-SA DT-30/09/2002 IN FINISHED CONDITION. (MATERIAL WILL BE SUPPLIED BY S.A.F ON FREIGHT TO PAY AGAINST B/G.
C
Estab
3) BRACKET CATCH SLEEVE LOCKING BARREL TO DS CAT NO.5340-007585 DC(I) NO.25384-SA DT.4-06-02 IN FINISHED CONDITION.
Description : BRACKET CATCH SLEEVE LOCKING BARREL TO DS CAT NO.5340-007585 DC(I) NO.25384-SA DT.4-06-02 IN FINISHED CONDITION.()
Specification : BRACKET CATCH SLEEVE LOCKING BARREL TO DS CAT NO.5340-007585 DC(I) NO.25384-SA DT.4-06-02 IN FINISHED CONDITION.
C
Estab
4) SECURING NUT GAS REGULATOR PART NO 2013
Description : SECURING NUT GAS REGULATOR PART NO 2013()
1) BUSH BOLT AGB PART NO X3541715V1
Description : BUSH BOLT AGB PART NO X3541715V1()
Specification : BUSH BOLT - AGB ( 102-04) BUSH BOLT - AGB (102-04) DRG./PART NO. X-3541715(V-1)
C
Estab
2) BUSH BOLT AGB PART NO X3541815
Description : BUSH BOLT AGB PART NO X3541815()
Specification : BUSH BOLT - AGB (102-04) BUSH BOLT - AGB (102-04) DRG./PART NO.X-3541815(V-1) Y
C
Estab
3) SPRING CUP LH & RH DRAG LINK ASSY()
Specification : 1) SPRING CUP LH DRAG LINK ASSY, DRG./PT. NO. F1034310-V1 & 2) SPRING CUP RH DRAG LINK ASSY, DRG./PT. NO. F1034210-V1 (02 different items)
